Related Manuals for HNE HiPRESS 50 COLD METAL
Summary of Contents for HNE HiPRESS 50 COLD METAL
- Page 1 OPERATING INSTRUCTIONS COLD METAL MOBILE MAGNESIUM EXTINGUISHER www.hne.ag MADE IN GERMANY...
-
Page 2: Table Of Contents
7 - 8 Applying the system......Foldable push handle......Wheel brakes........Jet gun..........11 - 12 Service and maintain......Legal inspections........ Pressure safety........Technical data........Exploded drawing....... Replacement parts......Warranty........... Declaration of conformity..... Contact..........Servicing notes........www.hne.ag MADE IN GERMANY... -
Page 3: Important Basic Information
Without our written permission, no content of this manual shall be reproduced or forwarded to others. All technical specifications and illustrations are subject to copyright. Technical modifications are subject to change without notice. www.hne.ag MADE IN GERMANY... -
Page 4: Symbols And Warnings
Extinguisher with bottle holder, hose and jet gun • Steel pressure cylinder (CFRP optional), 6.8 Liters/300 bar • Plastic bottle with foam concentrate, portioned for first filling • Ergonomic backpack, already mounted (optional) • Second bottle holder for breathing apparatus (optional) • www.hne.ag MADE IN GERMANY... -
Page 5: Device Overview
MADE IN GERMANY... -
Page 6: Storage
HNE to registered customers only. DANGER: Use "HNE Cold Metal" in undiluted concentration only! Any addition of other fluids, especially water will result in explosive reactions upon contact with burning metal. www.hne.ag MADE IN GERMANY... -
Page 7: Filling
Use a suitable container to dispose of it in an environmentally friendly way. We recommend to mark the extinguisher after filling as ready for use. For example, a paper seal can state the date and type of extinguishing agent. www.hne.ag MADE IN GERMANY... -
Page 8: Filling
HiPRESS 50 - COLD METAL Amount and mixing ratio: The container requires a total filling of exactly 50.0 liters of "HNE-Cold Metal". The specialized extinguishing media comes ready for use. Never dilute or mix it with any other fluids. Venting the system: Relieve the system always completely from residual pressure before opening the container lid. -
Page 9: Replacing The Pressure Bottle
The remaining capacity of the air cylinder is still sufficient. Refill or replace the bottle in case of recurrence. Never overfill an air cylinder. Maximum pressure: 300 bar. Use approved pressure bottles of same size only. www.hne.ag MADE IN GERMANY... - Page 10 Close the retaining strap to fix the air cylinder. To avoid accidental opening and to indicate readiness, we recommend marking the hand wheels of filled cylinders with paper seal. www.hne.ag MADE IN GERMANY...
-
Page 11: Applying The System
Take the jet gun from its the triggering lever upward holding clamp and uncurl into unlocked position. the hose. The device is now ready for operation. Users must be sufficiently familiar with the device by instruction and training. www.hne.ag MADE IN GERMANY... -
Page 12: Foldable Push Handle
To unlock, lift the flap with the shoe tip from underneath. Lock the brakes always on both wheels to prevent the device from turning around its own axis. www.hne.ag MADE IN GERMANY... -
Page 13: Jet Gun
● Never aim directly at people or living animals. ● Hazard of suffocation under a layer of foam. Caution when jetting into electrical installations ! Keep a minimum safety distance of 2 Meters within the limit of 1000 Volts ! www.hne.ag MADE IN GERMANY... - Page 14 Secondary tube in upper position Do not change the jet mode while the gun is actuated! • First release the jet gun trigger. • Turn the tubes fully into opposite position. • Then press the trigger again. www.hne.ag MADE IN GERMANY...
-
Page 15: Service And Maintain
NOTE: As a highly safety-relevant element, the pressure reducer is absolutely maintenance-free. Any work or repair at it is solely reserved for HNE. Unauthorized action leads to the complete loss of warranty. After maintenance or repair, the extinguisher should be labeled with filling date and content. -
Page 16: Legal Inspections
The safety valve is precisely adjusted and sealed. Do not adjust or work at it with tools. If the safety valve is responding, only the effect, not the cause of excess pressure is eliminated. The device must be checked thoroughly before next use. www.hne.ag MADE IN GERMANY... -
Page 17: Technical Data
The device is suitable for fighting regular fires only to a limited extent! Small initial fires in the vicinity of burning metal may be extinguished. Sturdy footwear, protective clothing and face protection are required for safe application! www.hne.ag MADE IN GERMANY... -
Page 18: Exploded Drawing
HiPRESS 50 - COLD METAL Exploded drawing www.hne.ag MADE IN GERMANY... -
Page 19: Replacement Parts
AFFF 6%, 3 liter mixing chamber HiPRESS 50 mixing chamber HiCAFS 50 mixing chamber VARIO 50 O-Rings for selector stud VARIO 50 www.hne.ag MADE IN GERMANY... -
Page 20: Warranty
... relevant instructions in this manual have been disregarded If a recognized warranty case occurs, the decision for replacement or repair of single components or the entire device lies solely with HNE. Incurred costs for replacement parts, repair and transportation are assumed by HNE. www.hne.ag... -
Page 21: Declaration Of Conformity
HiPRESS 50 - COLD METAL DECLARATION OF CONFORMITY Directive: 97/23/EG/EEC, Annex VII Type: mobile foam extinguisher HiPRESS 50 Cold Metal Drawing number. : 337 822 / 337 823, 0036 Certification no.: Z-IS-DDB-MUC-15-05-705893-001d Alter Postweg 96, D-86159 Augsburg declare our sole responsibility that the device specified with type,... -
Page 22: Contact
CONTACT HNE Technologie AG HIGH PERFORMANCE FIREFIGHTING SYSTEMS THANK YOU FOR USING OUR PRODUCT! In case of questions or technical problems, please contact our customer service and have type, date of manufacture and serial number of the device ready. HNE Germany: Sales &... -
Page 23: Servicing Notes
Date of manufacture: ________________ please look at container and fill in Proper inspection and repair are crucial for reliability and optimal life span of the device. For traceability, we recommend to document such measures on this page. www.hne.ag MADE IN GERMANY... - Page 24 OPERATING INSTRUCTIONS TECHNOLOGIE AG COLD METAL MOBILE MAGNESIUM EXTINGUISHER SAVING ● PROTECTING ● PRESERVING WORLDWIDE www.hne.ag MADE IN GERMANY...
Need help?
Do you have a question about the HiPRESS 50 COLD METAL and is the answer not in the manual?
Questions and answers