Inserting A Blank Space During Recording (Record Muting); Synchro-Recording With A Cd Player Through A Control A1 Cable - Sony TC-WE725 Operating Instructions Manual

Advanced Recording Operations
Inserting a Blank Space During
Recording (Record Muting)
You can insert a blank space of 4 seconds between each
track. The blank spaces allow you to locate the start of
specific tracks afterwards using the Multi-AMS
function (see page 8). You can also use this function to
erase unwanted portions on a tape.
DIRECTION MODE
A a
RELAY
Ø ON ø OFF
PITCH CONTROL
– +
REC MUTING R
1
Start recording.
2
Press REC MUTING R where you want to insert a
blank space.
"REC" flashes in the display and a blank is
recorded on the tape.
After 4 seconds, P lights up and the tape deck
changes to recording pause.
3
Press PAUSE P to resume recording.
z
If you want to insert a blank space longer than 4
seconds
Hold down REC MUTING R as long as you want.
After 4 seconds, "REC" flashes faster.
When you release REC MUTING R, P lights up and the
tape deck changes to recording pause.
Press PAUSE P to resume recording.
16
PAUSE P
RESET MEMORY A COUNTER B RESET MEMORY
g
DUBBING A B
RMS AUTO CAL(STARTP)
RMS/START SET CHECK DISPLAY DECK A DECK B A+B REC HIGH/NORMAL
– RMS + START(DECK BP)
0 (AMS) (AMS) ) 0 (AMS) (AMS) )
ª · ª ·
p p
CLEAR BACK FRONT
DOLBY NR
PAUSE REC MUTE REC OFF ON ON FILTER B C S PAUSE REC MUTE REC
P R r P R r
§ §
Synchro-Recording With a CD
Player Through a Control A1
Cable
By pressing SYNCHRO, you can perform synchro-
recording on your tape deck with a Sony CD player
connected to the CONTROL A1 connector through an
optional control A1 cable (see page 4). The control A1
cable supports advanced functions not possible with
the commander-based CD synchro-recording function
on previous models. Further information on the
AUTO REC LEVEL
5 various operations made possible by a control A1 cable
4
6
3 7
2 8
1 9
0 10 is provided in the pamphlet attached to this manual.
FADER ARL
π SYNCHRO
PHONES
DIRECTION MODE
DIRECTION MODE
A a
RELAY
Ø ON ø OFF
PITCH CONTROL
– +
1
Set the source selector on the amplifier to CD
player.
2
Insert a CD into the CD player.
3
Select the play mode (CONTINUE, SHUFFLE, or
PROGRAM) of the CD player.
4
Insert a cassette into deck B.
5
Select the side(s) to be recorded on.
To record on
Only one side
Both sides
6
Select the side you want to start recording from
on deck B.
To record from
The front side
The reverse side
ª / ·
SYNCHRO
RESET MEMORY A COUNTER B RESET MEMORY
AUTO
4
3
2
g 1
DUBBING A B
RMS AUTO CAL(STARTP) 0
RMS/START SET CHECK DISPLAY DECK A DECK B A+B REC HIGH/NORMAL
– RMS + START(DECK BP)
FADER
0 (AMS) (AMS) ) 0 (AMS) (AMS) )
π SYNCHRO
ª · ª ·
p p
CLEAR BACK FRONT
DOLBY NR
PAUSE REC MUTE REC OFF ON ON FILTER B C S PAUSE REC MUTE REC
PHONES
P R r P R r
§ §
Set DIRECTION MODE to
A
a or RELAY
Press
·
ª
REC LEVEL
5
6
7
8
9
10
ARL