Page 2
A &&A .. A A &&A .! ".) ".A A &&A 8!" "##A A &&A .! ".) ". ##A A &2&A 4/
C#A A &
&A 8 9. ##A A &7&A ". . ##:A A &*&A B# 9. ##A A &$&A
- !"#
-# !A A &&A >.
Page 3
A
&*&A5' .= 5:!A A
&
&A*' 3!# 5:!A A
&&A5' 3!# 5:!A A
&
&A' .= 5:!A A
&&A5' 3!# 5:!A A
&
&A' 3!# 5:!A A
&2&A5'
3!# 5:!A A
&
&A' 3!# 5:!A A
&7&A5' * 3!# 5:!A A
&
*&A5' 3!# 5:!A...
Page 16
! Alignment menu INPUT Equipment Test Point Level Remark Subject Item NTSC Oscilloscope TP8004 VPC SETTING 0.7V+-0.02V DG CONTRAST Colour Bar (3A) 100IRE Oscilloscope TP8004 VPC SETTING DG CONTRAST 0.55V+-0.02V Colour Bar (3A)
...
Page 17
;59
7.
INPUT Equipment Setting Alignment menu Procedure 1 NTSC Color Picture: 1) Find the nearest area to brightness of 5 cd/m as Low Gray Scale Analyzer Normal Sub Adjust light by color sensor. Pattern White balance: Sub Bright 2) Adjust Sub bright to set Low light level to 5 cd/m...
Page 18
,4<89,=
7.
INPUT Equipment Setting Alignment menu Procedure 1 PAL Color Picture: 1) Find the nearest area to brightness of 5 cd/m as Low Gray Scale Analyzer Normal Sub Adjust light by color sensor. Pattern White balance: Sub Bright 2) Adjust Sub bright to set Low light level to 5 cd/m...
Page 19
Equipment Setting Alignment menu Procedure Picture: 1) Write down each color temaparature of R,G,B drive and Normal Cut off data as follows. Aspect: 16:9 White White balance: Balance Cool Normal Warm Cool R Drive Normal G Drive B Drive Warm R Cut off...
Page 20
) INPUT Equipment Setting Alignment menu Procedure ** Adjust at the dark room. 1 Component Picture: PANEL W/B (525i, 525p, 625i, Normal R cut off 1) Set R,G and B cut off to " 80 ". 720i or 1080i) White balance: G cut off...
Page 21
0
7.
INPUT Equipment Setting Alignment menu Procedure 1 PC Color Picture: 1) Find the nearest area to brightness of 5 cd/m as Low Gray Scale Analyzer Normal Sub Adjust light by color sensor. Pattern White balance: Sub Bright 2) Adjust Sub bright to set Low light level to 5 cd/m...
Page 22
INPUT Equipment Setting Alignment menu Procedure Picture: 1) Write down each color temaparature of R,G,B drive and Normal Cut off data as follows. Aspect: 16:9 White White balance: Balance Cool Normal Warm Cool R Drive Gray Scale G Drive Normal Pattern...
Page 23
"
7.
INPUT Equipment Setting Alignment menu Procedure (720i or 1080i) Color Picture: 1) Find the nearest area to brightness of 5 cd/m as Low Gray Scale Analyzer Normal Sub Adjust light by color sensor. Pattern White balance: Sub Bright 2) Adjust Sub bright to set Low light level to 5 cd/m...
Page 24
INPUT Equipment Setting Alignment menu Procedure Picture: 1) Write down each color temaparature of R,G,B drive and Normal Cut off data as follows. Aspect: 16:9 White White balance: Balance Cool Normal Warm Cool R Drive Gray Scale Normal G Drive Pattern...
Page 25
%
INPUT Equipment Setting Alignment menu Procedure 1 625i Color Picture: 1) Find the nearest area to brightness of 5 cd/m as Low Gray Scale Analyzer Normal Sub Adjust light by color sensor. Pattern White balance: Sub Bright 2) Adjust Sub bright to set Low light level to 5 cd/m Cool...
Page 26
'
).
) INPUT Equipment Setting Alignment menu Procedure ** Adjust at the dark room. 1 NTSC Picture: PANEL W/B Gray Scale Normal All cut off 1) Set white balance to Cool . Pattern Aspect: 16:9 2) Adjust All cut off to start some pixels emission at black 2% area and no emission at black 0% area.
Page 27
INPUT Equipment Setting Alignment menu Procedure ** Adjust at the dark room. 4 525i Picture: PANEL W/B Gray Scale Normal All cut off 1) Set white balance to Cool . Pattern Aspect: 16:9 2) Adjust All cut off to start some pixels emission at black 2% area and no emission at black 0% area.