1. Manuals
  2. Brands
  3. NeuraLabel Manuals
  4. Printer Accessories
  5. 300x NoTouch
  6. User manual

NeuraLabel 300x NoTouch User Manual

Hide thumbs Also See for 300x NoTouch:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
NeuraLabel 300x NoTouch
User Guide
September 2018

Advertisement

Table of Contents
loading

Related Manuals for NeuraLabel 300x NoTouch

Summary of Contents for NeuraLabel 300x NoTouch

  • Page 1 NeuraLabel 300x NoTouch User Guide September 2018...

  • Page 3: Table Of Contents

    NeuraLabel 300x NoTouch Printing System Contents 300x NoTouch System Components ......................1 Setting up the 300x NoTouch System ...................... 2 Loading Media onto the NoTouch ......................5 300x NoTouch Supported Configurations ....................8 Loading the NeuraLabel 300x Standard ....................8 Loading the NeuraLabel 300x CP ......................
  • Page 4 300x NoTouch User Guide...

  • Page 5: 300X Notouch System Components

    NeuraLabel Printing Solutions 300x NoTouch System Components NoTouch Components Base Plate Tower Rails, Datum, and attached Unwinder Sensor Adjustable Flanges Fixed Flanges Four adjustable flanges, two for each winder Two rear flanges Also Included: NoTouch Power Cable; screws to attach Tower to base; Alan Rewinder Sensor key to attach rear flanges to Tower.

  • Page 6: Setting Up The 300X Notouch System

    300x NoTouch User Guide Setting up the 300x NoTouch System See Installation and Quick Start Guide for detailed installation instructions. Before you get started, make sure there is adequate table space for the printing system, including full clearance for the rail system’s extended position.
  • Page 7 NeuraLabel Printing Solutions • The Tower is snug on the base and securely attached. • The Base Plate is on a sturdy table with plenty of clearance on either side. • The Printer fits snugly on the rails with no twisting motion.
  • Page 8 300x NoTouch User Guide NOTE: The set screws tighten into a flat area on the spindle. When resetting, make sure the set screws remain on the flat part. STEP 8. Attach the adjustable flanges. Both the Rewinder and Unwinder have two adjustable flanges that allow you to align the media with the 300x Printer.

  • Page 9: Loading Media Onto The Notouch

    NeuraLabel Printing Solutions Loading Media onto the NoTouch IMPORTANT: The NoTouch unit must be turned OFF whenever you are loading media. The NoTouch uses gesture sensors to control the turning motors. When properly webbed, these motors are actuated by media movement. However, other items may actuate the motors, such as a waving hand, a stray cable, or a piece of paper.
  • Page 10 300x NoTouch User Guide STEP 5. Align the media to the printer guides. Temporarily slide the printer close to the roll unit so that you can correctly align the media. Adjust the gray printer guides so they fit the media width.
  • Page 11 NeuraLabel Printing Solutions STEP 4. Once the flanges are in place and secure, load the media into the printer guides. STEP 5. Check the alignment of the entire system. The entire system, including the Unwinder, 300x Printer, and Rewinder, should be aligned so that the printed media will be straight.

  • Page 12: 300X Notouch Supported Configurations

    There are multiple configurations of the NeuraLabel 300x printer; the NoTouch Roll System works with the NeuraLabel 300x Standard and the NeuraLabel 300x CP. For each of these systems the loading and behavior of the NoTouch is identical. The loading of the printer itself is different for each system.

  • Page 13: Printing

    NeuraLabel Printing Solutions Printing Getting Ready to Print Once you are sure the system is completely set up and aligned, you are ready to print. Make sure the NoTouch Power is turned OFF. STEP 1. Load the media into the 300x Printer. There are three options for loading media: •...

  • Page 14: Printing And Webbing Up On The Fly

    Rewinder Sensor is triggered. This restarts the Rewinder, and the media is automatically rolled. Note that this is the only time a user will need to manually start the 300x NoTouch System. This manual start is necessary so that the user can comfortably web up the media.

  • Page 15: Printing With A Webbed System

    Printing with a Webbed System With the 300x NoTouch System, you can print on a pre-webbed system, meaning the media is already completely through the printer and attached to the rewinder. This allows you to stop printing at any time and at any place in the media roll and resume printing whenever ready.

  • Page 16: Notouch Firmware Updates

    2 flashes, indicates version 3.2. Note that the NoTouch firmware versioning may not be sequential. To update the firmware, obtain the NoTouch Update program from NeuraLabel. • Plug a USB cable into the USB firmware update port on the NoTouch Tower. This is located near the Rewinder Sensor port.

  • Page 17: Notouch Supported Roll Sizes

    Media Width: 1.5” to 8.5” for most media IMPORTANT: For roll width of 3” or less, the 300x Standard Printer requires a special snap-in kit. Contact NeuraLabel for information about the Narrow Media Kit. Remember that 8.5” rolls use the fixed rear flange and one adjustable flange.

  • Page 18: Notouch Rewinder Sensor Calibration

    300x NoTouch User Guide NoTouch Rewinder Sensor Calibration The NoTouch Roll System has a sensor that controls the speed of its rewinder roller. This sensor must be calibrated for the NoTouch to maintain optimal performance. Because the calibration values are stored in the NoTouch internal memory, each sensor must be calibrated with its paired NoTouch system.

  • Page 19: Notouch Troubleshooting

    IMPORTANT: REWINDER SENSORS ARE FACTORY CALIBRATED. THIS CALIBRATION IS STORED IN ONBOARD MEMORY ON THE NOTOUCH TOWER. DO NOT SWAP SENSORS IF YOU HAVE MULTIPLE NOTOUCH UNITS. If a sensor recalibration is needed, contact NeuraLabel support for assistance. • Slow down the printing.

  • Page 20: Unwinder Troubleshooting

    300x NoTouch User Guide Unwinder Troubleshooting The NoTouch Unwinder does not seem to be keeping up or performance is not satisfactory. • Check the Media Roll. Some media rolls are “sticky” so that the media sticks to itself as it unrolls. Watch for this problem.

Table of Contents