Related Manuals for RF Technologies Sensatec ST710
Summary of Contents for RF Technologies Sensatec ST710
- Page 1 ST710 Instruction Manual PN 0510-0519-B Release Date 11/17/17 3125 North 126 Street, Brookfield, WI 53005 USA phone: 800.669.9946 web: www.rft.com...
-
Page 2: Table Of Contents
Contents CONTENTS ............................2 SAFETY INSTRUCTIONS ........................INTENDED USE ..........................CONTRAINDICATIONS ........................POTENTIAL ELECTROMAGNETIC OR OTHER INTERFERENCE ................ BEFORE USING THE ST710 ........................ ENVIRONMENTAL R E Q UIREMENTS ...................... 3 SAFETY INFORMATION ........................TERMS ............................3 WARNINGS ........................... 4 CAUTIONS ............................. 4 ST710 CONTROL UNIT ......................... -
Page 3: Safety Instructions
Before Using the ST710 Intended Use • Be sure to read the Instruction Manual thoroughly The SENSATEC ST710 fall monitor, monitors a bed, before using to get a full understanding of the chair, or room for occupancy. When mounted on a ST710. -
Page 4: Warnings
& Warnings (continued) Example of Picture Indication Do not recharge batteries Important precautions Explosion and liquid leak of battery may lead to fire and injury. Inspect the plug and the outlet regularly Must follow the instructions Remove the dust and dirt between the plug and the outlet regularly. - Page 5 cautions (continued) Battery caution Follow the instruction below. Failure to do so may lead to battery explosion and liquid leak of battery. This may lead to fire and injury, or cause damage to the surrounding area. • Use only approved battery types . •...
-
Page 6: St710 Control Unit
ST710 Control Unit Front Side Inside Battery Box (continued) Volume Switch Hold button with red and green LED Alarm volume switch. (H , M , L) • = High volume • = Medium volume • Sensor input jack = Low volume. Delay Time Switch Alarm time delay setting to avoid unnecessary alarm caused by patient's tossing and turning. -
Page 7: Using The St710 System
Usin the ST710 S stem Bed Mode Chair Mode Place the bed sensor pad just below the patient's back, Plug the sensor cable into the ST710 sensor jack. underneath the sheets, overlays or incontinent pads. If Make sure the cable will not interfere with the early detection is necessary, place the sensor pad chair wheels or movable chair components and below the patient's shoulder. -
Page 8: Floor Mode
Chair Mode (continued) Floor Mode Toilet Sensor Pad Do not connect a bed or chair sensor and floor mat sensor cable to the ST710 at the Place the toilet sensor pad underneath the toilet seat (as same time. Operation of the bed/chair sensor per the instruction on the toilet pad) when seated. -
Page 9: Selecting A Tone For The Alarm
Mounting Attachments Selecting a Tone for the Alarm The ST710 can be fitted with the following attachments: Tone starts and continues sounding when you press Strap and hold the Sound select button. Release the button The strap is attached to the ST710 through a strap hole and and then press the button again to listen to the next can be attached to a bed, chair or handrail. -
Page 10: Testing The System And Troubleshooting
Testin the S stem and Troubleshootin Testing the System Troubleshooting Test ST710 and sensor pad for proper Sensor Pad Cannot Detect Movement operation before each use and inspect for an y When the sensor pad cannot detect the patient's signs of damage or excessive wear. movement because she/he is too lightweight: •... -
Page 11: Specifications
24Hrs. (Alarm: 20sec., volume max., 5 times/day) Without protective silicon boot, with batteries Accessories The SENSATEC ST710 monitor can be used with the following SENSATEC sensor pad and mats: Sensor Pads • RFT#l000-1801 - 30 Day Bed Pad • RFT#l000-1802 - 90 Day Bed Pad •...
Need help?
Do you have a question about the Sensatec ST710 and is the answer not in the manual?
Questions and answers