Quick Start; Required Equipment - Maxim MAX16920A General Description Manual

DESIGNATION QTY
U1 1
— 10
— 1
ADDITIONAL COMPONENTS FOR MAX16920A
EVALUATION
— 3
SUPPLIER
Cooper Bussmann
Diodes Incorporated
Murata Electronics North America, Inc.
Panasonic Corp.
TDK Corp.
Vishay
Note: Indicate that you are using the MAX16920B when contacting these component suppliers.
• MAX16920B EV kit
• 12V, 2.5A DC power supply
• Four electronic loads (e.g., HP6060B)
• Four voltmeters
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation. Caution: Do not turn on
power supplies until all connections are completed.
1) Verify that all jumpers are in their default position, as
shown in Table 1.
2) Adjust the power supply to 12V and connect to the
VIN and PGND PCB pads on the EV kit.
3) Adjust the first load to 150mA and connect to the
OUT1 and PGND1 PCB pads on the EV kit.
4) Connect the first voltmeter to the OUT1 and PGND1
PCB pads on the EV kit.
_________________________________________________________________ Maxim Integrated Products 2
Evaluates: MAX16920A/MAX16920B
DESCRIPTION
Power-management IC
(32 TQFN-EP)
Maxim MAX16920BATJ/V+
Shunts
PCB: MAX16920B EVALUATION
KIT+
22FF Q10%, 10V X7R ceramic
capacitors (1206)
Murata GRM31CR71A226K

Quick Start

Required Equipment

Procedure
MAX16920B Evaluation Kit
Component List (continued)
DESIGNATION
—
—
—
—
PHONE
916-941-1117 www.cooperet.com
805-446-4800 www.diodes.com
770-436-1300 www.murata-northamerica.com
800-344-2112 www.panasonic.com
847-803-6100 www.component.tdk.com
402-563-6866 www.vishay.com
5) Adjust the second load to 600mA and connect to the
OUT2 and PGND2 PCB pads on the EV kit.
6) Connect the second voltmeter to the OUT2 and
PGND2 PCB pads on the EV kit.
7) Adjust the third load to 1.5A and connect to the OUT3
and PGND3 PCB pads on the EV kit.
8) Connect the third voltmeter to the OUT3 and PGND3
PCB pads on the EV kit.
9) Adjust the fourth load to 150mA and connect to the
OUTA and GND PCB pads on the EV kit.
10) Connect the fourth voltmeter to the OUTA and GND
PCB pads on the EV kit.
11) Connect the SYNC and GND PCB pads on the EV kit
together.
12) Turn on the DC power supply.
13) Enable all loads.
14) Verify that the first voltmeter reads approximately 3.3V.
15) Verify that the second voltmeter reads approximately 5V.
16) Verify that the third voltmeter reads approximately 3.3V.
17) Verify that the fourth voltmeter reads approximately 5V.
QTY DESCRIPTION
47FF Q10%, 10V X7R ceramic
1 capacitor (1210)
Murata GRM32ER71A476K
47FH, 1.14A inductor
1 (7.60mm x 7.60mm x 4.35mm)
Cooper Bussmann DRA74-470-R
22FH, 1.68A inductor
1 (7.60mm x 7.60mm x 4.35mm)
Cooper Bussmann DRA74-220-R
10FH, 2.56A inductor
1 (7.60mm x 7.60mm x 4.35mm)
Cooper Bussmann DRA74-100-R
Component Suppliers
WEBSITE