Table of Contents
Advertisement
Rolling Garage Door Opener
Installation Instructions And User Guide
RGD350/RGD400/RGD450
WARNING
Please read the manual carefully before installation and use. The installation of your new
door opener must be carried out by a technically qualified or licensed person. Attempting
to install or repair the door opener without suitable technical qualification may result in
severe personal injury, death and / or property damage.
Advertisement
Table of Contents
Related Manuals for SAMT RGD350
Summary of Contents for SAMT RGD350
- Page 1 Rolling Garage Door Opener Installation Instructions And User Guide RGD350/RGD400/RGD450 WARNING Please read the manual carefully before installation and use. The installation of your new door opener must be carried out by a technically qualified or licensed person. Attempting to install or repair the door opener without suitable technical qualification may result in...
-
Page 2: Safety Instructions
START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS WARNING • Failure to comply with the following instructions may result in serious personal injury or property damage. • Read and follow all instructions carefully. • The garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the instructions in this manual. - Page 3 suitable protective clothing where appropriate. 3.Frequently examine the door installation, in particular cable, springs and mountings for signs of wear, damage or imbalance. Do not use if repair or adjustment is needed since springs and hardware are under extreme tension and a fault can cause serious personal injury.
- Page 4 7.This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capablities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. 8.Automatic Drive - Keep away from the area of the door as it may operate unexpectedly.
- Page 5 13.Install the wireless wall control (or any additional wall control) in a location where the garage door is visible, at a height of at least 1.5 m and out of the reach of children. Do not allow children to operate push button(s) or transmitter(s).
-
Page 6: Table Of Contents
in order to avoid hazard. 18.Disconnect electric power and battery to the garage door opener before making repairs or removing covers. KEEP THESE INSTRUCTIONS CONTENTS PAGE CONTENTS PAGE SAFETY INSTRUCTIONS· · · · · · · · · · · · · · · · · · · · · · · · · IR Beam setting·... -
Page 7: Packing List
1.Packing List Standard list ： Selection list： 1.Weight bar X 1; 1.Rolling garage door opener X 1； 2.Remote control X 2； 2.Wall switch X 1; 3.Instructions X 1； 3. Extension pole bag X 1; 4.Clutch pull rope X 1； 5. Warning Label X 1； 2.TOOLS REQUIRED Socket wrench Adjustable... -
Page 8: Testing The Door
4.TESTING THE DOOR Complete the following test to ensure your door is well balanced, and not sticking or binding: • Disable all locks and remove any ropes connected to the garage door. • Lift the door to about halfway and then release it. The door should remain spring balanced. -
Page 9: The Release Handle & Cord
7.THE RELEASE HANDLE & CORD • Thread one end of the rope through the hole in the top of the red release handle so that “NOTICE” reads right side up as shown. • Secure with an overhand knot at least 25 mm from the end of the rope to prevent slipping. -
Page 10: Pinning The Door
9.PINNING THE DOOR Note: A ballooning door may delay the safety reversal response and can compromise garage door security. • To remedy any ballooning place self tapping metal screws or rivets where the curtain leaves the roll. Secure these through the curtain into the drum wheel at each end of the roll. -
Page 11: Installation Procedure
12.INSTALLATION PROCEDURE Do not allow people to walk under or around the door during the installation process as serious injury can occur. NOTE: The opener can be installed on either side of the door. The following instructions are for RIGHT HAND INSTALLATIONS (as illustrated i.e. inside the garage looking out). For left hand installations, reverse the instruction terminology (eg LEFT for RIGHT etc). -
Page 12: Basic Function Setting And Applying
Connect the power: • Position the power cable away from the door curtain and any moving parts. • Plug the opener into a nearby power point and turn ON. • The opener courtesy LEDs should turn ON. • The opener must now be programmed for : 1. -
Page 13: Ir Beam Setting
13.4 IR Beam setting Press and hold on “SET” button for 3 seconds until the LED flashes “1”. Press “UP” or “DOWN” button until the LED flashes “3”, press “SET” button. It’s now under IR Beam setting mode. The LED displays the current setting. -
Page 14: Installation Direction Setting
13.7 Lock door setting(Optional function) (Only when the lock door function is available, the setting can be proceed. The “lock” key can not be matched) Press and hold on “SET” button for 3 seconds until the LED flashes “1”. Press “UP” or “DOWN” button to increase or decrease. Adjust the LED to flash “6”, press “SET”... -
Page 15: Testing The Safety Reverse System
TESTING THE SAFETY REVERSE SYSTEM The safety reverse system test is important. The garage door must reverse on contact with a 40 mm obstacle laid flat on the floor. Failure to properly adjust the opener may result in serious personal injury from a closing garage door. -
Page 16: Install The Ir Beams (Optional Accessory)
16.INSTALL THE IR BEAMS (OPTIONAL ACCESSORY) NOTE: This accessory must be used for all installations where the closing force as measured on the bottom of the door is over 400 N (40 kgf). ENABLING THE PROTECTOR SYSTEM:(Section 13.4) * Door may operate unexpectedly, therefore do not allow anything to stay in the path of the door. -
Page 17: Install The Flash Light(Optional Accessory)
18.INSTALL THE FLASH LIGHT(OPTIONAL ACCESSORY) Can only use 24V DC Flash Light. 19.MAINTENANCE No particular maintenance is required for the logic circuit board. Check the door at least twice a year if it is properly balanced, and all working parts are in good working condition or not. -
Page 18: Important Information For The User
In the case of a malfunction the user must call an authorized installer and IMPORTANT NO TE: should not attempt to repair it by yourself. 22.SPECIFICATIONS SILENTDRIVE Model RGD350 RGD400 RGD450 Opening Speed 200MM/S 200MM/S... -
Page 19: Common Fault & Solutions
COMMON FAULT & SOLUTIONS Fault appearance Fault cause Solutions Opener without any 1. Power supply 1. Check the power supply to openers. action 2. Plug wire are loosing 2. Carefully open the motor cover, check all plug wire on control boards. Opener doesn’t work, Faulty learning of “UP”...
Need help?
Do you have a question about the RGD350 and is the answer not in the manual?
Questions and answers