Related Manuals for Franklin Electric FHOTON
Summary of Contents for Franklin Electric FHOTON
- Page 1 FHOTON AC/DC Power Converter Installation Guide...
- Page 2 SWIMMING AREAS. CAUTION Use the Fhoton AC/DC Power Converter only with Fhoton Drive controllers up to 1.5HP (see Specifications page) and Franklin Electric motors as indicated in the Fhoton Drive controller installation guide. Use of this unit with any other Franklin Electric motor or with motors from other manufacturers may result in damage to both motor and electronics.
- Page 3 Electric Fhoton Drives having model numbers 581013000XXX-X or 581014200XXX-X, with ratings of up to, and including 1.5 hp. It is not to be used with Fhoton drives having ratings of 2 hp or higher, or, with products made by other manufacturers.
-
Page 4: Protection Features
Use of External Transfer Switches The output of the Fhoton AC/DC Power Converter is to be connected directly to the input power terminals of the noted Fhoton Drive Models. No other devices or connections should be combined with the output connections. - Page 5 Input and Flow Switch Input. If removed, the output of the Fhoton AC/DC Power Converter will switch to a high impedance state disabling the Fhoton Drive. In this case, the LED will be solid green indicating that it is in IDLE condition, awaiting to be enabled by reinstating the jumper.
- Page 6 Over Temperature Shutdown (Seven Flash Red LED Sequence) The Fhoton AC/DC Power Converter is designed for full power operation from a DC or AC power source in ambient temperatures up to 122 °F (50 °C). Under extreme thermal conditions the AC/DC Power Converter output state will change to a high impedance state to limit the output current.
-
Page 7: Wiring Connections
Fhoton Drive making sure to match the polarity designation as shown in the figure below. (Torque specification: 15 in-lbs/ 1.7 N-m). (Use copper conductors only. Rated 75 °C minimum.) The output cabling to the Fhoton Drive shall not exceed 30 ft (10 m). Note: The Fhoton AC/DC Power Converter output is polarity sensitive. -
Page 8: Fault Codes And Troubleshooting
An error code is displayed by the flashing red LED light. If the Fhoton AC/DC Power Converter has stopped to indicate a fault code, the associated time-out delay will vary depending on the nature of the fault. - Page 9 10Adc Short Circuit Trip Level Efficiency at Max Power Models 58101300 or 58101420 followed Use with these Franklin Electric by any sequence of numbers or Fhoton Drive Models, only characters up to and including 1.5 hp Controller Size L x W x D Millimeters 159.5 x 159.5 x 185.8...
- Page 10 AC/DC Power Converter Schematic CURRENT DC VOLTAGE SENSOR AC OR DC OUTPUT TO VOLTAGE INPUT FHOTON DRIVE CONTROL CIRCUIT INPUT OUTPUT CONTROL CURRENT TERMINAL TERMINAL CIRCUIT SENSOR BLOCK BLOCK EARTH EARTH CHASSIS EARTH Circuit Operation The power source connected to the input terminal block on the left side is directed to a full-wave rectification circuit which converts AC to DC power.
- Page 11 AC/DC Power Converter Outline Dimensions AC/DC Power Converter G.1* Dimensions Inches 8.17 6.28 6.10 4.88 7.40 6.28 7.32 3.30 1.38 1.38 4.94 Millimeters 207.55 159.4 159.4 185.82 83.82 125.47...
- Page 12 FE USA Technical Service Hotline 1.800.348.2420 9255 Coverdale Road, Fort Wayne, IN 46809 Tel: 260.824.2900 Fax: 260.824.2909 www.franklinwater.com 224455101 Rev. 1 03.18...
Need help?
Do you have a question about the FHOTON and is the answer not in the manual?
Questions and answers