Related Manuals for Wilo Control SC-Fire Electric
Summary of Contents for Wilo Control SC-Fire Electric
- Page 1 Pioneering for You Wilo-Control SC-Fire Electric de Einbau- und Betriebsanleitung Inbouw- en bedieningsvoorschriften en Installation and operating instructions Notice de montage et de mise en service 2 541 365-Ed.01 / 2014-02-Wilo...
- Page 2 Fig. 1: SPRINKLER PUMP MOTOR SUPPLY. I ON NOT TO BE SWICHED OFF IN THE EVENT OF FIRE...
- Page 4 Fig. 2:...
- Page 6 Measurement board: converting current and voltage values Button: Lamp test Note regarding the main switch: Button: Acknowledgement of error messages Power supply for the sprinkler pump motor. DO NOT SWITCH OFF IN THE EVENT OF A FIRE! WILO SE 01/2014...
- Page 7 Children should be supervised to ensure that they do not play with the appliance. Installation and operating instructions Wilo SC-Fire Electric...
-
Page 8: Application (Intended Use)
The operating safety of the supplied product is only guaranteed for conventional use in accord- ance with Section 4 of the operating instructions. The limit values must on no account fall under or exceed those specified in the catalogue/data sheet. WILO SE 01/2014... -
Page 9: Product Information
The system is operated using the rotary knob and the buttons in the door. Potential-free contacts are available for forward- ing run or fault signals messages to the building management system. Installation and operating instructions Wilo SC-Fire Electric... - Page 10 (falling edge in case of a after a configurable delay (see menu 1.2.5.3) and fault = “fall”) or positive logic (rising edge in case the collective fault signal (Fig. 2, item 6) lights up of a fault = “raise”). WILO SE 01/2014...
- Page 11 Go back (brief press: one menu level; long press: main screen) EASY menu EXPERT menu Meaning: Service not logged in Meaning: Display value – no entry possible Service menu Parameter Information Fault Reset fault Alarm settings Installation and operating instructions Wilo SC-Fire Electric...
- Page 12 Sensor measurement range Electrical equipment Delay time Operating mode/application Stand-by Operating data Switchgear data: Controller type; ID number; software/firmware Operating hours Pump’s operating hours Switchgear’s switching cycles Pump’s switching cycles Communication Output parameters SSM parameter Set motor speed Diesel WILO SE 01/2014...
- Page 13 Engine oil Diesel Motor temperature thermostat Diesel Cooling water (temperature) Diesel Belt break Diesel False start Electrical equipment Pressure Electrical equipment Mains power supply Electrical equipment Voltmeter Ampere meter Star-delta switching Electrical equipment Installation and operating instructions Wilo SC-Fire Electric...
- Page 14 Resetting the settings to the factory settings Alarm counter Maintenance interval Reset Motor speed Diesel Set motor speed Diesel Minimum speed for “motor in operation” Diesel Reset starting counter Diesel Menu structure: The menu structure of the control system has 4 levels. WILO SE 01/2014...
- Page 15 English Navigation in the individual menus as well as the parameter input are described in the following example (selecting the transformer): Installation and operating instructions Wilo SC-Fire Electric...
- Page 16 The EXPERT menu contains other settings that can be used for a detailed setting of the switch- gear. The parameter menu for all settings that influence operation. The setting menu for the electrical parameters of the connected pump. Setting the supply voltage. WILO SE 01/2014...
- Page 17 Setting the duration for monitoring of the pump’s 0..70..120 hydraulic output (hydraulic false start). The setting menu for the delays. Start delay when pressure switch trips 1..10 Start delay when float switch trips 1..10 Installation and operating instructions Wilo SC-Fire Electric...
- Page 18 Delay in event of error message from current 0..1..20 monitoring Star-delta changeover time 0..5..60 Buffer time between deactivation of star contac- 0.00..0.05..1.0 tor and activation of delta contactor Communication Display of currently activated fieldbus OFF, Modbus, BAC- net, GSM Pump menu WILO SE 01/2014...
- Page 19 Factory setting Drives on/off OFF, ON Information Current operating values Voltage values Voltage between conductors L1 and L2 Voltage between conductors L1 and L3 Voltage between conductors L2 and L3 Current values Installation and operating instructions Wilo SC-Fire Electric...
- Page 20 English Menu Display Description Parameter range no./ Factory setting Pump current in L1 Pump current in L2 Pump current in L3 Output values Pump output L1 Pump output L2 Pump output L3 Status information WILO SE 01/2014...
- Page 21 Factory setting System status or readiness Status of pressure switch Status of float switch Operating data Total running time of the system Total running time of pump Unit switching cycles Pump’s switching cycles Installation and operating instructions Wilo SC-Fire Electric...
- Page 22 English Menu Display Description Parameter range no./ Factory setting System data System type Serial number as ticker format Software version Firmware version Settings Sensor settings Transformer selection 30..1000 WILO SE 01/2014...
- Page 23 0..10 Lower tolerance limit for rated pump current 0..10 Upper tolerance limit for rated pump current 0..10 Setting for minimum output necessary for detec- 0..80..100 tion that pump has started Signal output parameters Installation and operating instructions Wilo SC-Fire Electric...
- Page 24 Acknowledgement process for fault signal Not store, ON store Logic reversal of input signal Fall, Rise Activation of configurable fault signal OFF, ON Fault active: Ever, Pump Always Only when pump in operation Response delay 0..60 Fault signals WILO SE 01/2014...
- Page 25 Pump operation Menu level 7.0.0.0 is reserved for Wilo customer The signal lamp (Fig. 2, item 2) lights up green if service. the pump is activated and the pump current is within the configurable tolerance range (see menu •...
- Page 26 Therefore, measures may be necessary before the switchgear with pump can be operated as intended at this connection. The necessary information must be obtained from the local electricity supply company and the manufacturer. WILO SE 01/2014...
- Page 27 0.027 15.0 0.024 15.0 0.017 3~400 V 0.252 2-pole 0.220 S-D starting 0.198 0.217 0.157 0.130 0.113 9.0 – 11.0 0.136 9.0 – 11.0 0.098 9.0 – 11.0 0.081 9.0 – 11.0 0.071 Installation and operating instructions Wilo SC-Fire Electric...
-
Page 28: Maintenance
9 Maintenance and factory preset. Have maintenance and repair work carried out The factory settings can be restored by Wilo cus- by qualified skilled personnel only! tomer service. DANGER! Risk of fatal injury! - Page 29 E109.0 Freely configurable fault Depending on the fault configu- Depending on the fault config- ration uration If the fault cannot be remedied, please contact your nearest Wilo customer service point or rep- resentative. Installation and operating instructions Wilo SC-Fire Electric...
- Page 32 WILO SE Nortkirchenstraße 100 D-44263 Dortmund Germany T +49(0)231 4102-0 F +49(0)231 4102-7363 wilo@wilo.com Pioneering for You www.wilo.com...
Need help?
Do you have a question about the Control SC-Fire Electric and is the answer not in the manual?
Questions and answers