1. Manuals
  2. Brands
  3. Tarsacci Manuals
  4. Metal Detector
  5. MDT 8000
  6. User manual

Tarsacci MDT 8000 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

U s e r M a n u a l
M D T 8 0 0 0
| 1
User
Manual
MDT 8000

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MDT 8000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Tarsacci MDT 8000

  • Page 1 U s e r M a n u a l M D T 8 0 0 0 User Manual MDT 8000...

  • Page 2: Table Of Contents

    U s e r M a n u a l M D T 8 0 0 0 Contents 1. ASSEMBLY ..................................3 2. CONTROL PANEL................................8 3. DISPLAY ................................... 9 4. METAL DETECTOR MODES AND SETTINGS ........................10 4.1. B S (B ) ..............................

  • Page 3: Assembly

    U s e r M a n u a l M D T 8 0 0 0 Assembly...
  • Page 4 U s e r M a n u a l M D T 8 0 0 0 1. Insert the two rubber washers into the holes on either side of the lower shaft. 2. Slide the lower shaft into the search coil mounting bracket.
  • Page 5 U s e r M a n u a l M D T 8 0 0 0 3. Insert the search coil mounting bolt through the search coil mounting bracket. 4. Fasten the search coil mounting nut. (Do not overtighten the nut)
  • Page 6 U s e r M a n u a l M D T 8 0 0 0 5. Loosen the middle shaft clamp. 6. Insert the lower shaft into the middle shaft. Lock the clamp.
  • Page 7 U s e r M a n u a l M D T 8 0 0 0 7. Loosen the upper shaft clamp. 8. Insert the middle shaft into the upper shaft. Lock the clamp. 9. Connect the coil cable connector to the control housing coil connector and tighten the retaining ring.

  • Page 8: Control Panel

    U s e r M a n u a l M D T 8 0 0 0 Control Panel MODE Button Plus Arrow Button If the cursor highlights the BlkS or St/Salt icons, the MODE button activates or Increment the setting icon highlighted by deactivates black sand or salt mode.

  • Page 9: Display

    U s e r M a n u a l M D T 8 0 0 0 Display St/Salt Salinity range 0 to 50. BlkS (Black Sand) Track (Tracking) Frequency select displays the current When it is deactivated, it will display operating frequency.

  • Page 10: Metal Detector Modes And Settings

    U s e r M a n u a l M D T 8 0 0 0 | 10 Metal Detector Modes and Settings BlkS (Black Sand): To activate Black Sand Mode: 1. Press and release the “TS” button until the cursor highlight’s “BlkS” icon. Figure 1: The BlkS icon is highlighted 2.

  • Page 11: Track

    U s e r M a n u a l M D T 8 0 0 0 | 11 Track: To activate or deactivate Tracking mode: 1. Press and hold the “TS” button for more than 3 seconds. Figure 5: Tracking is activated Fc: To change the Frequency: 1.

  • Page 12: Sens

    U s e r M a n u a l M D T 8 0 0 0 | 12 Sens: To adjust the Sensitivity: 1. Press and release the “Menu” button until the cursor highlights the “Sens” icon. Figure 9: Sensitivity is highlighted and can be adjusted 2.

  • Page 13: Vol

    U s e r M a n u a l M D T 8 0 0 0 | 13 Vol: To adjust the Volume: 1. If one of the settings is activated, and idling for more than 8 seconds, the cursor will automatically highlight Volume.

  • Page 14: Pin Point Procedure

    | 14 Pin Point Procedure: MDT 8000 metal detector has a Double–D search coil configuration. The search coil’s most sensitive area is along the search coil longitudinal centerline. The metal detector will give the loudest response when a target is directly beneath it.

  • Page 15: Target Id And Sound Modes

    U s e r M a n u a l M D T 8 0 0 0 | 15 Target ID and Sound Modes Numerical Target ID Display: Represents the Target conductivity and is always displayed. Non-ferrous Targets have positive numbers and ferrous Targets have negative numbers. The target ID number range is from -30 to +30 and is a function of the target’s shape, thickness and the metal conductivity.

  • Page 16: Discrimination Breakdown Visuals

    U s e r M a n u a l M D T 8 0 0 0 | 16 Discrimination Breakdown Visuals The following figures give a visual breakdown of Discrimination sounds related to the Target ID numbers.  -30 to 0 = Low Tone, ferrous Target ...

  • Page 17: Manual Ground Balance

    U s e r M a n u a l M D T 8 0 0 0 | 17 Manual Ground Balance The metal detector ground balance has to be done on ground free of any metals; otherwise, the ground balance will be incorrect if done while a metal is present.

  • Page 18: Auto Ground Balance Procedure

    U s e r M a n u a l M D T 8 0 0 0 | 18 Auto Ground Balance Procedure The metal detector ground balance has to be done on ground free of any metals; otherwise, the ground balance will be incorrect if done while a metal is present.

  • Page 19: Salinity Balance

    U s e r M a n u a l M D T 8 0 0 0 | 19 Salinity Balance (This Process is similar to the manual ground balance) 1. Ground Balance the metal detector on the dry side of the beach with Salt Mode activated. (If the beach is not mineralized, like white sand beaches, ground balance is not necessary and manually set the ground balance to 500.) 2.

  • Page 20: Threshold

    U s e r M a n u a l M D T 8 0 0 0 | 20 Threshold Threshold ranges from -9 up to 0. All positive target response signals are audible. When using a negative threshold, the value is subtracted from the target signal. A Threshold of zero does not affect the signal. To increase the ability to hear faint signals, it is recommended to set the TrH to -1 or 0.

  • Page 21: Suggested Settings For Stable Metal Detector Work

    U s e r M a n u a l M D T 8 0 0 0 | 21 Suggested Settings for Stable Metal Detector Work Suggested Settings for mineralized (black sand) salt water beach  Set the threshold to -2. ...

  • Page 22: Specification

    Weight : 1280g (2.82lb) including the battery Waterproof : IP68 (Up to 1.5 meters for up to 30 minutes). Headphones (Included) : Wired 3.5mm non-waterproof Tarsacci reserves the right to change the design, equipment, and technical features at any time...

Table of Contents