Subscribe to Our Youtube Channel
Related Manuals for Trox X-AIRCONTROL
Summary of Contents for Trox X-AIRCONTROL
- Page 1 COMISSIONING OJ GreenZone™ Stand-alone English Commisioning Guide X-AIRCONTROL Stand-alone • English...
-
Page 2: Table Of Contents
All versions use Modbus to communicate with the Room Panel. MOUNTING Mounting the X-AIRCONTROL Zone Module The X-AIRCONTROL Zone Module is designed to be mounted on a DIN rail. Avoid direct exposure to sunlight. After initial setup, there is no need for physical access to the X-AIRCONTROL Zone Module and the unit can therefore be mounted in concealed locations. -
Page 3: Mounting The X-Aircontrol Room Panel
X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen the X-AIRCONTROL Zone Module to the Room Panel must not RJ12 Description exceed 50 m (164 ft) in length. +24V Mounting the X-AIRCONTROL Room Panel The Room Panel is designed for flush mounting in a hollow wall box. -
Page 4: Configuration
Room Panel menus The various menus of the X-AIRCONTROL Room Panel are accessed by tapping the menu icon in the upper right corner of the screen. If the It is possible to define work days and home days. As default,... -
Page 5: Room Data
X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen Room data Settings menu In the Room data menu, you can see the current sensor readings. Tap the Down arrow at the bottom of the main menu. -
Page 6: Date/Format
X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen After changing the date, tap the Left arrow to go back to the main menu. In the main menu, tap Home to exit the menu. -
Page 7: Override Timeout
X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen Override timeout Menu hide When the schedule is overridden, the system will revert to the The menu icon on the Home screen can be hidden from users by schedule after a given time has elapsed. -
Page 8: Frost/Window
X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen Air volume Frost/Window Air volume can be set to Off, Low, High or Auto. Air volume is Terminals 14 and 15 on the Zone Module can be used either for adjusted in per cent of VAV damper performance. - Page 9 X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen Screen saver Config mode After a given time without activity, the display will switch to a When Config mode is set to Auto, the system will continuously black screen displaying only the time and temperature setting.
- Page 10 PI regulator button. Choose either P-band or I-time by tapping the respective button. The value shown under P-band is the X-AIRCONTROL default value. The minimum P-band value is 1° Kelvin and the maximum value is 10° Kelvin. Settings can be chosen in steps of 1° Kelvin.
-
Page 11: Alarm List
X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen About ALARMS Tap the About button to open the information screen. When an alarm is active, an alarm icon will appear on the right side of the Home screen. - Page 12 X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen X-AIRCONTROL Zone Module and Room Panel with 2” Touchscreen Alarm no. Description Troubleshooting Inlet temperature sensor Check the inlet temperature sensor removed and the signal on the “Room °C” Check the power supply to the X-...
- Page 13 INBETRIEBNAHME OJ GreenZone™ Stand-alone Deutsch TROX Auranor Norge AS PO Box 100 Telephone +47 61 31 35 00 Fax +47 61 31 35 10 e.mail: firmapost@auranor.no www.trox.no...
Need help?
Do you have a question about the X-AIRCONTROL and is the answer not in the manual?
Questions and answers