Temperature controller with countdown timer (60 pages)
Summary of Contents for Walton C Series
Page 1
Series C & Series TM User’s Manual Series C - On-Off Temperature Controller Series TM - Temperature Indicator TOTAL CUSTOMER CUSTOMER SATISFACTION SATISFACTION 3 Year Warranty ISO 9001 ISO 9001 Registered Company Winona, Minnesota USA 1241 Bundy Boulevard., Winona, Minnesota USA 55987 Phone: +1 (507) 454-5300, Fax: +1 (507) 452-4507 http://www.watlow.com 0600-0044-0000 Rev.
Safety Information We use note, caution and warning symbols throughout this book to draw your atten- tion to important operational and safety information. A “NOTE” marks a short message to alert you to an important detail. A “CAUTION” safety alert appears with information that is important for protecting your equipment and performance.
Overview Watlow's Series C family of basic temperature con- *Also available in an FM-approved limit version. trollers* provide an economical controller solution for applications where simple on/off control is needed. Features and Benefits These controllers are available with or without an Four-Character LED Display operator interface and can be ordered in square 1/8th •...
Installation Installing the Open Board Controller 61.7 mm 45.07 mm 45.07 mm 61.7 mm 2.43 in 2.43 in 1.775 in 1.775 in 56.3 mm 56.3 mm 2.22 in 2.22 in SWDC+ N.O. 61.7 mm 55.9 mm 61.7 mm 55.9 mm 2.43 in 2.20 in SWDC-...
81.8 mm 94.7 mm (3.22 in) (3.73 in) To install or remove, 78.1 mm 90.7 mm press down here. (3.08 in) (3.57 in) See Installing/ Removing 80.0 mm 39.1 mm (1.54 in) the DIN Rail Controller (3.07 in) Part Number Label procedures below.
Page 6
72.4 mm 68.0 mm (2.85 in) (2.68 in) Panel Cutout 72.4 mm Panel Thickness (2.85 in) 68.0 mm 1.52 to 3.18 mm (2.68 in) (0.060 to 0.125 in) 19.1 mm (0.75 in) minimum 19.1 mm (0.75 in) minimum Spade Terminal Model Customer Front Panel Part Number Label 84.5 mm square...
Page 7
2. Insert the controller into the panel cutout. 3. While pressing the bezel firmly against the panel, slide the mounting bracket over the back of the con- troller. Be sure the levers on the mounting bracket line up with the teeth on the case. 4.
Wiring The terminals on the back of the Series C and Series TM controllers are Ó the same for all of the package styles. They are 6.3 mm (0.25 in) quick connect, push on style terminals or removable screw terminal block. The terminal style Warning: is an ordering option.
Page 9
AC Power Wiring Figure 7a — ç • Nominal voltage options: - 24VÅ (ac) Warning: Use National Electric (NEC) or - 120VÅ (ac) other country-specific standard - 230 to 240VÅ (ac) wiring and safety practices when wiring and connecting this con- troller to a power source and to electrical sensors or peripheral devices.
Page 10
Switched DC Output Figure 8a — ç • Maximum voltage output into an infinite load, 24VÎ (dc) Warning: • Minimum output voltage at 10 mA, 5VÎ (dc) Use National Electric (NEC) • Minimum load impedance, 500Ω or other country-specific • Offstate leakage, 100μAÎ (dc) standard wiring and safety •...
System Wiring Examples Power Disconnect Switch 120V~(ac) High- Customer Fuse Fuse Supplied Temp. Quencharc Light Fuse High Limit Fuse Mechanical coil Contactor Not used SWDC+ SWDC Reset Switch (customer supplied) SW-1 N.O. SW-2 SSR-240-10A-DC1 in out N.C. Solid-State Relay Series CV Temperature Controller Heater CVB1JH00000100C...
User Interface Variable Set Point, Standard CV _ _ (1, 2, 5 or 6) _ _ _ _ _ _ _ _ _ A F or C Indicator Light: Lit to indicate if unit is configured for degrees Fahrenheit or LED Display: Indicates degrees Celsius.
Page 13
Variable Set Point, Push for Process CV _ (1, 2, 5 or 6) _ _ _ _ _ _ _ _ _ _ B F or C Indicator Light: Lit to indicate if unit is configured for degrees Fahrenheit or degrees Celsius.
Page 14
Variable Set Point, Push to Set CV _ (1, 2, 5 or 6) _ _ _ _ _ _ _ _ _ _ C F or C Indicator Light: Lit to indicate if unit is configured for degrees Fahrenheit or LED Display: Indicates degrees Celsius.
Page 15
Variable Set Point, Push to Set CV _ (1, 2, 5 or 6) _ _ _ _ _ _ _ _ _ _ D F or C Indicator Light: Lit to indicate if unit is configured for degrees Fahrenheit or LED Display: Indicates degrees Celsius.
Temperature Indicator TM _ _ _ _ _ _ _ _ _ _ _ _ _ F or C Indicator Light: Lit to indicate if unit is configured for degrees Fahrenheit or LED Display: Indicates degrees Celsius. the process value. Figure 14 —...
Troubleshooting Indication Probable Cause(s) Corrective Action On indicating controls, the • Power supply switch off. • Turn switch on. display is not illuminated. • Fuse blown. • Replace fuse (check cause of failure). • Breaker tripped. • Reset breaker (check cause of failure). •...
Page 18
Indication Probable Cause(s) Corrective Action Troubleshooting RTD inputs Temperature reading is in- • Calibration offset incorrect (tactile Check calibration offset correct, showing a sensor er- models only). ror, [Er; I n] , or LOAD LED • Settings for degree C or F is incorrect. Check model part number for degree C or F. is switching at the wrong If model has Increment/Decrement keys then temperature.
Specifications Controller Output Types • Microprocessor based, on-off control mode. Switched DC (non-isolated) • Nominal switching hysteresis, typically 1.7°C (3°F). • Supply voltage maximum: 24V (dc) into an infinite load. Î • Input filter time: 1 second • Supply voltage minimum: 5V (dc) at 10 mA Î...
Page 20
Ordering Information and Model Numbers On-off controller, No user interface _ _ _ _ _ _ _ _ A A A A Set Point Type Fixed Set Point Line Voltage and Output 120VÅ (ac), Switched DC Output 120VÅ (ac), 8 Amp Relay Output 230 to 240VÅ...
Page 21
Ordering Information and Model Numbers On-off controller, LED Display _ _ _ _ _ _ _ _ _ _ _ _ Set Point Type Variable Set Point Line Voltage and Output 120VÅ (ac), Switched DC Output 120VÅ (ac), 8 Amp Relay Output 230 to 240VÅ...
Page 22
Ordering Information and Model Numbers Temperature Indicator _ _ _ A A A A A A A A A Line Voltage and Output 120VÅ (ac) 230 to 240VÅ (ac) 24VÅ (ac) Controller Package Panel Mount, 1/8 DIN Square -Spade Terminals DIN Rail Mount -Spade Terminals Panel Mount, 1/8 DIN Square -Screw Terminals DIN Rail Mount -Screw Terminals...
Page 23
Declaration of Conformity Series C and Series TM Watlow Winona, Inc. 1241 Bundy Blvd. Winona, MN 55987 USA Declares that the following product: Designation: Series C and Series TM Model Numbers: CF – (B, C, D, E, F or G)(1, 2, 3 ,4, 5, 6 or 7)(any letter)(H or C) – (any four numbers or –...
Page 24
Declaration of Conformity Raymond D. Feller III Winona, Minnesota, USA Name of Authorized Representative Place of Issue General Manager February 2008 Title of Authorized Representative Date of Issue Signature of Authorized Representative Buy: www.ValinOnline.com | Phone: 844-385-3099 | Email: CustomerService@valin.com...
Page 25
How to Reach Us Corporate Headquarters Europe Watlow Electric Manufacturing Company Watlow France SARL Watlow Ibérica, S.L.U. 12001 Lackland Road Immeuble Somag CME - Avda. de la Vía Láctea, s/n. Oficina 24 St. Louis, MO 63146 16, Rue Ampère 28830 - San Fernando de Henares Madrid Sales: 1-800-WATLOW2 95307 Cergy-Pontoise CEDEX Spain...