1. Manuals
  2. Brands
  3. EMBLEM Manuals
  4. Laminator
  5. EASYLAM 140 C
  6. Operating instructions manual

EMBLEM EASYLAM 140 C Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Laminator
140 C
Operating instructions
Version 1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EASYLAM 140 C and is the answer not in the manual?

Questions and answers

Related Manuals for EMBLEM EASYLAM 140 C

Summary of Contents for EMBLEM EASYLAM 140 C

  • Page 1 Laminator 140 C Operating instructions Version 1.0...

  • Page 2: Installation

    Please read this operating instructions before installation and keep this for later use technical information model ......................EASYLAM 140C length ......................177 cm width ......................48 cm height ......................135 cm height working area ..................97 cm max. media width ...................143 cm usable roll length ....................1420 mm max.

  • Page 3: Electricity Connection

    Further advises for installation: Power supply: The connection sockets have to be close to the machine. • single-phase current 110 V - 230 V • frequency: 50 – 60 Hz • strength of electric current: 4,5 A Location The location to place the machine must provide enough space to work. Don’t forget that space is also needed to insert and remove the material.
  • Page 4 - 4 -...

  • Page 5: Safety Devices

    Make sure that your hands do not get between the rolls while the machine is opera- ting. EMBLEM EASYLAM 140C is eqipped with a safety mechanism which uses a slip clutch to stop the rotation of the rollers. In this way serious injuries or pinching of the fingers are avoided.

  • Page 6: Operation Of The Machine

    Operation of the machine When you start working stay directly in front of the machine. The laminator has to be turned on with the main switch (right down, inside the machine). The main switch is lighted in green. With the keys SPEED I or SPEED II you decide the speed of lamination. You can also use the footpedal to adjust the speed of the laminator.
  • Page 7 Insert the scroller into the right insert this end of the scroller into connection. Move the scroller that the left connection way, so the pin fits into the holding fixture. • Autogrip material insertion label on the side right end of scroller with pin.
  • Page 8 EASYLAM-CUTTER To equip your laminator with lamination film in a simple and economical way we recommend our EASYLAM-CUTTER (Art.-Nr.: 24959). Its knife has a special blade to minimize the danger of getting hurt or of damaging the rolls considerably. Advantages: you save time and material while insertingthe lamination film including liner no exposed knife point The following description of the procedure allows an economical consumption of the lamination film while equipping the lamina- tor with foil. The cutter simplifies the preparation of the machine and helps to learn it faster. You can get this tool at your local dealer or at www.dataplot.de. - 8 -...
  • Page 9 Procedure - EASYLAM CUTTER Place the lamination film between Hold the film tight and clamp the Make sure the lamination film is the rollers rollers rolled tight Feed foreward approx. 5cm of Position the blund part of the knife Cut the liner carefully lamination film between film and liner Use the sharp end in front of the...
  • Page 10 Laminate with backing paper: • Open the lamination roller by pressing the button OPEN key and put in the laminate as shown in the picture. Push an empty roller core onto the roll-up axle R3 so that the protective liner/backing paper can be rolled up. • After you have attached the laminate to the roll-down axle R4, separate the backing paper and use tape to fas- ten it to the cardboard core on the roll-up axle R3. Ensure that the protective liner has been fastened uniformly without cross creases. Pull the laminate between the rollers and stick it onto the upper roller with tape. When doing this ensure that the foil is spread out evenly across the whole width. If there are creases or folds, repeat the steps until the material is perfectly positioned.
  • Page 11 Mounting on rigid boards with EASYLAM There are different technics professional users execute. First you have to face two requirements: Mounting a print on a self adhesive board Mounting a self adhesive print on board General: Open the gap between the axles at that high of the board. Adjust the high of the supply plate to the high of the board. Move the board between the axles and close the gap by “FILM”-key.
  • Page 12 For requirement b) Mounting a self adhesive print on board: Pull of 3-4 cm of the liner of the self adhesive print and stick the print onto the board manually. Move the board between the axles and place the print on top of the upper axle like shown in graphic II. Start mounting by some push of the board to move between the axles and push “start”- key.
  • Page 13 Cut the liner of one half of the self adhesive media and mount this half by using the laminator pushing “start” key. Turn around and insert the board again. - 13 -...

  • Page 14: Ce Declaration Of Conformity

    DECLARATION OF CONFORMITY DATAPLOT GmbH Gutenbergstraße 15 24558 Henstedt-Ulzburg Company manufacturerof the brand EMBLEM, declares under our own responsility, that the machine: Brand: EMBLEM Model: Easylam Expert 140C Easylam Expert 160C Easylam 140C Easylam 160W Easylam 160C is in conformity with: The requirements of EU Directive 2006/42/EC.s...
  • Page 15 - 15 -...
  • Page 16 Dataplot GmbH • Gutenbergstraße 15 • D–24558 Henstedt–Ulzburg • Germany Tel. +49 41 93 995 0 • Fax +49 41 93 995 220 info@dataplot.de • www.dataplot.de...

Table of Contents