Advertisement
Available languages
Available languages
ATCU Throttle Control Unit
Unité ATCU de commande des gaz
ATCU/1
ATCU/1+
Installation and Maintenance Instructions
Instructions d'installation et de maintenance
English - page 1
Francais - page 5
Tel: +44 (0)1983 295555
email: prosupport@spinlock.co.uk
3R334A/0
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Spinlock ATCU/1
Summary of Contents for Spinlock ATCU/1
- Page 1 ATCU Throttle Control Unit Unité ATCU de commande des gaz ATCU/1 ATCU/1+ Installation and Maintenance Instructions Instructions d’installation et de maintenance English - page 1 Francais - page 5 Tel: +44 (0)1983 295555 email: prosupport@spinlock.co.uk 3R334A/0...
- Page 2 Check carefully in front and behind the surface on which you intend mounting the control unit. Ensure that the control unit will fit and the cables are able to be lead away without sharp bends that might affect the operation of the unit. Check the winch handle or Spinlock control lever for un-restricted travel.
- Page 3 ATCU – Throttle Control Unit Installation Checklist •Pre-assemble whole unit before fitting / drilling deck. •Check gear engagement and throttle in neutral.(button depressed). •Check forward and reverse propulsion before casting off. •Max.deck thickness = 30mm. •Mount faceplate first, ensuring `O` ring is enclosed by back plate onto faceplate. (Refer to Assembly Drawing).
- Page 4 être installée et que les câbles ont suffisamment de place pour arriver sans être pliés de façon trop importante, ce qui pourrait affecter la bonne marche de l'appareil. Vérifiez la marche sans entrave du levier de contrôle Spinlock ou de la manivelle dw winch Installation 1) Marquez la position centrale pour la plaque frontale avec le modèle annexé...
- Page 5 Maintenance et protection contre la corrosion Pour une protection optimale, en particulier dans un environnement salin, il est recommandé de laver régulièrement à l’eau douce la plaque frontale, le mamelon et le levier. Vérifiez périodiquement le mécanisme de la tête de contrôle pour resserrer les fixations lâches et détecter les traces d’usure des pièces mobiles.
- Page 6 Minimum 2mm protrusion Fig 1. from front face. ( Dépassement d'au moins 2mm de la plaque frontale.) Faceplate (Item 1) Plaque frontale (article 1) Boss (Item 4) Mamelon (article 4) Spacer (Item 11) Espaceur (article 11) 4off - white (blanc) Spacer (Item 7)4 off - Black.
Need help?
Do you have a question about the ATCU/1 and is the answer not in the manual?
Questions and answers
The throttle of my ATCU doesn‘t hold the rpm. How can I make it keep again?
To fix the throttle on your Spinlock ATCU/1 to maintain RPM, follow these steps:
1. Check all throttle operations: Ensure neutral throttling, forward and reverse gear selection, and in-gear throttle are functioning correctly.
2. Align markings: When reassembling, align the white mark on the boss vertically with the white dot on the faceplate while in the neutral setting.
3. Secure components: Use Studlock or Loctite on the three grub screws (set screws) of the boss and tighten them firmly.
4. Lubrication: Make sure all moving metal parts are well-lubricated with a heavy-duty, moisture-repelling grease.
5. Check for wear: Inspect for wear or corrosion on cable and motor connections and replace if needed.
6. Ensure proper engagement: Verify that the lever correctly engages and disengages from the neutral button.
These steps help ensure the throttle holds position and maintains RPM.
This answer is automatically generated