Limited Warranty; Tool Specifications; Fastener Specifications - DeWalt DWFP12569 Instruction Manual

English
D WALT tools are precision-built tools, designed for precise,
e
high volume nailing. These tools will deliver efficient,
dependable service when used correctly and with care.
As with any fine power tool, for best performance the
manufacturer's instructions must be followed. Please study
this manual before operating the tool and understand
the safety warnings and cautions. The instructions on
installation, operation and maintenance should be read
carefully, and the manual kept for reference.
nOTE: Additional safety measures may be required because
of your particular application of the tool. Contact your
D WALT representative or distributor with any questions
e
concerning the tool and its use.
D WALT, 701 E. Joppa Road, Towson, Maryland 21286,
e
U.S. & Canada Only, É.-U. et Canada seulement
D WALT tools have been engineered to provide excellent
e
customer satisfaction and are designed to achieve
maximum performance when used with precision D
fasteners engineered to the same exacting standards.
D WALT cannot assume responsibility for product
e
performance if our tools are used with fasteners or
accessories not meeting the specific requirements
established for genuine D
e
and accessories.

Limited Warranty

U.s. and Canada Only
D WALT warrants to the original retail purchaser that the
e
product purchased is free from defects in material and
workmanship, and agrees to repair or replace, at D
option, any defective D WALT branded pneumatic stapler or
e
nailer for a period of seven (7) years from date of purchase
(one (1) year from the date of purchase for compressors
2-N-1™ FLOORING TOOL: DWFP12569

Tool specifications

Model Length Height
DWFP12569 20.39" (518 mm)21.95" (558 mm) 3.15" (80 mm) 10.2 lbs (4.6 kg)
All dimentions in inches unless otherwise specified.

Fastener specifications

Model Fastener Crown
Width
1/2"
DWFP12569 DWCS15xx
(13mm)
DWFP12569 DWFLN-xxx -
2
WALT
e
WALT nails, staples
WALT's
e
Width Weight
Gauge Fastener Range
15-1/2 Ga., 1/2" 1-1/2" (38mm)
Crown Staples to 2" (50mm)
16 Ga. "L" shape 1-1/2" (38mm)
Cleat Nails to 2" (50mm)
and tools used in production applications). Warranty is not
transferable. Proof of purchase date required. This warranty
covers only damage resulting from defects in material or
workmanship; it does not cover conditions or malfunctions
resulting from normal wear, neglect, abuse, accident or
repairs attempted or made by other than our national repair
center or authorized warranty service centers. Driver blades,
bumpers, o-rings, pistons and piston rings are considered
normally wearing parts. For optimal performance of your
D WALT tool always use genuine D
e
replacement parts.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. D
SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
Some states and countries do not allow limitations on how
long an implied warranty lasts, or the exclusion or limitation
of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have other
rights which vary from state to state and country to country.
To obtain warranty service in the U.S. return the
product, together with proof of purchase, to the U.S.
D WALT National or Regional Independent Authorized
e
Warranty Service Center. In the U.S. you may call us at
1-800-4-D WALT (1-800-433-9258) or visit www.D
e
com for the location most convenient for you. In Canada
please call us at 1-800-4-D WALT (1-800-433-9258) or visit
e
www.D WALT.com
e
Tool Air Fitting:
This tool uses a 1/4" N.P.T. male plug. The inside diameter
should be .200" (5 mm) or larger. The fitting must be
capable of discharging tool air pressure when disconnected
from the air supply.
Operating Pressure:
70 to 100 p.s.i.g. (4.9 to 7.0 kg/cm²). Select the
operating pressure within this range for best fastener
performance. DO NOT EXCEED THIS RECOMMENDED
OPERATING PRESSURE.
Air Consumption:
The DWFP12569 requires 3.52 cubic feet per minute
(100 liters per minute) of free air to operate at the rate of
60 fasteners per minute, at 80 p.s.i. (5.6 kg/cm2). Take the
actual rate at which the tool will be run to determine the
amount of air required. For instance, if your fastener usage
averages 30 fasteners per minute, you need 50% of the
tool's c.f.m. of free air which is required to operate the tool
at 60 fasteners per minute.
WALT fasteners and
e
WALT
e
WALT.
e