OmniPower Power Caddy III Instruction Manual

Self-contained power system

Advertisement

Quick Links

POWER CADDY
POWER
Model:
Instruction Manual for:
POWERCADDYIII
Model: B: Power Caddy III
Instruction Manual for:
Self-Contained Power System
Version 09
CADDY
B:
Power
1
Caddy
III
III

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Power Caddy III and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for OmniPower Power Caddy III

  • Page 1 POWER CADDY POWERCADDYIII Model: B: Power Caddy III Instruction Manual for: Self-Contained Power System Version 09 POWER CADDY Model: Power Caddy Instruction Manual for:...
  • Page 2: Table Of Contents

    CONTENTS INTRODUCTION ..................3 USING THE POWER CADDY III: ............. 4 CONNECTIONS TO THE POWER CADDY III ......... 6 SWITCHES, & INDICATORS ..............7 TROUBLE-SHOOTING ................8 PRECAUTIONARY ADVICE ..............8 TECHNICAL SPECIFICATION ..............9 TECHNICAL SPECIFICATIONS CONTINUED ........10 WARRANTY ....................
  • Page 3: Introduction

    This manual describes the simple steps to use the unit and explains the operation of the Power Caddy III so you can understand what you can (and cannot) connect to the unit and what to do if you have a problem.
  • Page 4: Using The Power Caddy Iii

    BATTERY AND MAY VARY WITH ENVIRONMENTAL, BATTERY CHARGE AND LOAD CONDITIONS. BASED ON 800VA WITH 12V 102AH BATTERY. Power Caddy III can power an assortment of appliances covering most of the standard home entertainment and household low power appliances you might want to connect to...
  • Page 5 These items should not be used with the “Power Caddy III” Electric heater Electric stove 2 /4 plate electric hob Iron Hair dryer Electric kettle Toaster Microwave oven Geyser Power tools Vacuum cleaner Air conditioner This list is not exhaustive and should include any items/appliances with similar power...
  • Page 6: Connections To The Power Caddy Iii

    3. CONNECTIONS TO THE POWER CADDY III Supplied with the Power Caddy III is a 3-pin 15A SA cable with a 3-pin ‘G-ST18i connector’. This cable is for the built-in battery charger in the Power Caddy III. Connect this cable to an AC mains wall socket to charge the unit. You should leave the unit permanently connected.
  • Page 7: Switches, & Indicators

    4. SWITCHES, & INDICATORS At this point, you’re ready to start using the Power Caddy III. Step 1 is to connect the Power Caddy III to an AC mains outlet, switch it on to get the battery charged. Note that all our units are shipped to the customer fully charged.
  • Page 8: Trouble-Shooting

    The unit must not be kept or operated in direct sunlight and should never be placed in a moist or wet environment. In the case of overload, the Power Caddy III will need to be reset by switching the unit ON and OFF again.
  • Page 9: Technical Specification

    7. TECHNICAL SPECIFICATION MODEL B: Power Caddy III Inverter: Power Control / Power Assist Transfer Switch 19 – 33V Input Voltage Range Output Voltage and Frequency 230VAC +-2% 50Hz +-0,1% Continuous Output at 25°C (Non-linear load) 800VA Continuous Output at 25°C 700W Continuous Output at 40°C...
  • Page 10: Technical Specifications Continued

    It is the responsibility of the end user or third party to ensure sufficient care is taken to protect the Power Caddy III from incorrect connection and overload when connected to external devices. No claims will be considered where the Power Caddy III is used for applications outside the functional specifications for which it is intended. Severability...
  • Page 11: Annexure 1

    10. ANNEXURE 1 English Manual for MultiPlus 500VA – 1200VA 10.1. GENERAL Multifunctional The Multi gets its name from the multiple functions it can perform. It is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology ana high-speed AC transfer switch in a single enclosure.
  • Page 12: Battery Charger

    10.2. BATTERY CHARGER Adaptive 4-stage charging characteristics: bulk – absorption – float – storage The microprocessor-driven adaptive battery management system can be adjusted for various types of batteries. The adaptive function automatically adapts the charging process to battery use. The right amount of charge: variable absorption time In the event of slight battery discharge, absorption is kept short to prevent overcharging and excessive gas formation.
  • Page 13: Led Indicators

    10.4. LED INDICATORS...

Table of Contents