Download Print this page
Hide thumbs Also See for VS-LC102:

Advertisement

Quick Links

1 Preparation before use
▼ Very Important
 Please activate your warranty:
 To download the updated software, multilingual manuals, and Quick Start Guide, please
visit Lumens™ web site at:
 To ensure successful installation, please be sure to follow each of the following steps
1.1 Equipment requirements
VS-LC102 x 1
IP PTZ camera x 1 ~ 3, e.g. VC-A20P x 3
Computer (or Laptop) x 1
Router x 1, Giga router recommended
Display x 1
Network cables x 3 ~ 5
HDMI or VGA cable x 2
Amplifier x 1
Audio mixer x 1
Speaker set x 1
Mic x 1
[Remark] The number of connected devices can be increased or adjusted based on
environment requirements.
http://www.MyLumens.com/reg
http://www.MyLumens.com/support.php
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the VS-LC102 and is the answer not in the manual?

Questions and answers

Summary of Contents for Lumens VS-LC102

  • Page 1  Please activate your warranty: http://www.MyLumens.com/reg  To download the updated software, multilingual manuals, and Quick Start Guide, please visit Lumens™ web site at: http://www.MyLumens.com/support.php  To ensure successful installation, please be sure to follow each of the following steps 1.1 Equipment requirements...
  • Page 2: How To Connect

    Device Connect the WAN port to the router to link with the computer in order to conduct remote management of VS-LC102 Note: Please first connect the computer to a LAN port (8), and then connect the computer to a router after completion of the external network setting Networking Connect webcam (e.g.
  • Page 3 OSD menu. C-Video Cable DVI cable Monitor or HDTV [Remark] For VC-A20P relevant use and operation method, please visit Lumens website; download and read the VC-A20P operation manual.  Before begin the following settings, please confirm that the connection has been...
  • Page 4 3.3 Connect to the VS-LC102 Webpage (including log in) [Remark 1] For the computer that remotely controls VS-LC102, the network interface card needs to be set to obtain the IP address automatically.  Use the computer being connected to LAN, and open a web browser ...
  • Page 5  Open the [Network Setting] page  Select [DHCP]  Click [Apply] to apply the setting  Reconnect after confirming the VS-LC102 IP address according to [Remark] Upon completion of the setting, the computer can be connected remotely via the LAN 3.4.3 Format a hard drive...
  • Page 6  Select a hard drive. For the initial use, please format the hard drive first. It takes few minutes to format the hard drive and the duration varies according to different storage device formats. Before the formatting is completed, please do not close the webpage.
  • Page 7  Press [Submit] and wait until the state of the webcam is 3.4.5 Setup the image input    Click [Video Source] page. Set the video sources of CH1 、 CH2 、 CH3 、 CH4  CH1: Click [Channel1]; select [Computer] from the channel name; set image as [Video Port];...
  • Page 8 3.4.6 Audio In  Audio Volume  Select sound output according to the output device ([Remark] HDMI output is preferred)  Press [Apply] to apply the setting. [Remark] When Line In is connected to a microphone, please click to change to microphone input.
  • Page 9 If the above function can be performed normally, then the installation is completed. The user can begin the operation remotely via the Internet connection Use of the operational functions or detailed descriptions of various settings and functions of VS-LC102, please refer to Lumens website; download and read the VS-LC102 User Manual.
  • Page 10: Product Overview

    4 Product Overview 4.1 Host Computer Front Panel Description NO. Name Function Descriptions Remote IR Receiver sensor Indicator Record / Power Function Record / Play / Pause / Stop / Menu / Channel / Split Display keyboard shortcuts Operation Up / Down / Left / Right / Return / OK selection key Power button Power Switch...
  • Page 11 5 Remote control brief description NO. Icon Name Function Descriptions Power Turn on / off.  Play Play the video. Press again while playing, the video will pause. Previous / Previous / Next video while playing. Next Video During recording, switch between recording image version type configurations.