Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Rev. 0913
After delivery, immediately remove the packaging from the product in a manner that preserves the packaging
and maintains the orientation of the product in the packaging; then inspect the product closely to determine whether it
sustained damage during transport. If damage is discovered during the inspection, immediately record a
complete description of the damage on the bill of lading. If the product is undamaged, discard the packaging.
NOTES:
1) Compliance with laws, regulations, codes, and non-voluntary standards enforced in the location where the
product is used is exclusively the responsibility of the owner/end-user.
2) The manufacturer is not liable for any injury or property damage that occurs as a consequence of failing to apply
a) the instructions manual; or b) information provided on labels affixed to the product. Neither is the
responsible manufacturer for any consequential damages sustained as a result of failing to exercise
sound judgment while assembling, installing, using or maintaining this product.
Table of Contents
Hazard Identification: explanation of signal words............................................................................... 2
Safety Guidelines......................................................................................................................... 2
Product Introduction..................................................................................................................... 3
Bills of materials for CART-550-SS and 1100-SS................................................................................ 5, 7
Assembly Instructions................................................................................................................... 8
Use Instructions........................................................................................................................... 9-11
Loading...................................................................................................................................... 9
Lift Table Operation..................................................................................................................... 10
Hydraulic System Operation.......................................................................................................... 10-11
Inspections & Maintenance............................................................................................................ 12
Troubleshooting........................................................................................................................... 13
FIG. 1: CART-550-SS Exploded Parts Diagram................................................................................. 4
FIG. 2: CART-1100-SS Exploded Parts Diagram................................................................................ 6
FIG. 3: Hydraulics Diagram............................................................................................................ 8
FIG. 4: Spline and Pin Connection................................................................................................... 8
FIG. 5: Handle Insertion................................................................................................................ 8
FIG. 6: Pedal Attachment.............................................................................................................. 8
FIG. 7A & 7B: Proper Load Positioning (Top View & Side View)............................................................ 9
FIG. 8: Caster Brake Lever............................................................................................................ 10
FIG. 9: Hydraulic Control Pedal Positions.......................................................................................... 11
FIG. 10: Maintenance Prop Installation............................................................................................. 12
FIG. 11: Label Placement.............................................................................................................. 14
CART-550-SS & CART-1100-SS
Instruction Manual
CART-1100-SS, manual.doc
Page 1 of 15
Page
Advertisement
Table of Contents
Related Manuals for Vestil CART-550-SS
Summary of Contents for Vestil CART-550-SS
-
Page 1: Table Of Contents
Table of Contents Page Hazard Identification: explanation of signal words……………………………………………………………………. 2 Safety Guidelines….……………………………………………………………………………………………………… 2 Product Introduction……………………………………………………………………………………………………… 3 Bills of materials for CART-550-SS and 1100-SS…………………………………………………………………….. 5, 7 Assembly Instructions……………………………………………………………………………………………………. 8 Use Instructions…………………………………………………………………………………………………………... 9-11 Loading…………………………………………………………………………………………………………………..9 Lift Table Operation……………………………………………………………………………………………………… 10 Hydraulic System Operation……………………………………………………………………………………………. 10-11 Inspections &... -
Page 2: Hazard Identification: Explanation Of Signal Words
HAZARD IDENTIFICATION: explanation of signal words This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries, as well as the probable seriousness of those injuries, if the product is misused in the ways described. Other signal words call attention to uses of the product likely cause property damage. -
Page 3: Product Introduction
Specifications for the two stainless steel cart models appear in the table below: Platform Size Vertical Range Net Wt. (lbs.) (W x L) in inches of Motion (in.) Capacity (lbs.) CART-550-SS 19 -½“ x 31-½” 9-¾“ to 33-½“ CART-1100-SS 23-½ “ x 35-½“ 13” to 38½ “ 1,100 This manual was created to acquaint owners and users of our stainless steel carts with safe use and maintenance procedures. -
Page 4: Table Of Figures Fig. 1: Cart-550-Ss Exploded Parts Diagram
FIG. 1: CART-550-SS Exploded Parts Diagram Relief Valve Assembly Page 4 of 15... -
Page 5: Bills Of Materials For Cart-550-Ss And 1100-Ss
CART-550-SS bill of materials Item No. Part No. Description Item No. Part No. Description C-500-SS-101 Table Deck C-500-SS-227 Washer C-500-SS-102 Arm Pin C-500-SS-228 C-500-SS-103 Washer Inlet & Outlet Check Valves C-500-SS-104 Bolt C-500-SS-229 Steel Ball C-500-SS-105 Cylinder Pin C-500-SS-230 Spring... -
Page 6: Fig. 2: Cart-1100-Ss Exploded Parts Diagram
FIG. 2: CART-1100-SS Exploded Parts Diagram Relief Valve Assembly Page 6 of 15... - Page 7 CART-1100-SS bill of materials Item No. Part No. Description Item No. Part No. Description C-1100-SS-101 Deck (of table) C-1100-SS-227 Bushing C-1100-SS-102 Bolt C-1100-SS-228 Grease Nipple C-1100-SS-103 Stainless Washer C-1100-SS-229 Pedal Link C-1100-SS-104 Arm Pin C-1100-SS-230 Plunger Piston C-1100-SS-105 Cylinder Pin C-1100-SS-231 Spring Cap C-1100-SS-106...
-
Page 8: Assembly Instructions
FIG. 3: Hydraulics Diagram reduce possibility of injury, BEFORE working on the hydraulic system: CYLINDER 1. Fully lower and secure the deck; 2. Release system pressure disconnect all power sources; 3. DO NOT work on the hydraulic VELOCITY FUSE components UNLESS you are trained and authorized to do so. -
Page 9: Use Instructions
Use Instructions: The cart is suitable for use in most industrial and commercial settings. Only authorized persons should use the scissors lift cart. “Authorized person” means someone the end-user approves or assigns to use the cart because he/she is either: 1. -
Page 10: Lift Table Operation
Lift Table Operation Take reasonable precautions to avoid the obvious potential hazards of using a cart: 1. Instruct other persons in the area to stand at a safe distance while raising or lowering the deck. Be certain no part of any person, clothing, or object is under any part of the cart before lowering the deck. 2. -
Page 11: Fig. 9: Hydraulic Control Pedal Positions
FIG. 9: Hydraulic Control Pedal Positions 2: L OSITION 1: H OSITION IGH SPEED FOR PEED FOR IFTING ONLY (U AISING NLOADED To lower the deck, open the release valve by turning the release knob counterclockwise. The release knob is item #250 in FIG. -
Page 12: Inspections & Maintenance
Inspections & Maintenance: Only trained and authorized persons should maintain, repair, adjust and inspect the scissor lift cart. Maintenance and inspection personnel should verify that the cart complies with all regulations, codes, and standards that apply to Industrial Scissors Lifts in the location where the cart is used. The person(s) designated to conduct inspections by your employer must inspect the cart BEFORE it is used for the first time and prior to EACH use thereafter. -
Page 13: Troubleshooting
Troubleshooting: Problem Possible Causes Action Deck does not elevate a. Load weight exceeds lifting a. Remove load and use capacity another cart with greater lifting capacity b. relief valve set too low b. remove part of the load c. load cart with rated load, increase the relief-valve setting until the rated load will rise. -
Page 14: Fig. 11: Label Placement
Label placement diagram: Only use the lifter if ALL labels are readable and undamaged. Contact us for replacement labels if necessary, and DO NOT use the lifter until all replacement labels are affixed to the device. Outside surfaces Label #206: Oil specifications. Label #212: Label #208: The scissor legs create pinch points as the deck rises and lowers. - Page 15 LIMITED WARRANTY This product is warranted to be free of defects in material and workmanship during the warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part is covered by the warranty, after we receive a proper request from the warrantee (you) for warranty service.