Table of Contents
Advertisement
Quick Links
A S S E M B LY I N S T R U C T I O N S
Classica Vinyl Mailbox Post with
No-Dig Steel Pipe Anchor Kit
*
*) Mailbox and mounting hardware not included
Please read through before starting assembly.
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 877 234 6196(Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Post Cap (1)
2. Post (1) - 4" x 4" x 56"
3. Post Arm (1) - 5" x 5" x 25½"
4. Post Trim Cap (1)
5. Anchor Pipe (1) - 46¾"
6. Base Molding (1)
7. 1" Self-Auguring Stainless Steel Screw (2)
8. 1 1/4" Self-Auguring Stainless Steel Screw (5)
Tools You Will Need
• Cordless Drill
• Level
• Sledge Hammer
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5'x 8' for unobstructed assembling.
• You should not need to use excessive force when assembling components.
3 3/8 in
56 5/8 in
42 in
8 in
1
2
3
4
7
8
5
Not to Scale
6
Zippity
DO-IT-YOURSELF
FRIENDLY PRODUCTS
19 in
22 3/4 in
Ground
24 in
Ver 1.0/121915
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Zippity Classica Vinyl Mailbox Post
Summary of Contents for Zippity Classica Vinyl Mailbox Post
- Page 1 A S S E M B LY I N S T R U C T I O N S Classica Vinyl Mailbox Post with Zippity DO-IT-YOURSELF No-Dig Steel Pipe Anchor Kit FRIENDLY PRODUCTS 19 in 3 3/8 in 56 5/8 in...
- Page 2 Slide trim cap into position under arm as illustrated. Install a 1 1/4” screw as illustrated beneath trim cap. This will prevent trim cap from sliding down the post. Zippity DO-IT-YOURSELF FRIENDLY PRODUCTS C l a s s i c a Vi n y l M a i l b o x P o s t I n s t r u c t i o n...
- Page 3 10lb Sledgehammer BETTER ±21 5/8 in 5lb Sledgehammer Zippity Hammer DO-IT-YOURSELF FRIENDLY PRODUCTS C l a s s i c a Vi n y l M a i l b o x P o s t I n s t r u c t i o n...
- Page 4 S T E P T W O Install Pipe (Continued) Adjust bottom and top donuts into level to compensate for crooked pipe. Slide assembled vinyl post down over donuts as per the next step. Adjust bottom and top donuts to Install vinyl post over donuts.
- Page 5 Orient vinyl post correctly and slide the assembled mailbox post over the pipe and down into the ground at least 3” Slide the base moulding down to the ground as illustrated. Zippity DO-IT-YOURSELF FRIENDLY PRODUCTS C l a s s i c a Vi n y l M a i l b o x P o s t I n s t r u c t i o n...
- Page 6 S T E P T H R E E Install Mailbox over Pipe (Continued) Zippity Fasten 2, 1” screws through the back of the mailbox post as shown. DO-IT-YOURSELF FRIENDLY PRODUCTS Screw should be approximately 21 5/8” from the ground as per Step 3 on page 3 and 1/2”...
Need help?
Do you have a question about the Classica Vinyl Mailbox Post and is the answer not in the manual?
Questions and answers