Advertisement
ONE
QR TWO THREADS
\
1
PROTRUDI
NG
ABOVE
THE RECTANGULAR
NUT
)/
o
-
RECTANGU LAR
B
NUT
I
Photo
5-14
:
The
correct
distan ce to
unscr ew the
Forward
Clutch
Rod-one or
two threads above
the
rectangular
nut.
3.
Remove
the
belt cover.
4.
S
lip
the forw ard driv e
be
lt
off
t
he
en
gin e-
driven
pulley
by
pushing
it off
with
your
left hand
wh
ile
pull
ing
the
engine
sta rter
rope
with your
right
hand (pulling on the
starter
rope makes the
pulley
turn,
aiding
you
in removing the
belt).
Photo
5-15:
Slipping the
Forward
Drive Belt
off
the
engine-driven pulley
5. On the LEFT
side
of the tiller (as viewed from
the operato
r's
pos
ition)
remove the hairpin cotter
from the clevis pin that connects the forwa
rd
idler
arm to the forward
adjustable link.
'FORWARD
l
aLER
ARM
Photo 5
-16 :
Removing the Clevis Pin from the
Forward
Idler
Arm.
40
6.
Push inward
on the forward idler
arm and
re-
move the
clevis pin.
7. Note the two
holes
in the forwa
rd
adjustable
link.
Push
inward
on
the forw
ard idler.arm and in-
stall
the
clevis pin
through the
inside
hole
in the
fo
rwa rd
ad
ju
stab le
link
and
bac
k throug h
the
hole in the idler
arm.
Secu
re
the clevis
pin
with
the hairpin
cotter.
IMPO RTANT
While
pushing
inward on the forward idler
arm,
make
certain
that the forward drive belt is
pushed off to the
right-hand side
of the
tiller.
This
creates more room to
install
the clevis
pin
whe
n
you push the
forward
idler
arm
inward.
8.
Place
the forward
drive belt in the groove s of
both
the
engine drive pulley
and the transmis -
sion
pulley.
Be
sure
the forw ard
drive
belt
is to
the
inside of the metal
belt guide (on
the
right-
hand
side
of the
tiller).
Also-be
sure
the
forward
drive belt
is to
the
inside of
the
forward
drive
idler
pulley
(on the
left-hand
side
of
the
tiller)
.
~
WIRE Ee RM
BEI!1i
GUID
E
9.
Readjust
the forward drive belt tension by fol-
lowing the instructions in "Handlebar Height
Adjustment"
in Section
3.
10
.
Reinstall
the belt cover and secu
re it
in place
with the
two
nuts.
IMPORTAN T
With
the
clevis
pin
installed in the
inner
hole
in
the forward
adjustable
link,
you
wi
ll
be limited
in
th
e
num
ber
of
future be
lt
tensi on
adjust-
ments
you can
make.
When the
time
comes,
in
future be
lt
ten sio n
adjustments , th
at yo
u
can
not
screw the
Forward
Clutc
h
Rod any
farther into the rectangular
nut
in
the
Forward
Clutch
bracket
,
you must replace the forward
drive
belt. Before
installing a new
belt, be
sure
to return the clevis pin to the ou
tside
hole in
the adjustable
link.
Advertisement
