Table of Contents
Related Manuals for Eriez HD-46C
Summary of Contents for Eriez HD-46C
- Page 1 VM-3169B Installation, Operation and Maintenance Instructions VIBRATORY FEEDERS MODELS - HD-46C, HD-56C, & HD-66C ERIEZ WORLD HEADQUARTERS: 2200 ASBURY ROAD, ERIE, PA 16506–1402 U.S.A. WORLD AUTHORITY IN SEPARATION TECHNOLOGIES...
- Page 2 Introduction This manual details the proper steps for installing, operating and maintaining the Eriez Vibratory Feeder. Careful attention to these requirements will assure the most efficient and dependable performance of this equipment. If there are any questions or comments about the manual, please call Eriez at 814/835-6000 for Vibratory Feeder assistance.
-
Page 3: Table Of Contents
Table of Contents ERIEZ VIBRATORY FEEDER - MODELS HD-46C, HD-56C & HD-66C INSTALLATION ..................... 4 Mounting ......................4 Electrical Connections ..................4 OPERATION AND MAINTENANCE ..............4 Tuning Guide ....................4 Tuning for Non-Standard Trays ............... 5 Tuning for Different Conditions of Tray Loading ..........6 REPAIRS ....................... -
Page 4: Installation
ELECTRICAL CONNECTIONS of the vibratory elements. NOTE: The Eriez Vibratory HD-C Feeder is designed to be IMPORTANT NOTE: operated from an AC source through a special Eriez 30Hz Special Trays and Attachments control (see IOM - 414). -
Page 5: Tuning For Non-Standard Trays
Figure 2 displacement. How to Measure Displacement Position an Eriez displacement sticker on the outer side As a guide to the stiffness of individual tuning springs, of the tray, near the rear of the tray and at an angle of each spring is marked with a code number example, 25°... -
Page 6: Tuning For Different Conditionsof Tray Loading
Do not allow hands, fingers and other body parts more than .219" (5.6 mm) without load for HD-46C, to be caught between the equipment and nearby HD-56C and HD-66C. -
Page 7: Coil Replacement
BODY HOUSING Figure 5 Figure 7 4. If the coil is defective, the entire E-frame assembly FEEDER AIR GAPS including the coil must be replaced (order from Eriez parts list). HD-46C HD-56C HD-66C 5. In reassembling the unit, first center the armature at the bottom of the body cavity;... -
Page 8: Spring Replacement
The following applies: SPRING CHANGE OR MODEL REAR SPRINGS/PLY FRONT SPRINGS/PLY REPLACEMENT HD-46C 2-13 ply, 1-9 13 ply Refer to the Parts List Drawing and Figs. 8 & 9. Although the non-metallic springs used in the HD-56C 4-13 ply... -
Page 9: Armature Replacement
TABLE 1. TORQUE CHART 5. Stand the armature and spring stack assembly on a 46 & 56 Series non-magnetic surface (I.E. wooden table) as shown in Figure 9. NOTE: Keep armature away from any Torque Part Bolt steel parts and surfaces. Size m-kgs ft-lbs... - Page 10 The engine-driven power plant is shut down. new Hi-Vi method incorporates a lifetime permanent rare earth magnet and is operated directly from an alternating current line through Eriez 30Hz control. POTENTIOMETER In the Hi-Vi method, the spring-mounted mass is POWER...
-
Page 11: Troubleshooting
7. Spring Failure may have affected performance. Reassemble in See maintenance instructions. Disassemble for accordance with printed instructions or consult Eriez. examination. Tuning spring failure will show up 3. Loose Spring Clamp or Tray Mounting Bolts as white areas. Order new parts from factory and Tighten all bolts. - Page 12 If product density, moisture content or other characteristics vary, customer should take own corrective measures. Eriez and Eriez Magnetics are registered trademarks of Eriez Manufacturing Co, Erie, PA ©2019 Eriez All Rights Reserved World Authority in Separation Technologies ...
Need help?
Do you have a question about the HD-46C and is the answer not in the manual?
Questions and answers