Advertisement
1.4.
GENERAL SAFETY INSTRUCTIONS
Familiarise yourself with the application and limitations of the charger as well as the potential hazards. Also refer to the vehicle
9
manufacturer's hand book. If IN ANY dOUBT CONSULT A QUALIfIEd ELECTRICIAN.
Ensure the charger is in good order and condition before use. If in any doubt do not use the unit, contact your Sealey stockist.
9
Use the starter/charger in the upright position only and ensure it is placed on a stable surface which will adequately support its weight.
9
Ensure the charger is disconnected from the mains supply before attaching/detaching the power clamps to/from the battery.
9
Keep tools and other items away from the engine and ensure you can see the battery and working parts of engine clearly.
9
Ensure the output of the charger is the same voltage as the battery.
9
Ensure that during charging, the charger is placed in a location where there is sufficient ventilation to prevent the build up of explosive
9
gases from a lead acid battery, and DO NOT cover or obstruct the charger ventilation louvres.
If battery has caps to access the battery fluid, remove the caps and check the fluid level before connecting the power clamps.
9
If necessary top-up the battery with distilled water by referring to the battery manufacturer's instructions (Apply the personal safety
9
precautions described in part 1.3).
If the charger receives a sharp knock or blow the unit must be checked by a qualified service agent before using.
9
If the battery terminals are corroded or dirty clean them before attaching the power clamps.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT dis-assemble the charger for any reason. The charger must only be checked by qualified service personnel.
8
DO NOT try to charge a non-rechargeable battery.
8
DO NOT try to charge battery if battery fluid is frozen.
8
WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area, or allow
‰
them to touch the battery terminals.
DO NOT allow power clamps to touch each other or to make contact with any metallic part of the vehicle.
8
DO NOT cross connect power leads from charger to battery. Ensure positive (+/REd) is to positive and negative (-/BLACK) is to negative.
8
DO NOT pull the cables or clamps from the battery terminals.
8
DO NOT use the charger outdoors, or in damp, or wet locations and DO NOT operate within the vicinity of flammable liquids or gases.
8
DO NOT use charger inside vehicle or inside engine compartment.
8
Ensure there is effective ventilation to prevent a build-up of explosive gases, and do not cover or obstruct charger ventilation louvres.
9
DO NOT use the charger for a task for which it is not designed.
8
WARNING! DO NOT simultaneously charge batteries of different capacities or discharge levels.
‰
WARNING! If a fuse blows, ensure it is replaced with an identical fuse type and rating. Use only Sealey genuine parts.
‰
When not in use, store the charger carefully in a safe, dry, childproof location.
9
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
2. INTRODUCTION
Steel case with a sturdy carry handle, these single phase chargers feature good ventilation to maintain low transfer temperatures. A large
ammeter displays rate of charge and a dash mounted fuse provides polarity protection in the event of the clips being connected incorrectly.
Rocker switches control variable output to the battery to maintain peak condition. Suitable for regular and low maintenance batteries.
3. SPECIFICATION
model no.
CHARGE106
Output
12/24V
Output charge peak
8A(6A)
(EN)
Battery range
10-95Ah
Charging rates
2
Supply
230V
Polarity protection
Fuse (1 x 15A)
Fuse
SBf1550 (pack
of 50)
CHARGE106.07
(single)
4. OPERATION
WARNING! Ensure all the safety instructions in section 1 are read and followed before using the charger.
‰
4.1.
PREPARATION
4.1.1.
It is important to correctly prepare for charging, ensuring that you follow Section 1 safety requirements carefully.
4.1.2.
Check that the capacity of the battery is compatible with charger output.
4.1.3.
Charging current (amps) should not exceed one tenth of the value of the battery capacity (amp hours).
4.1.4.
Check battery to ensure that the POSITIVE and NEGATIVE terminals are clearly identifiable before removing the battery from the
vehicle.
4.1.5.
Follow the vehicle manufacturer's instructions for charging the battery. Disconnect and remove the battery from the vehicle and place
in an appropriate safe area ready for charging.
4.1.6.
Remove the battery electrolyte cover or caps to allow the gases produced by charging to escape.
4.1.7.
Check that the electrolyte fluid level in the battery is above the plates. If not, add distilled water to cover them by 5-10mm.
DO NOT touch the battery fluid as it is corrosive.
8
© Jack Sealey Limited
CHARGE107
CHARGE110
12/24V
12/24V
11A(7A)
14A(10A)
20-105Ah
20-120Ah
2
2
230V
230V
Fuse (1 x 15A)
Fuse (1 x 20A)
SBf1550
SBf2050 (pack
(pack of 50),
of 50)
CHARGE107.07
CHARGE110.07
(single)
(single)
Original Language Version
CHARGE112
12/24V
16A(12A)
20-180Ah
2
230V
Fuse (1 x 30A)
mF3010
(pack of 10),
CHARGE112.07
(single)
CHARGE106.V3, 107.V3, 110.V3, 112.V3, 115.V3, 124.V3 | Issue:1 10/11/17
CHARGE115
CHARGE124
12/24V
12/24V
19A(15A)
28A(24A)
20-250Ah
25-320Ah
2
2
230V
230V
Fuse (1 x 30A)
Fuse (1 x 40A)
mF3010
mF4010 (pack
(pack of 10),
of 10),
CHARGE115.07
CHARGE124.07
(single)
(single)
Advertisement
