Sony CDP-CE575 Operating Instructions (primary manual) Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. CD Player
  5. CDP-CE575 - Disc Carousel
  6. Service manual
Sony CDP-CE575 Operating Instructions (primary manual) Service Manual

Sony CDP-CE575 Operating Instructions (primary manual) Service Manual

Cd/sacd players & changers: disc carousel
Hide thumbs Also See for CDP-CE575 Operating Instructions (primary manual):
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
Ver 1.1 2001.07
Compact disc player
Laser
Frequency response
Dynamic range
Harmonic distortion
Outputs
Jack
type
ANALOG
Phono
OUT
jacks
DIGITAL
Optical
OUT
output
(OPTICAL)
connector
PHONES
Stereo
phone
jack
Sony Corporation
9-929-586-12
2001G0500-1
Home Audio Company
C 2001.7
Shinagawa Tec Service Manual Production Group
CDP-CE575
SPECIFICATIONS
Semiconductor laser ( =
780 nm)
Emission duration:
continuous
2 Hz to 20 kHz 0.5 dB
More than 93 dB
Less than 0.0045%
Maximum
Load
output level
impedance
2 V
Over 10
(at 50 kilohms)
kilohms
–18 dBm
Wave
length:
660 nm
10 mW
32 ohms
Canadian Model
Model Name Using Similar Mechanism
CD Mechanism Type
Base Unit Name
Optical Pick-up Name
General
Power requirements
120 V AC, 60 Hz
Power consumption
11 W
Dimensions (approx.)
430 x 110 x 400 mm
(w/h/d)
(17 x 4 3/8 x 15 3/4 in.)
incl. projecting parts
Mass (approx.)
5.2 kg (11 lbs 8 oz)
Supplied accessories
Audio cord (2 phono plugs – 2 phono plugs) (1)
Remote commander (remote) (1)
R6 (size AA) batteries (2)
Design and specifications are subject to change
without notice.
COMPACT DISC PLAYER
US Model
AEP Model
NEW
CDM59-5BD27
BU-5BD27
PXR-104X

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CDP-CE575 Operating Instructions (primary manual) and is the answer not in the manual?

Questions and answers

Related Manuals for Sony CDP-CE575 Operating Instructions (primary manual)

Summary of Contents for Sony CDP-CE575 Operating Instructions (primary manual)

  • Page 1 Optical –18 dBm output (OPTICAL) connector PHONES Stereo 10 mW phone jack Sony Corporation 9-929-586-12 2001G0500-1 Home Audio Company C 2001.7 Shinagawa Tec Service Manual Production Group CDP-CE575 Model Name Using Similar Mechanism CD Mechanism Type Base Unit Name Optical Pick-up Name...

  • Page 2: Table Of Contents

    SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

  • Page 3: Serviceing Notes

    NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body.
  • Page 4 CDP-CE575 SHIPMENT MODE Performed when returning the unit to the customer. Custom File Erases all custom files and initializes settings. Procedure: 1. Remove the discs from all trays. 2. While pressing the DISK SKIP button and PROGRAM but- ton, press the POWER button to turn ON the power. 3.
  • Page 5 Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is no a fault.) TRACK Recorded contents ! ” # $ % & ´ (21h to 27h)1kHz 0dB L&R + , – . / (28h to 2Fh) 0 1 2 3 4 5 6 7 (30h to 37h)

  • Page 6: General

    CDP-CE575 Parts Identification Front Panel The items are arranged in alphabetical order. Refer to the pages indicated in parentheses ( ) for details. CHECK qh (13) CLEAR qj (13, 14, 16, 17) CONTINUE 2 (9, 13, 15, 18) DISC 1–5 3 (9, 10, 13) Disc compartment ws (9) DISC SKIP 9 (9, 12, 13) Display 4 (11)

  • Page 7: Remote Control

    Remote Control ANALOG OUT LEVEL +/– wh (6, HIGH-LIGHT wd (12) 7, 10) MEGA CONTROL 4 (18, 19) CD1/2/3 switch 1 (7) MUSIC SCAN qa (10) CHECK 9 (13) NAME INPUT qs (17) CLEAR ws (13, 14, 16, 17) NO DELAY ql (19, 20) CONTINUE 3 (9, 13, 15, 18) Number buttons 7 (10, 13, 17) DISC/CAPS 6 (10, 17)

  • Page 8: Disassembly

    CDP-CE575 • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2. CASE (409538) (Page 9) 3-3. FRONT PANEL SECTION (Page 9) 3-4. CD MECHANISM DECK (CDM59-5BD27) (Page 10) 3-6. BASE UNIT (BU-5BD27) (Page 11) 3-7. TABLE ASSY (Page 11) 3-8.

  • Page 9: Case (409538)

    3-2. CASE (409538) 1 two screws (case3 TP2) 3-3. FRONT PANEL SECTION 2 connector 4 claw (CN601) 2 connector (CN602) 3 four screws (BVTP3 3 case (409538) 2 two screws (BVTP3 1 two screws 1 wire (flat type) (15 core) 2 connectors (CN351) 4 claw...

  • Page 10: Cd Mechanism Deck (Cdm59-5Bd27)

    CDP-CE575 3-4. CD MECHANISM DECK (CDM59-5BD27) 3 three screws 5 screw (BVTP3 4 Slide the tray until the screw that fixes the table assy can be seen through around hole in the table assy. 3-5. MAIN BOARD 5 MAIN board (BVTP3 1 Insert a tapering driver from the bottom of the chassis, and turn it in the direction of the arrow until the base unit...

  • Page 11: Table Assy

    3-6. BASE UNIT (BU-5BD27) 4 two screws Note: When installing the BU on the chassis, set the gear (U/D) lever (lifter) in free position, the gear (U/D) in UP position, and insert the shaft into the groove of gear (U/D). 3-7.

  • Page 12: Sensor Board

    CDP-CE575 3-8. SENSOR BOARD 2 tray 3-9. LOADING MOTOR BOARD 4 LOADING MOTOR board 1 screw (PTPWH M2.6) 5 SENSOR board 4 two screws (BTTP M2.6) 3 two screws (BTTP M2.6) 1 belt (loading) 3 belt (rotary) 4 two screws (BTTP M2.6) 2 connector (CN13)

  • Page 13: Assembly

    Note: Follow the assembly procedure in the numerical order given. ADJUSTING PHASE OF SWING GEAR AND GEAR (U/D) 3 Let the swing gear through under the chassis and engage its dowel with the groove of rotary encoder. 2 Install the rotary encoder so that its groove comes to the position shown in the figure.

  • Page 14: Adj Mode

    CDP-CE575 ADJ MODE NOTE: This mode cannot be performed without a general remote com- mander. 1. Chuck the CD first, and then turn OFF the power. 2. Short-circuit the test point TP (ADJ) of the MAIN board and ground with a lead wire. [POWER] 3.
  • Page 15 Buttons and Corresponding Button Numbers Button Button Number or Display DISC1 DISC2 DISC3 DISC4 DISC5 CONTINUE SHUFFLE PROGRAM REPEAT TIME/TEXT EDIT CHECK CLEAR PEAK SEARCH FADER Partial lighting 1 (grid check) Partial lighting 1 (segment check) EX-CHANGE DISC SKIP MENU X-FADE, NO DELAY MEGA CONTROL l AMS L (push)

  • Page 16: Aging Mode

    CDP-CE575 AGING MODE For the aging mode, three modes of all mode, disc table mode, and loading mode are available. Code No. Status CLOSE (Tray close) TOC read Access to last track Play of last track (2 sec) EX OPEN (Tray open while chucking) EX SKIP (Disc tray rotate) EX CLOSE (Tray close) Access to first track...
  • Page 17 MECHANISM DECK CHECK MODE For the mechanism desk check mode, two modes of the disc table mode and the loading mode are available. In the mechanism deck check mode, the disc table rotating time and the loading time in each section are measured and displayed. Disc Table Mode Procedure: [POWER]...

  • Page 18: Electrical Adjustments

    CDP-CE575 Ver 1.1 2001.07 Note: 1. CD Block is basically designed to operate without adjustment. There- fore, check each item in order given. 2. Use PATD-012 disc (4-225-203-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10M impedance. 4.
  • Page 19 E-F Balance Check Connection: oscilloscope BD board TP (TE1) TP (VC) – Procedure: Set the test disc (PATD-012). Disc chucking operation is [POWER] complete, then press the off. Connect an oscilloscpe to test point TP (TE1) and TP (VC) on the BD board.
  • Page 20 CDP-CE575 MEMO...

  • Page 21: Diagrams

    SECTION 7 DIAGRAMS 7-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Schematic Diagram: Note on Printed Wiring Board: • All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side. 50 WV or less are not indicated except for electrolytics •...

  • Page 22: Printed Wiring Board - Bd Section

    CDP-CE575 Ver 1.1 2001.07 7-2. PRINTED WIRING BOARD – BD Section – • See page 21 for Circuit Boards Location. BD BOARD (COMPONENT SIDE) C150 C112 R110 R184 R174 R111 C182 C181 R112 C172 C193 C171 C194 C192 C191 C111 FB191 X191 C199...

  • Page 23: Schematic Diagram - Bd Section

    7-3. SCHEMATIC DIAGRAM – BD Section – • See page 32 for Waveforms. (Page 26) • See page 29 for IC Block Diagrams. TP (RFDC) CDP-CE575 Ver 1.1 2001.07 The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont line with mark 0 are critical for safety.

  • Page 24: Printed Wiring Boards - Motor/Sensor Section

    CDP-CE575 7-4. PRINTED WIRING BOARDS – MOTOR/SENSOR Section – • See page 21 for Circuit Boards Location. MAIN BOARD (Page 28) CN311 (TABLE SENSOR) (DISC SENSOR)

  • Page 25: Schematic Diagram - Motor/Sensor Section

    CDP-CE575 7-5. SCHEMATIC DIAGRAM – MOTOR/SENSOR Section – • See page 29 for IC Block Diagram. (Page 26)

  • Page 26: Schematic Diagram – Main Section (1/2)

    CDP-CE575 7-6. SCHEMATIC DIAGRAM – MAIN Section (1/2) – • See page 32 for Waveform. (Page 23) (Page 27) (Page 25) (Page 31)

  • Page 27: Schematic Diagram - Main Section (1/2)

    7-7. SCHEMATIC DIAGRAM – MAIN Section (2/2) – (Page 26) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. CDP-CE575 Les composants identifiés par une marque 0 sont critiques pour la sécurité.

  • Page 28: Printed Wiring Boards - Main Section

    CDP-CE575 7-8. PRINTED WIRING BOARDS – MAIN Section – • See page 21 for Circuit Boards Location. MAIN BOARD JW20 R520 R514 C505 JW18 JW19 R509 J301 R510 IC502 R511 R515 R513 C507 R512 ANALOG Q504 Q502 R420 Q352 R522 C407 R519 C508...
  • Page 29 • IC Block Diagrams – BD Board – IC101 CXD2587Q ERROR DIGITAL CORRECTOR DIGITAL ASYMMETRY CORRECTION LRCK PCMD INTERFACE DEMODULATOR EMPH XVDD XTAI TIMING LOGIC XTAO XVSS AVDD1 AOUT1 AIN1 LOUT1 SUBCODE AVSS1 PROCESSOR AVSS2 LOUT2 3rd ORDER NOISE SHAPER SERVO INTERFACE OVER SAMPLING...

  • Page 30: Printed Wiring Boards - Display Section

    CDP-CE575 7-9. PRINTED WIRING BOARDS – DISPLAY Section – • See page 21 for Circuit Boards Location. DISPLAY BOARD . AMS > CNP801 (DISC) PUSH ENTER R814 R813 R815 DISC S815 S814 EX-CHANGE SKIP R807 MAIN BOARD R816 D801 CN801 (Page 28) R822 S801...

  • Page 31: Schematic Diagram - Display Section

    CDP-CE575 7-10. SCHEMATIC DIAGRAM – DISPLAY Section – • See page 32 for Waveform. (Page 26)

  • Page 32: Ic Pin Function Description

    CDP-CE575 • Waveforms – BD Board – 1 IC101 ta (RFAC) (CD Play Mode) 6 IC101 w; (SCOR) (CD Play Mode) 1.3 Vp-p 13.4 ms 2 IC101 rd (RFDC) (CD Play Mode) 7 IC101 yj (XTAO) (CD Play Mode) 1.4 Vp-p 59 ns 3 IC101 el (FE) (CD Play Mode) approx.
  • Page 33 Pin No. Pin Name RFDC RF signal input from the CXA2581N (IC131) ADIO Monitor output of the A/D converter input signal Not used (open) AVSS0 — Ground terminal (digital system) IGEN Stabilized current input for operational amplifiers AVDD0 — Power supply terminal (+5V) (digital system) ASYO Playback EFM full-swing output terminal ASYI...
  • Page 34 CDP-CE575 MAIN BOARD IC301 CXP84648-085Q (SYSTEM CONTROLLER) Pin No. Pin Name 1 to 4 A3 to A6 Address signal output to the static RAM (IC302) — Ground terminal 6 to 13 D0 to D7 Two-way data bus with the static RAM (IC302) Chip select signal output to the static RAM (IC302) 15 to 18 —...
  • Page 35 Pin No. Pin Name Not used (fixed at “H”) Serial data latch pulse signal output to the CXD2587Q (IC101) 59, 60 — Not used (open) SCOR Sub-code sync (S0+S1) detection signal input from the CXD2587Q (IC101) BUSIN Sircs remote control signal input from the CONTROL A1II BUSOUT Sircs remote control signal output to the CONTROL A1II SMUTE...

  • Page 36: Exploded Views

    CDP-CE575 NOTE: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) Parts Color Cabinet's Color 8-1. CASE SECTION not supplied Ref.

  • Page 37: Front Panel Section

    8-2. FRONT PANEL SECTION Ref. No. Part No. Description 4-231-928-01 KNOB (AMS) 3-354-981-11 SPRING (SUS), RING 1-681-134-11 KEY (A) BOARD (US, CND) 1-681-134-21 KEY (A) BOARD (AEP) 4-231-973-01 BUTTON (POWER) 1-681-135-11 POWER SW BOARD (US, CND) 1-681-135-21 POWER SW BOARD (AEP) 4-951-620-01 SCREW (2.6X8), +BVTP 1-681-137-11 KEY (B) BOARD (US, CND) Remark...

  • Page 38: Chassis Section

    CDP-CE575 8-3. CHASSIS SECTION not supplied not supplied not supplied Ref. No. Part No. Description 4-232-237-01 FOOT (DIA. 30) X-4953-448-1 FOOT ASSY 4-943-687-01 HOLDER, BOARD A-4725-582-A MAIN BOARD, COMPLETE (US, CND) A-4725-593-A MAIN BOARD, COMPLETE (AEP) 1-757-648-11 WIRE (FLAT TYPE) (21 CORE) 3-703-249-01 SCREW, S TIGHT, +PTTWH 3X6 3-703-244-21 BUSHING (2104), CORD CDM59-5BD27...

  • Page 39: Cd Mechanism Deck Section-1 (Cdm59-5Bd27)

    8-4. CD MECHANISM DECK SECTION-1 (CDM59-5BD27) not supplied Ref. No. Part No. Description 1-676-245-11 SENSOR BOARD 4-218-253-31 SCREW (M2.6), +BTTP * 503 X-4924-457-1 ROLLER ASSY 4-224-602-01 TABLE 4-224-617-01 GEAR (RM-E) 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING 4-224-616-01 GEAR (RM-M) not supplied CD MECHANISM DECK SECTION-2 Remark Ref.

  • Page 40: Cd Mechanism Deck Section-2 (Cdm59-5Bd27)

    CDP-CE575 8-5. CD MECHANISM DECK SECTION-2 (CDM59-5BD27) S200 not supplied Ref. No. Part No. Description 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING X-4952-312-1 HOLDER (BU) ASSY 4-959-996-01 SPRING (932), COMPRESSION 4-225-885-01 BELT (LOADING) 4-225-844-01 GEAR (LOADING A) 4-224-613-01 GEAR (SHAFT) 1-676-244-11 LOADING MOTOR BOARD 4-218-253-31 SCREW (M2.6), +BTTP 4-224-607-01 GEAR, SWING 4-224-609-01 GEAR (LOADING C)

  • Page 41: Base Unit Section (Bu-5Bd27)

    8-6. BASE UNIT SECTION (BU-5BD27) M101 Ref. No. Part No. Description 4-951-620-01 SCREW (2.6X8), +BVTP A-4725-568-A BD BOARD, COMPLETE 4-951-940-01 INSULATOR (BU) 4-917-565-01 SHAFT, SLED 0 605 1-796-033-11 OPTICAL PICK-UP (PXR-104X) 1-782-817-11 WIRE (FLAT TYPE) (16 CORE) M102 The components identified by mark 0 or dotted line with mark 0 are critical for safety.

  • Page 42: Electrical Parts List

    CDP-CE575 NOTE: • Due to standardization, replacements in the parts list may be different from the parts speci- fied in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one.
  • Page 43 Ref. No. Part No. Description R142 1-216-841-11 METAL CHIP R143 1-216-855-11 METAL CHIP R144 1-216-846-11 METAL CHIP R145 1-216-830-11 METAL CHIP R146 1-216-845-11 METAL CHIP R149 1-216-821-11 METAL CHIP R151 1-216-845-11 METAL CHIP R152 1-216-833-11 METAL CHIP R153 1-216-864-11 SHORT R155 1-216-836-11 METAL CHIP R171...
  • Page 44 CDP-CE575 DISPLAY HEADPHONE LOADING MOTOR MAIN Ref. No. Part No. Description S846 1-771-349-21 SWITCH, KEYBOARD (A OPEN/COLSE) ************************************************************** 1-681-136-11 HEADPHONE BOARD (US, CND) 1-681-136-21 HEADPHONE BOARD (AEP) ***************** < CAPACITOR > C881 1-162-294-31 CERAMIC 0.001uF C882 1-162-294-31 CERAMIC 0.001uF C883 1-164-159-11 CERAMIC 0.1uF <...
  • Page 45 Ref. No. Part No. Description C381 1-164-159-11 CERAMIC C382 1-164-159-11 CERAMIC C404 1-126-965-11 ELECT C405 1-104-664-11 ELECT C406 1-126-933-11 ELECT C407 1-162-290-31 CERAMIC C408 1-107-715-11 ELECT C451 1-126-933-11 ELECT C504 1-126-965-11 ELECT C505 1-104-664-11 ELECT C506 1-126-933-11 ELECT C507 1-162-290-31 CERAMIC C508 1-107-715-11 ELECT C551...
  • Page 46 CDP-CE575 MAIN POWER SW Ref. No. Part No. Description R329 1-249-425-11 CARBON 4.7K R350 1-247-807-31 CARBON R351 1-247-807-31 CARBON R352 1-249-441-11 CARBON 100K R353 1-249-441-11 CARBON 100K R354 1-249-441-11 CARBON 100K R355 1-249-441-11 CARBON 100K R356 1-249-441-11 CARBON 100K R381 1-249-425-11 CARBON 4.7K R382...

  • Page 47: Accessories And Packing Materials

    Ref. No. Part No. Description S200 1-418-746-11 ENCODER, ROTARY (BU, TABLE ADDRESS DETECT) 0 T601 1-435-342-11 TRANSFORMER, POWER (US, CND) 0 T601 1-435-343-11 TRANSFORMER, POWER (AEP) ************************************************************ ACCESSORIES & PACKING MATERIALS ******************************* 1-418-858-11 REMOTE COMMANDER (RM-DC545) 1-558-271-11 CORD, CONNECTION (RCA PIN PLUG) 1-777-241-11 CORD, CONNECTION (MINI PLUG) (CND) 4-233-301-11 MANUAL, INSTRUCTION (ENGLISH) (US) 4-233-301-21 MANUAL, INSTRUCTION (ENGLISH, FRENCH)

  • Page 48: Revision History

    CDP-CE575 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date 2001.07 2001.03 Description of Revision Addition of electrical adjustments...

Table of Contents