Table of Contents
Advertisement
Quick Links
CLEAN
5
5
5
4
6
4
6
4
6
3
7
3
7
3
2
8
2
8
2
1
9
1
9
1
0
10
0
10
0
10
GAIN
LOW
HIGH
20W Tube Guitar Amplifier
LEAD
5
5
5
4
6
4
6
4
7
3
7
3
7
3
8
2
8
2
8
2
CHANL
GATE
9
1
9
1
9
1
0
10
0
10
0
PRE GAIN
LOW
MID
TIGHT
BOOST
Peavey
Invective
®
invective
MASTER
5
5
5
6
4
6
4
6
4
6
4
7
3
7
3
7
3
7
3
8
2
8
2
8
2
8
2
9
1
9
1
9
1
9
1
10
0
10
0
10
0
10
0
HIGH
POST GAIN RESONANCE PRESENCE
MH
®
Operating
Manual
. MH
TSI™ T2
T1
EL84
5
ON
ON
6
7
8
9
10
STANDBY
POWER
www.peavey.com
Advertisement
Table of Contents
Related Manuals for Peavey Invective MH
Summary of Contents for Peavey Invective MH
- Page 1 Peavey Invective ® ® 20W Tube Guitar Amplifier Operating Manual invective . MH TSI™ T2 EL84 CLEAN LEAD MASTER CHANL GATE INPUT GAIN HIGH PRE GAIN HIGH POST GAIN RESONANCE PRESENCE TIGHT BOOST STANDBY POWER www.peavey.com...
- Page 2 (2) I’utilisateur de I’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Warning: Changes or modifications to the equipment not approved by Peavey Electronics Corp. can void the user’s authority to use the equipment.
- Page 3 ® Congratulations on the purchase of your new Invective MH tube guitar amplifier from Peavey! Although small, this amp has an all- tube preamp and power amp to authentically produce the much loved tones of the Invective 120-- albeit at lower power levels. The major advantage is the sheer size and weight (or lack thereof).
- Page 4 Invective MH ® Front Panel invective . MH TSI™ T2 EL84 CLEAN LEAD MASTER CHANL GATE INPUT GAIN HIGH TIGHT BOOST PRE GAIN HIGH POST GAIN RESONANCE PRESENCE STANDBY POWER INPUT Standard 1/4” jack for connection to the output of your guitar or last pedal if using effects before the amp.
- Page 5 Invective MH ® Front Panel cont. POST-GAIN controls This controls the output level of the LEAD channel. Used to set the volume as well as to balance the sound between the two channels. RESONANCE and PRESENCE Allows for adjustment of the damping factor of the power amplifier. Damping is the ability of an amplifier to control speaker cone motion after the signal disappears.
- Page 6 ® Invective MH Front Panel cont. POWER switch To apply power to the unit, connect the line cord and flip the switch to the ON position. Three of the four front panel LED’s should illuminate, indicating power is being supplied. It’s best that the STANDBY switch (12) is set to STANDBY when amp is first switched on.
- Page 7 Invective MH ® Rear Panel MSDI 20W RMS/ 17.9V RMS SEND CHNL/TIGHT (MIC SIMULATED DIRECT INTERFACE) MIN. A PRODUCT OF SPKR GRND PEAVEY ELECTRONICS CORP. OUTPUT LIFT DESIGNED AND ENGINEERED IN U.S.A. MADE IN CHINA ENABLE RETURN BST+GATE/LOOP DEFEAT GRND...
- Page 8 The load impedance is selectable via the IMPEDANCE SELECTOR (18). The Invective MH sounds great into a 1x12, but try this into a 4x12 and see the reaction you get! DO NOT connect a speaker while the power is turned on!
- Page 9 If the effects loop is used, then it will automatically be on. However, a footswitch can also be used to bypass the effects loop-- see below. FOOTSWITCH JACKS Provides for connection of one or two Peavey Multi-purpose 2-button Footswitch w/LEDs (#03022910). One such footswitch is included with the amplifier. Top Jack (CHNL/TIGHT): “1”...
- Page 10 ® Invective MH All-Tube Guitar Amplifier SPECIFICATIONS Rated Power: 20 W(rms) into 8 or 16Ω A second footswitch can be used for turning Boost + Gate and/or effects loop on and off. Power Consumption: (Domestic) 90 Other Misc Specifications W, 50/60 Hz, 120 VAC...
- Page 12 Warranty registration and information for U.S. customers available online at www.peavey.com/warranty or use the QR tag below Features and speci cations subject to change without notice. Peavey Electronics Corporation 5022 Hartley Peavey Drive Meridian, MS 39305 (601) 483-5365 FAX (601) 486-1278 Logo referenced in Directive 2002/96/EC Annex IV (OJ(L)37/38,13.02.03 and defined in EN 50419: 2005...