Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tecnolux 12066
Summary of Contents for Tecnolux 12066
- Page 1 HEADLIGHT TESTER ART. 12066 MANUAL FOR USE AND MAINTENANCE...
-
Page 3: Table Of Contents
INDEX ACCEPTANCE OF THE MACHINE ............4 FOREWORD ..................... 4 TECHNICAL DATA ................... 4 SYMBOLS USED IN THE MANUAL ............5 SYMBOLS USED ON THE MACHINE............6 PREPARATION OF THE MACHINE ............7 HANDLING CRATED MACHINE ..................7 CONTENTS OF THE PACKAGE ..................7 DESCRIPTION OF THE MACHINE ............ -
Page 5: Acceptance Of The Machine
ACCEPTANCE OF THE MACHINE At the time of delivery it is essential to check at once and make sure you have received all the material indicated in the shipping documents, and that the machine has not undergone damage during shipment. In this case, show the damage to the forwarder and inform our customer service department. -
Page 6: Symbols Used In The Manual
SYMBOLS USED IN THE MANUAL Warning symbol Read the sections preceded by this symbol with particular care, for the safety of the operator and the machine. -
Page 7: Symbols Used On The Machine
SYMBOLS USED ON THE MACHINE Laser beam Read with care warnings with this symbol for operator safety and machine safety. Pay attention of all warning symbols on the products, keep wholly stickers and fully readable. -
Page 8: Preparation Of The Machine
PREPARATION OF THE MACHINE HANDLING CRATED MACHINE The machine is packed in a special crate. Do not stack more than four crates. The packed weight is 20 kg. The external dimensions are: B: 800 mm L: 600 mm H: 500 mm CONTENTS OF THE PACKAGE N°1 base N°1 column (2 parts) -
Page 9: Description Of The Machine
DESCRIPTION OF THE MACHINE The headlight tester is a device that allows to test headlights of all types, for motor vehicles, cars and trucks in general. The machine can be installed as a moving station on rubber wheels. The optical box is adjustable in height by means of a slider on precise, silent, plastic runners on an aluminum column marked with a centimeter... - Page 10 DESCRIPTION OF THE MACHINE Art. 12066 e Art.12066/S Analogic unit is equipped with a luxmeter with 3 intensity marker ranges: • upper range indicates lux/25m values (lux at 25 meters) • central range indicates klux/1m values (kilo lux at 1 meter and kcd (kilo candles) •...
- Page 11 DESCRIPTION OF THE MACHINE The visor that facilitates the alignment of the device to the vehicle can be equipped with mirror or laser.
-
Page 12: General Safety Rules
GENERAL SAFETY RULES The following rules must be followed carefully to prevent damage to the operator and machine. Read the machine labels, do not cover them for any reason, and replace them immediately if they should be damaged. The device should only be used by authorized personnel, trained in its use. Do not use the device in an explosive atmosphere. -
Page 13: Assembly
ASSEMBLY Open the packaging from the top extracting all parts taking care not to cause violent shocks and damages. 1 – ASSEMBLY OF BOTTOM PART OF THE COLUMN ON THE BASE Bottom half part of the column is already preassembled with the fixing plate on the base. Be careful to orient the column with the graduated scale in the direction of the two in-line wheels of the base as indicated in the picture aside. -
Page 14: Assembly Of The Optical Box Sliding System On The Column
ASSEMBLY 2 – ASSEMBLY OF THE OPTICAL BOX SLIDING SYSTEM ON THE COLUMN Insert the sliding system of the optical box on the bottom part of the column already fixed on the base. In order to facilitate the insert of the sliding system, keep pressed the locking position lever. -
Page 15: Assembly Of The Visor On The Column
ASSEMBLY 5 – ASSEMBLY OF THE VISOR ON THE COLUMN The visor has been calibrated during testing procedures, therefore it is not necessary to recalibrate it when it has to be assembled. • Insert the fixing screw, the spring and the washers into the column as indicated in the picture aside. -
Page 16: Preparation
PREPARATION PREAPARATION OF THE VEHICLE Make sure the headlights are clean and dry. If the vehicle is equipped with a headlight aligner, set in on “0”. Eliminate anything that could affect the correct position of the vehicle: mud, snow, ice, etc. -
Page 17: Alignment With The Vehicle
ALIGNMENT WITH THE VEHICLE POSITIONING Place the headlight tester in front of the right headlight of the vehicle at a distance of about 20 cm, measure the height from the floor at the center of the headlight and adjust the optical chamber at the corresponding height using the graduated scale on the column. -
Page 18: Alignment With Mirror Visor
ALIGNMENT WITH THE VEHICLE ALIGNMENT WITH MIRROR VISOR Locate two details on the front of the vehicle that are perfectly symmetrical between them (for example the top of the windshield or the headlights themselves). Turn the optical chamber until, when you look in the mirror, the two reference points meet the black line stenciled on the mirror. -
Page 19: Headlight Test
HEADLIGHT TEST ADJUSTMENT Inside the motor compartment, read at the top of the headlight the tilt indicated by the manufacturer, e.g. 1.2%, and turn the knob on the rear part of the optical box as indicated. If there is no indication by the manufacturer, comply with the laws in force in your country. -
Page 20: Fog Light Test
HEADLIGHT TEST FOG LIGHT TEST If present, displace and centre the headlight tester on the the fog beam projector. On the the headlight tester turn the knob on the rear part of the optical box according to the manufacturer indications. If there is no indication by the manufacturer, comply with the laws in force in your country. -
Page 21: Supplementary Instructions
SUPPLEMENTARY INSTRUCTIONS REPLACEMENT OF LASER VISOR BATTERIES Unscrew the two screws on the cover of the laser visor and replace the 3 penlight batteries size AA 1.5V, respecting the correct polarity, close the visor and fasten the cover with the screws provided. BATTERIES REPLACEMENT –... -
Page 22: Warranty
WARRANTY At the time of delivery it is essential to check at once and make sure you have received all the material indicated in the shipping documents, and that the machine has not undergone damage during shipment. In this case, show the damage to the forwarder and inform our customer service department.
Need help?
Do you have a question about the 12066 and is the answer not in the manual?
Questions and answers
Price of device