Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MSI BT2RM
Summary of Contents for MSI BT2RM
- Page 1 (MS-6837D) Bluetooth 2.0+EDR USB Module User’s Guide...
- Page 2 FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
-
Page 3: End Product Labeling
End Product Labeling This transmitter module is authorized only for use in device where antenna may be installed such that 20 cm may be maintained between antenna and users (for example access points, routers, wireless ADSL and similar equipment). The final end product must be labeled in a area with the following: “Contains TX FCC ID: I4L-MS6837D ”. -
Page 4: Bluetooth Module
>>> 1.1 BT2RM (MS-6837D) Bluetooth Module MSI Bluetooth 2.0+EDR USB module, BT2RM, is a USB 1.1 Full Speed Module compatible with USB 2.0, being used to integrate with systems such as notebook, Barebone computer, PDA, portable PC, Smart Phone. With MSI... - Page 5 >>> 1.2 BT2RM Works 1.2.1 In Bluetooth Connection The term “Bluetooth” refers to a worldwide standard for the wireless exchange of data between two devices. In order to ex- change data, two Bluetooth devices must establish a connection. Before a connection is established, one device must request a connection with another.
-
Page 6: Bluetooth Specifications
>>> 1.3 Specifications Bluetooth Specifications Radio Standard Bluetooth Class II v2.0+EDR Frequency Band 2.400-2.4835 GHz Data Rate Up to 2169kbps Channel 79 sub-channels Transmission FHSS (Frequency Hopping Spread Spectrum) Modulation GFSK@1Mbps, π/4 DQPSK@2Mbps, 8DPSK@3Mbps Antenna Type Printed Circuit Antenna or One antenna connector support Temperature... - Page 7 Link Manager 3-slot Packets 5-slot Packets Slot Offset Timing Accuracy Switch Hold Mode Sniff Mode Test Mode Park Mode RSSI Power Control Authentication Encryption System Support Windows® 2000/ME/98SE/XP Generic Access Profile/Service Discovery Profile/Serial Port Profile/Dial-Up Networking Profile/Fax Profile/LAN Access Profile/Generic Object Exchange Profile/File Transfer Profile/Object Push Profile/Synchronization Profile Support...
-
Page 8: System Requirements
>>> 1.4 System Requirements Before installing BT2RM, your PC should meet the following items: - One desktop/notebook PC with an available MiniPCI slot. - Windows 98SE/ME/2000/XP operating system. ® - Minimum 5MB free disk space for installing the driver and utilities. -
Page 9: Product View
>>> 1.6 Product View Bluetooth antenna Connector USB Connector C o n n e c t y o u r notebook using the provided USB cable. -
Page 10: Hardware Installation
Hardware Installation The following diagrams provide you a basic installation for your BT2RM The instruction below is suitable for most com- puters with USB slot. For more information about the USB module, please refer to your computer’s manual. BT2RM Installing... -
Page 11: Software Installation
Setup CD to copy files during the installation. Please NOTE that the BT2RM should be installed into your computer before installing the driver and utility. Then, the operating system will detect a new device and start Click Cancel here to start to con- figure the new device. - Page 12 Insert the software CD into your CD-ROM drive, and the Setup ST EP program should launch automatically. If the Autorun program doesn’t launch automatically, click Start E:\setup.exe at the taskbar and select Run..Type (where is your CD-drive) in the Open box and click OK to launch the Setup program manually.
- Page 13 Click the Exit button. ST EP The Wireless LAN icon and Bluetooth icon will appear in the status bar. Bluetooth icon...
- Page 14 FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Need help?
Do you have a question about the BT2RM and is the answer not in the manual?
Questions and answers