Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for IndigoVision 3000 Series
Summary of Contents for IndigoVision 3000 Series
- Page 1 Compact Network Video Recorder - Alarm Server 3000 Series Hardware Guide...
- Page 2 AS AVAILABLE BASIS LEASE CONTACT NDIGO ISION IMITED EITHER BY POST OR BY E MAIL AT PARTNER SUPPORT INDIGOVISION WITH ANY SUGGESTED CORRECTIONS AND OR IMPROVEMENTS TO THIS MANUAL AVE AS OTHERWISE AGREED WITH NDIGO ISION IMITED AND NDIGO ISION...
-
Page 3: Table Of Contents
ABLE OF ONTENTS ........5 BOUT UIDE Safety Notices ............5 ........7 ONFIGURATION Overview ..............7 Important Safeguards ..........8 NVR-AS Power Up Sequence ......8 NVR-AS Power Off Sequence ......9 NVR-AS Usage ............9 Configuration ............. 11 Using the Web Configuration Pages .... - Page 4 ......31 ARDWARE PECIFICATION Video ................. 31 Audio ................. 31 Storage ..............31 Network Connections ..........32 Performance .............. 32 NVR-AS Metrics ............32 Removable Disk Metrics ..........33 Environment .............. 33 Regulatory ..............33 A GNU G ....35 ENERAL UBLIC ICENCE...
-
Page 5: About This Guide
BOUT UIDE This guide is written for users of the Compact Network Video Recorder - Alarm Server 3000 Series. It provides introductory information about the products, and a description of their hardware and specifications. For information on how to use the Web Configuration pages to configure the units, see the Web Configuration Guide. -
Page 7: Configuration
IndigoVision 10000 (HD) units configured as transmitters; this can be on-demand, time scheduled, or event driven • Play back video and audio streams to IndigoVision 8000 (MPEG4) units, IndigoVision 9000 (H.264) units, and IndigoVision 10000 (HD) units configured as receivers, or compatible PC software clients •... -
Page 8: Important Safeguards
Important Safeguards • You must read all the safety and operating instructions before using the product. • You should adhere to all warnings on the product and in the operating instructions • Holes in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from overheating. -
Page 9: Nvr-As Power Off Sequence
NVR-AS Power Off Sequence 1 To disconnect the device, press the Suspend/Resume button on the front, or click the Shutdown button on the Diagnostics web page. 2 Wait for both the CPU and Alarm LEDs on the front panel to change from solid on, to flashing. - Page 10 • Removing evidence of an incident You may need to remove a disk containing footage of an incident that has occurred for evidential purposes, and replace it to continue normal recording. Before removing the disk, you should ensure that all recordings on the disk are protected (see “Protecting Recordings”...
-
Page 11: Configuration
Configuration You can configure your NVR-AS using the Web Configuration pages or a serial connection. Default IP Properties The NVR-AS devices are programmed with the default IP properties listed in step Table 1. Table 1 Default IP Properties Initial Configuration IP Address 10.5.1.10 Subnet Mask... - Page 12 Step 1: Preparing an Isolated Network Connect your NVR-AS and the PC you are using to configure it on their own isolated network. To do this, connect the unit to the PC using an Ethernet crossover cable (see Figure 1.) You can use either the Port 1 or Port 2 Ethernet interface for the connection.
- Page 13 Step 2: Preparing PC for Initial Device Configuration Each NVR-AS is supplied with the data IP address set to 10.5.1.10 and the subnet mask set to 255.0.0.0. You cannot connect the devices to your network until you have changed these settings to suit your network. To change the default IP addresses of the NVR-AS, you must first (temporarily) modify your PC’s network settings.
- Page 14 3 Right-click Internet Protocol (TCP/IP) and select Properties. Figure 4 Internet Protocol Properties dialog 4 Set the IP address to an address close to the factory IP address, for example, 10.5.1.2 and change the PC’s subnet mask to 255.0.0.0 (the same as the factory default). 5 Click OK, then OK again.
- Page 15 3 The Web Configuration Home page opens. Figure 5 Web Configuration Home page 4 Click the Network in the menu on the left of the web page. Figure 6 Web Configuration Network page...
- Page 16 5 Configure the device as required using the following fields: • Host Name — Enter a name for the NVR-AS. • Location — Enter a location to identify the device. • IP Address — Enter the device’s IP address. • Subnet Mask —...
- Page 17 • Recording Stream — Select the stream you want to use for recording. This is then used for all recording jobs on this NVR-AS. When you have configured the device as required, click Submit to apply the changes to the device. You are now ready to take the device off the isolated network and connect it to the main network.
-
Page 18: Using The Serial Port Connection
Using the Serial Port Connection To configure your NVR-AS using the serial port, you require an RS232 serial cable. 1 Connect the serial cable between the NVR-AS and the PC as shown in Figure 7. Console Port NVR-AS Serial cable Figure 7 Serial port connection 2 On the PC, use a Terminal Emulation program such as Windows HyperTerminal and set the serial port parameters... - Page 19 The following settings are available: • IP Address — Enter the device’s IP address • Subnet Mask — Enter the device’s IP network subnet mask. • Gateway — Enter the appropriate default gateway for remote network access: this is only required if the devices are to be accessed from a different subnet.
-
Page 20: Attaching The Device To The Network
Attaching the Device to the Network After configuring the IP settings, connect it to the network. 1 Reconnect your PC to the network. 2 Use a standard RJ45 connector and CAT5 cable to connect to the ports on the rear of the device, as shown in Figure 8. Console Port NVR-AS Power Supply... -
Page 21: Hardware Description
ARDWARE ESCRIPTION This chapter describes the hardware for the NVR-AS units and the removable disk. Warning: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages. Refer all service to qualified service personnel. -
Page 22: Nvr-As Rear View
The LEDs on the NVR-AS report activity and status. Table 2 Chassis LED description Name Status Meaning Solid off Normal operation Solid on CPU processing is too high NVR-AS CPU + Alarm Flashing suspended Activity (server Flashing Normal operation status) Solid on/off Server failure Link Port 1 /... -
Page 23: Port 1 / Port 2 Network Connector
At the rear of the unit, there are ports to connect to the following: • Power • Port 1 network connector • Port 2 network connector • Serial RS-232 console port Port 1 / Port 2 Network Connector These port network connectors are RJ-45 connectors. These interfaces can be set to use fixed 100Mbps Half Duplex, 100Mbps Full Duplex, 1Gbps Full Duplex link, or can be set to auto-negotiate. -
Page 24: Power
Power The power inlet is a keyed two-pin interface which mates with the power supply unit supplied. Removable Disk Hardware The NVR-AS uses a 3.5“ SATA disk in a removable drive enclosure. Caution: If you start the NVR-AS with no disk, the NVR-AS will start in the suspended state (CPU and Alarm LEDs flashing). -
Page 25: Using The Removable Disk
Disks are not field replaceable. Faulty disks must be returned to IndigoVision as part of a caddy assembly. Individual disk and caddy assemblies required as spares or replacements can be ordered from IndigoVision. - Page 26 To replace the disk: 1 Press the Suspend/Resume button, or click the Shutdown button in the Diagnostics web page once to suspend the NVR-AS. The CPU and alarm LEDs both light solid red to indicate that the device is suspending. Once it is suspended, the CPU and alarm LEDs both flash together.
-
Page 27: Protecting Recordings
6 Press the Suspend/Resume button once to resume operation. The CPU LED stops flashing and goes out, but the alarm LED continues to flash. When the alarm LED stops flashing, the unit has resumed operation. Table 4 LED sequence Action Activity Meaning NVR-AS... - Page 28 2 Click Disk from the options on the left. The Disk Configuration page opens. Figure 14 Disk Configuration page 3 Click Protect All to protect all recordings and events on the current disk. Click Unprotect All to allow all recordings and events to be deleted.
-
Page 29: Playing Back Recordings From An Archive Disk
Playing Back Recordings from an Archive Disk You may need to review old recordings stored on an archive disk. Warning: If you are using a single NVR-AS to record footage and to play back archived data, you must ensure that there are no active recording jobs or event filters on the NVR-AS and that time-based deletion of recordings (time and space reaping) is disabled (that... -
Page 30: Troubleshooting
Troubleshooting The following section describes actions that may be necessary when troubleshooting. Checking a Disk To check the integrity of the file structure contained on the current disk: 1 Open a DOS prompt. 2 Type telnet IP address 3 Log in as root, with password admin. (If you have set a password to allow web access, use this instead of admin.) 4 Type diskcheck. -
Page 31: Hardware Specification
• Recording and playback of High Definition (HD) streams from IndigoVision 10000 transmitters and receivers. • Recording and playback of H.264 streams from IndigoVision 9000 transmitters and receivers. • Recording and playback of MPEG4 Simple Profile streams from IndigoVision 8000 transmitters and receivers. -
Page 32: Network Connections
Network Connections • IEEE 802.3 and IETF standards: • 10/100/1000 Base-T Ethernet, TCP, UDP, ICMP and IGMP • Physical connection via RJ-45 Performance Feature Maximum Recording Streams Recording Bandwidth 40 Mbps Configured Recording Jobs Total Number of Recordings 40,000 Number of Alarms 100,000 Playback Streams Playback Bandwidth... -
Page 33: Removable Disk Metrics
Power • Mains power supply unit operating voltages: • Input: 100-240V ~ 47-63Hz 1.8A • Output: 12Vdc 5A • Power consumption: 32VA max Removable Disk Metrics Dimensions • 102mm x 147mm x 26.1mm Weight • 1TB - 0.665Kg • 500GB - 0.53Kg Environment •... -
Page 35: A Gnu General Public Licence
ENERAL UBLIC ICENCE IndigoVision's NVR-AS products use code that is freely available under the GNU General Public Licence (GPL). This licence makes it a requirement to release changes made to the source code. In compliance, the GPL source code and any changes made by Indigovision are available on request through IndigoVision Customer Support. -
Page 37: Index
NDEX protecting recordings 27 removing 26 archived disks 29 SATA 24 archiving disks 9 attaching NVR-AS to network 20 audio specification 31 environmental specification 33 changing disks 25 changing PC settings 13 formatting disks 30 checking disks 30 front view 21 configuration prerequisites 11 using serial port 18... - Page 38 removing disk 26 network evidence of incident 10 connections 32 reusing same disk 9 ports 23 NVR-AS attaching to network 20 configuration 14 SATA disks 24 configuration, advanced 20 serial RS-232 console port 23 disconnecting 21 specifications front view 21 audio 31 hardware 21 environmental 33...
- Page 40 Document ID: IU-NVR-COM-MAN001-4...