Related Manuals for Aneng Q1
Summary of Contents for Aneng Q1
- Page 1 User Manual All rights reserved. Specifications are subject to change without notice.
-
Page 2: Limited Warranty
LIMITED WARRANTY AND LIMITATION OF LIABILITY Customers enjoy one-year warranty from the date of purchase. This warranty does not cover fuses, disposable batteries, damage from misuse accident, neglect, alteration, contamination, or abnormal conditions of operation or handling, including failures caused by use outside of the product's specifications, or normal wear and tear of mechanical components. -
Page 3: Table Of Contents
Table of Contents Page Introduction............1 Safety Information..........1 Instrument Overview..........3 LCD Display...........3 Function Buttons..........5 Input Terminals..........8 Measurements Instruction........9 Measure AC/DC Voltage.........9 Measure AC/DC Current.........9 Measure Resistance........10 Test Diodes and Continuity......11 Measure Capacitance........11 Measure Frequency and Duty Cycle.....12 Measure Temperature........13 Test NCV…………..…………………………14... - Page 4 Maintenance............15 Clean the Product.........15 Replace the Batteries........15 Replace the Fuses........16 Specifications.............17 General Specifications.........17 Mechanical Specifications......17 Environmental Specifications.......17 Electrical Specifications........18...
-
Page 5: Introduction
Introduction This product is a 9999 counts true RMS auto- ranging digital multimeter. It is operated all by buttons with a triple display. Safety Information To avoid possible electrical shock, fire, or personal injury, please read all safety information before you use the product. Please use the product only as specified, or the protection supplied by the product can be compromised. - Page 6 • Keep fingers behind the finger guards on the probes. • When the product has already been connected to the line being measured, do NOT touch the input terminal that is not in service. • Disconnect the test leads from the circuit before changing the mode.
-
Page 7: Instrument Overview
Instrument Overview LCD Display ① ② ③ ④ ⑤⑥ ⑦ ⑧ ⑨ ㉔ ⑩ ㉓ ⑪ ㉒ ⑫ ㉑ ⑬ ⑳ ⑭ ⑲ ⑯ ⑮ ⑰ ⑱ Auto range. The product selects ① the range with the best resolution. Manual range. The user selects ②... - Page 8 ⑪ Frequency test. (Hertz) ⑫ Temperature test. (Celsius) ⑬ Temperature test. (Fahrenheit) ⑭ Analog bar graph. ⑮ Resistance test. (Ohm) ⑯ Current test. (Ampere) ⑰ Voltage test. (Volt) ⑱ Primary measurement display. product measures both ⑲ sinusoidal and nonsinusoidal ac waveforms accurately.
-
Page 9: Function Buttons
Function Buttons ② ① ⑥ ③ ⑦ ④ ⑤ Push for more than 2 seconds to turn on/off the product. • The product automatically powers off after 5 minutes of inactivity. • The built-in beeper beeps 5 times 1 minute before auto power off. - Page 10 Push once to hold the current reading on the display; push again continue normal operation. Push for more than 2 seconds to enter the ② relative mode. The product will store the present reading as a reference for subsequent readings. The display is zeroed, and the stored reading is subtracted from all subsequent readings.
- Page 11 Push this button when the product is at the setting of ACV, the primary measurement display will show the current frequency (1~100kHz) while the secondary measurement display will show the current duty cycle. ⑦ Push this button when the product is at the setting of ACmV, the primary measurement display will show the current frequency (1~5MHz) while the secondary measurement...
-
Page 12: Input Terminals
Input Terminals Input terminal AC/DC current A mA measurements to 9.999A. Input terminal AC/DC current μA measurements to 999.9μA. Common (return) terminal measurements. Input terminal for the measurements of: 1. AC/DC voltage 2. Resistance 3. Capacitance VΩHz 4. Frequency 5. Temperature 6. -
Page 13: Measurements Instruction
Measurements Instruction Measure AC/DC Voltage 1. Connect the black test lead to the COM Terminal and the red lead to the VΩHz Terminal. 2. To measure voltage under 99.99mV, push push once to measure DCmV, push twice to measure ACmV. To measure voltage higher than 99.99mV, push , push once to measure DCV, push twice to measure ACV. -
Page 14: Measure Resistance
2. Push to toggle between DCA and ACA. 3. Break the circuit path to be measured, connect the test leads across the break and apply power. 4. Read the measured current on the display. *Do not measure current that exceeds the extremes as indicated in the Specifications. -
Page 15: Test Diodes And Continuity
Test Diodes and Continuity 1. Connect the black test lead to the COM Terminal and the red lead to the VΩHz Terminal. 2. Push twice to enter the Diode/Continuity Mode. 3. To test continuity, touch the probes to the desired test points of the circuit. The built-in beeper will beep when there is a short circuit. -
Page 16: Measure Frequency And Duty Cycle
2. Push three times to enter the Capacitance Mode. 3. Connect the red probe to the anode side and the black probe to the cathode side of the capacitor being tested. 4. Read the measured capacitance value on the display once the reading is stablized. *Disconnect circuit power and discharge all capacitors before you test capacitance. -
Page 17: Measure Temperature
3. When the frequency to be measured is between 100kHz and 500MHz, push twice to enter the ACmV Mode; touch the probes to the desired test points, and the secondary measurement display will show the frequency; then push , the primary measurement display will show... -
Page 18: Test Ncv
2. Touch the probes to the desired test points. 3. Read the measured temperature on the display. Test NCV 1. Push twice to enter the NCV Mode. 2. Hold the product and move it around, the built- in beeper will beep when the inner sensor detects AC voltage nearby. -
Page 19: Maintenance
Maintenance Beyond replacing batteries and fuses, do not attempt to repair or service the product unless you are qualified to do so and have the relevant calibration, performance test, service instructions. Clean the Product Wipe the product with a damp cloth and mild detergent. -
Page 20: Replace The Fuses
2. Loosen the screw on the battery door and remove the battery door. 3. Replace the used batteries with new batteries of the same type. 4. Place the battery door back and fasten the screw. Replace the Fuses When a fuse is blown or do not work properly, it shall be replaced as below: 1. -
Page 21: Specifications
Specifications General Specifications 9999 Counts Display（LCD） Ranging Auto/Manual Material ABS+TPE Update Rate 3 Times/Second Ture RMS √ Data Hold √ Backlight √ Low Battery Indication √ Auto Power Off √ Mechanical Specifications Dimension 146*74*34mm Weight 125g Battery Type 1.5V AA Battery * 2 Warranty One year Environmental Specifications... -
Page 22: Electrical Specifications
Electrical Specifications Function Range Resolution Accuracy 999.9mV 0.1mV 9.999V 0.001V DC Voltage 99.99V 0.01V ±(0.5%+3) 999.9V 0.1V 9.999mV 0.001mV DC Voltage (mV) 99.99mV 0.01mV 999.9mV 0.1mV 9.999V 0.001V AC Voltage 99.99V 0.01V ±(1.0%+3) 750.0V 0.1V 9.999mV 0.001mV AC Voltage (mV) 99.99mV 0.01mV *Frequency response of ACV: 40Hz-1kHz... - Page 23 Function Range Resolution Accuracy 999.9mA 0.1mA DC Current ±(1.0%+3) (mA&A) 9.999A 0.001A 99.99μA 0.01μA DC Current ±(0.8%+3) (μA) 999.9μA 0.1μA 999.9mA 0.1mA AC Current ±(1.2%+3) (mA&A) 9.999A 0.001A 99.99μA 0.01μA AC Current ±(1.0%+3) (μA) 999.9μA 0.1μA Frequency response of AC Current: 40Hz-1kHz 99.99Ω...
- Page 24 Function Range Resolution Accuracy 9.999nF 0.001nF ±(5.0%+20) 99.99nF 0.01nF 999.9nF 0.1nF Capacitance 9.999μF 0.001μF ±(2.0%+5) 99.99μF 0.01μF 999.9μF 0.1μF 9.999mF 0.001mF ±(5.0%+5) 99.99Hz 0.01Hz Frequency 999.9Hz 0.1Hz (Measures 9.999kHz 0.001kHz only to ±(0.1%+2) 100kHz 99.99kHz 0.01kHz under the 999.9kHz 0.1kHz ACV setting) 5.000MHz 0.001MHz...
- Page 25 Function Range Resolution Accuracy (-20~1000)℃ 1℃ Temperature ±(2.5%+5） (-4~1832)℉ 1℉ Diode √ Continuity √ √...