Kenwood NX-200 Service Manual page 60

NX-200(G)
Item
Panel tuning mode
High RSSI 1) Adj item: [Nv
at –80dBm HRSSI]
adjust *8 Adjust: [‫]٭٭٭‬
2) Adj item:
[NXDN [NvL HRSSI]→
Very [NvL' HRSSI]→
Narrow] [NvC HRSSI]→
[NvH' HRSSI]→
[NvH HRSSI]
Adjust: [‫]٭٭٭‬
SSG output:
–80dBm (22.4µV)
(MOD: 1kHz/±1.5kHz)
*8: Because High RSSI at –80dBm (NXDN Narrow) is adjusted by adjusting High RSSI at –80dBm (Analog Narrow), it is not necessary to adjust
High RSSI at –80dBm (NXDN Narrow).
8. Tight 1) Adj item: [An SQLT]
Squelch Adjust: [‫]٭٭٭‬
adjust 2) Adj item:
(Squelch [AnL SQLT]→
level 9 [AnL' SQLT]→
adjust) [AnC SQLT]→
[AnH' SQLT]→
[Analog [AnH SQLT]
Narrow] Adjust: [‫]٭٭٭‬
SSG output: 12dB
SINAD level +5dB
(MOD: 1kHz/±1.5kHz)
[Analog 1) Adj item: [Aw SQLT]
Wide] Adjust: [‫]٭٭٭‬
2) Adj item:
[AwL SQLT]→
[AwL' SQLT]→
[AwC SQLT]→
[AwH' SQLT]→
[AwH SQLT]
Adjust: [‫]٭٭٭‬
SSG output: 12dB
SINAD level +5dB
(MOD: 1kHz/±3kHz)
60
ADJUSTMENT
Condition
PC test mode
equipment
1) Adj item: [High SSG
RSSI (NXDN Very
Narrow)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output:
–80dBm (22.4µV)
(MOD: 1kHz/±1.5kHz)
1) Adj item: [Tight SSG
Squelch (Analog
Narrow)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output: 12dB
SINAD level +5dB
(MOD: 1kHz/±1.5kHz)
1) Adj item: [Tight
Squelch (Analog
Wide)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output: 12dB
SINAD level +5dB
(MOD: 1kHz/±3kHz)
Measurement
Test-
Unit Terminal Unit
Panel ANT
Universal
connector
Panel ANT
Universal
connector
Adjustment
Specifi cations /
Parts Method
[Panel tuning mode] Adjust with the
After input signal analog signal.
from SSG, press
[ ] key to store the
adjustment value.
[PC test mode]
After input signal
from SSG, press
[Apply] button to
store the adjust-
ment value.
[Panel tuning mode]
After input signal
from SSG, press
[ ] key to store the
adjustment value.
[PC test mode]
After input signal
from SSG, press
[Apply] button to
store the adjust-
ment value.
Remarks