Table of Contents
Advertisement
VCC Parameters Menu
The parameters menu provides access to network settings
as well as various test functions. Below is a flow chart of
the Parameters menu.
Network terminal settings
This menu selection provides access to the IP parameters
used for communicating with the print server. See below
for a flow chart and description of the Network settings
menu.
NETWORK SETTINGS
COPIER TIMING
COPIER STANDARD
COPIER STEERING
TEST CARD READER
PING UTILITY
MISC PARAMS
Copier timing
This control provides a way to adjust the sense time, blind
time, reset delay and eject delay used during the copier
test modes, Copier standard and Copier steering. These
settings apply only during off-line testing. Timer values
used when the VCC is online are downloaded from the
print vend software and must be set there. The timing
adjustments made here apply to both sets of opto inputs
and relays; there are no provisions for separate control of
inputs one and two in off-line test mode. Timing resolution
is 10ms. Press Enter or C/CE to exit and save the changes
+ to increase timing
- to decrease timing
to move to previous timer
to move to next timer
Copier standard
This menu selection provides a way to test the VCC in
standard mode using the timing parameters set under
Copier timing. The VCC display provides a visual of the
state each of the optos are in. Relays are turned on and
off by pressing '1' for relay one and pressing '2' for relay
two. Meters roll over at 10. In standard mode, debit pulses
should only come in on optos 1 and 2 and only Mtr 1 and
Mtr 2 should change. Press C/CE to exit this selection
Opto 1
Opto 2
state
state
Mtr
Mtr
Mtr
Mtr
1
2
3
4
Copier steering
This menu selection provides a way to test the VCC in
steering mode using the timing parameters set under
Copier timing. The VCC display provides a visual of the
state each of the optos are in. Relays are turned on and
off by pressing '1' for relay one and pressing '2' for relay
two. Meters roll over at 10. In steering mode, debit pulses
should come in only on opto 1. Optos 2-4 provide the
steering signal as the copier selections change. In this
mode Mtrs 1-8 may change. Press C/CE to exit this
selection.
Opto 1
Opto 2
state
state
Mtr
Mtr
Mtr
Mtr
1
2
3
4
Test card reader
This menu selection provides a way to test the card reader
whether it's a mag swipe, bar code or contactless card.
Everything read off the card is displayed unfiltered. What
is viewed here is what gets sent to the server when on-
line. The display can show up to 40 characters. Press
C/CE to exit this selection.
Ping utility
This menu selection provides a way to send periodic PING
echo request packets. When entering this menu for the
first time after a boot up, the IP displayed is the server IP
whether it's issued through Fixed IP or a DNS operation.
The ping utility will send an ICMP packet with 32 bytes of
data at 2 second increments for as long as this menu is
open. The display shows the bytes sent, bytes received
and duplicated received ping echo reply packets. The
display counter will roll over at 255. Note; the ping
address can be edited, simply type in the address you wish
to use. Press C/CE to exit this selection.
Hostname
This is the name given the VCC for the purpose of
identifying it on a DHCP/DNS enabled network. This name
is not programmable but fixed at "VCCxxxx" where xxxx is
the last four digits of the MAC address. The hostname is
passed to the DHCP server in the DHCP request packet.
The DHCP server must be configured to pass this to the
DNS server. This menu selection is only visible in DHCP
mode.
Virtual Cash Controller product guide – page 6
Opto 3
Opto 4
State
state
Mtr
Mtr
Mtr
Mtr
5
6
7
8
Opto 3
Opto 4
state
State
Mtr
Mtr
Mtr
Mtr
5
6
7
8
Relay
(1,2,B)
Relay
(1,2,B)
Advertisement
Table of Contents
