Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for EMBLEM Easylam Junior II
Summary of Contents for EMBLEM Easylam Junior II
- Page 1 Product Description and Operating Manual...
-
Page 2: Important Security Notice
The unit must never be connected to an electrical power supply, which is not conform with its elec- trical data. If the EMBLEM EASYLAM junior II does not work as expected, it has to be switched off immediately. Liquids or mechanical / metal parts may never be allowed to penetrate the unit.The power supply cable must not be squeezed or otherwise damaged. -
Page 3: Description Of The Emblem Easylam Junior Ii Laminator
Of course the laminator also is equipped for winding interlayer paper as used with standardand special films. The universality and cost efficiency of EASYLAM junior II makes it to the perfect laminator for use under professional conditions when small numbers of pieces are produced (advertising studios, printing offices, offices, copy centres, etc.). - Page 4 main switch, switches on/off of the laminator switch for permanent movement of laminator foot pedal - stepless control of speed adjusting screw lever foot pedal socket power cord page - 4 -...
-
Page 5: Inserting The Laminating Film
3. INSERTINg THE LAMINATINg FILM Put laminating film on the laminating axles of EASYLAM junior II. Insert brakes. Lift the backing paper and stick a 10cm "parkingstrip" onto the whole width of the laminate. Do not cut of the backing paper! Fold back the backing paper. - Page 6 Bent the corners of silicone paper as shown. Open pressure rolls, by moving the control lever up Pull laminating film through the pressure rolls ( see below) and reset the lever in fix position. Grab the silicone paper at the bent corners and pull off for approx. 0 cm, then fix the paper by means of the plastic fasteners.
-
Page 7: Diagram For Loading The Laminating Film
If the film reel has to be changed, or the work is to be interrupted for a longer time, wind the film up back into reel and store in accordance with manufacturer's recommendations. When the work is terminated, cover the EASYLAM junior II with a dust protection. It also is recommend to disconnect the power source from mains. -
Page 8: Adjustment Of Pressure
6. ADjUSTMENT OF PRESSURE A Lamination: Lamination of materials up to 1,5 mm thickness Both adjusting screws unscrew to upper stop position (position 0) in counterclockwise rotation. B Mounting: Mounting of materials between 1,5 - 25 mm thickness 1,5 1. Lift lever. . - Page 9 detail . 4. Use one of the adjusting screws in counterclockwise rotation to lift the lower pressure roll until the adjust plate has contact to the upper pressure roll. ( detail .) detail . . Now use the other adjusting screw in counterclockwise rotation to lift the lower pressure roll until this side of the adjust plate has contact to the upper pressure roll.
-
Page 10: Maintenance, Service
7. MAINTENANCE, SERVICE EMBLEM EASYLAM junior II has been designed as a maintenance-free device for professional use, which does not require special user's care. •cleaning - with technical gasoline, alcohol •pressure roll maintenance: use an agent for regeneration of rubber parts (for instance silicone oil),... -
Page 11: Power Supply
8. POWER SUPPLY The power cord for the laminator is equipped with a standard car-plug. Please connect this to the EMBLEM power supply unit. If using another power supply, make sure the correct connection / set up is used.(See scheme) -
Page 12: Table Of Contents
Content IMPORTANT SECURITY NOTICE 1. DESCRIPTION OF THE EMBLEM EASYLAM jUNIOR II LAMINATOR 2. PREPARATION AND INSPECTION OF THE LAMINATOR BEFORE OPERATION 3. INSERTINg THE LAMINATINg FILM DIAgRAM FOR LOADINg THE LAMINATINg FILM 4. LAMINATINg 5. PARKINg OF THE FILM, TERMINATION OF LAMINATION 6.
Need help?
Do you have a question about the Easylam Junior II and is the answer not in the manual?
Questions and answers