Download Print this page
Pearl Iron Jet IRONJ 05 Installation And Operating Instructions

Pearl Iron Jet IRONJ 05 Installation And Operating Instructions

Shallow well jet pumps

Advertisement

Quick Links

TO AVOID SERIOUS OR FATAL PERSONAL INJURY OR MAJOR
PROPERTY DAMAGE, READ AND FOLLOW ALL SAFETY
INSTRUCTIONS IN MANUAL AND ON PUMP.
This is a SAFETY ALERT SYMBOL. When
you see this symbol on the pump or in the
manual, look for one of the following signal
words and be alert to the potential for
personal injury or property damage.
Warns of hazards that WILL cause serious
!
personal injury, death or major property
damage.
DANGER
Warns of hazards that CAN cause serious
!
personal injury, death or major property
damage.
WARNING
Warns of hazards that CAN cause personal
!
injury or property damage.
CAUTION
NOTICE: PLEASE READ AND UNDERSTAND THIS MANUAL
BEFORE OPERATE OR INSTALL THE PRODUCT. IF YOU HAVE
ANY QUESTION, PLEASE CONTACT YOUR DISTRIBUTOR FOR
INSTRUCTION.
THIS MANUAL MUST BE KEPT WITH THE PUMP.
MAINTAIN ALL SAFETY LABELS.
IMPORTANT PRE-INSTALLATION INFORMATION
Hazardous voltage can shock, burn or cause
death. All electrical work must be performed
by a qualified technician. Always follow the
local applicable electrical code.
The pump must be connected to a dedicated
electrical circuit protected by a properly sized
circuit breaker or fuses. Install a disconnect
Control Panel where required by the local
code.
Code questions should be directed to your electrical inspector.
See Chart 1 for specific information.
Always disconnect the power source before
installing or servicing the pump. This motors
come with an automatic thermal overload
protection, this feature may allow an
overheated pump to restart suddenly.

INSTALLATION AND OPERATING INSTRUCTIONS

Water and electricity can be dangerous if
certain precautions are not adhered to. This
!
pump is designed to operate in a safe way in
a water environment; however, improper use
DANGER
and installation can result in personal harm
from electrical shock. Please pay attention to
the following warnings.
Never touch this pump, when it is touching
water, in water, or even in a moist
!
environment. Always unplug (disconnect the
electricity) when working on or installing
DANGER
the unit.
Do not use this pump with flammable or
explosive liquids such as oil, gasoline,
kerosene, ethanol, etc. Using this pump
with or near flammable liquids can cause an
explosion or fire, resulting in property damage,
serious personal injury and/or death. Pumping
any of the above mentioned liquids voids the
warranty. Always make sure that this pump
is pumping liquid with same composition as
water.
Do not stand in water when the pump is
connected to the power supply.
!
This pump has been evaluated for use with
water only.
CAUTION
NOTICE: This pumps has been designed for working in presence
of water. Working without water will cause severe damage to
the pump.
IRONJET
shallow well jet pumps

Advertisement

loading

Summary of Contents for Pearl Iron Jet IRONJ 05

  • Page 1: Installation And Operating Instructions

    IRONJET shallow well jet pumps INSTALLATION AND OPERATING INSTRUCTIONS TO AVOID SERIOUS OR FATAL PERSONAL INJURY OR MAJOR PROPERTY DAMAGE, READ AND FOLLOW ALL SAFETY INSTRUCTIONS IN MANUAL AND ON PUMP. This is a SAFETY ALERT SYMBOL. When you see this symbol on the pump or in the manual, look for one of the following signal words and be alert to the potential for personal injury or property damage.
  • Page 2 temporarily wasting the water outdoors or to drain. The pump A qualified electrician must perform all the should be operated until the water runs clear, without sand, mud wiring. or rust. CAUTION This procedure will eliminate the danger of pumping dirty water into the pressure tank and home appliances.
  • Page 3 6. Connect pump discharge to pressure tank, and pressure tank to house plumbing. Te e 7. After piping is completed and motor is properly wired, remove the priming plug on top of pump and fill pump with clean water. Allow time for air in the system to escape, and refill pump if necessary before replacing the priming plug.
  • Page 4 Remove the Choose connection Reinstall the cover Voltage plug. for 230 V. back. 9. PEARL MOTOR DATA 10. PEARL MOTOS ARE PRE-WIRED BY HP: - 1/2 wired for 115 Volt. MOTOR SERVICE Pump MAX. VOLTS PHASE - 3/4 - 1 1/2 HP wired for 230 Volt.

This manual is also suitable for:

Iron jet ironjh 05Iron jet ironj 10Iron jet ironj 07Iron jet ironj 15