Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Loctite 98022
Summary of Contents for Loctite 98022
- Page 1 EQUIPMENT Operation Manual Loctite® 300ml Cartridge Pusher Part Number 98022...
-
Page 2: Table Of Contents
Table Of Contents ..................3 LEASE BSERVE OLLOWING ..........................3 MPHASIZED ECTIONS ............................3 AFETY ............................3 TEMS UPPLIED ......................... 4 ESCRIPTION ..........................4 ESCRIPTION OF 2.2 T ..................... 4 HEORY OF PERATION ......................... 5 ECHNICAL ........................6 NSTALLATION ........................... 6 ISPENSING ......................7 ETTING EVEL NDICATOR ......................7... -
Page 3: Please Observe The Following
Observe general safety regulations for the handling of chemicals such as Loctite® adhesives and sealants. Observe the manufacturer’s instructions as stated in the Material Safety Data Sheet (MSDS). While under warranty, the unit may be repaired only by an authorized Loctite® service representative. Items Supplied Carefully remove the unit from its shipping carton and inspect it for any signs of damage. -
Page 4: Description
Air Supply Port Theory of Operation The 300 ml Cartridge Pusher 98022 is used to dispense Loctite® medium viscosity adhesive from 300 ml cartridges. The cartridge pusher is a front loaded, freestanding device that can be coupled with a Loctite® Single Function Controller 98023, Three Function Controller 98024 or integrated into an existing work cell. -
Page 5: Technical Data
This switch is equipped with an LED indictor and a connector has been installed to interface with Loctite® Single Function Controller 98023 or Three Function Controller 98024. The reed switch is activated by a permanent magnet located on the piston within the air cylinder. -
Page 6: Installation
Installation 1. The 300ml cartridge pusher is designed to be mounted vertical or horizontal position. The vertical position is preferred. See drawing for hole locations. 2. Install airline to regulator using a 1/8” NPT fitting. Rocky Hill, Connecticut 06067 Model No. Serial... -
Page 7: Dispensing
If dispensing is to be stopped for a prolonged period of time shut total system down and remove 300 ml cartridge from sleeve. Every 3 – 6 weeks, Loctite® ViperLube™ Grease should be pumped into grease fitting located on cylinder mount/grease reservoir (item 9). -
Page 8: Troubleshooting
Reed Switch Assembly 984756 Air Cylinder 984732 Plunger Ram 984755 Optional Accessories Loctite® ViperLube™ Grease 14 oz. Cartridge 36782 Cartridge Fitting Kits: Poly Fitting 1/4” Tube x 1/4 Male NPT, Qty 10 984832 Poly Fitting 3/8” Tube x 1/4 Male NPT, Qty 10 984833 Fischbach cartridge to 1/4 Female NPT, S.S., Qty. -
Page 9: Wiring Diagram
Henkel expressly warrants that all products referred to in this Instruction Manual for The 300 ml Cartridge Pusher 98022 (hereafter called “Products”) shall be free from defects in materials and workmanship. Liability for Henkel shall be limited, as its option, to replacing those Products which are shown to be defective in either materials or workmanship or to credit the purchaser the amount of the purchase price thereof (plus freight and insurance charges paid therefor by the user). - Page 10 Madison Heights, MI 48071 Diadema/SP, Brazil www.loctite.com Loctite is a registered trademark of Henkel Corporation, U.S.A © Copyright 2003. Henkel Corporation. All rights reserved. Data in this operation manual is subject to change without notice. Manual P/N: 984744, Rev B, 08/2008...
Need help?
Do you have a question about the 98022 and is the answer not in the manual?
Questions and answers