Nailer Safety Warnings - Ryobi P318 Operator's Manual

GENERAL POWER TOOL SAFETY WARNINGS
 Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
 Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
BATTERY TOOL USE AND CARE
 Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
 Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
 When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
 Always assume that the tool contains nails. Careless
handling of the nailer can result in unexpected firing of
nails and personal injury.
 Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the nail
causing an injury.
 Do not actuate the tool unless the tool is placed firmly
against the workpiece. If the tool is not in contact with
the workpiece, the nail may be deflected away from your
target.
 Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the tacker may be accidentally activated if it is
plugged in.
 Use caution while removing a jammed nail. The mecha-
nism may be under compression and the nail may be
forcefully discharged while attempting to free a jammed
condition.
 Do not use this nailer for fastening electrical cables.
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.

NAILER SAFETY WARNINGS

3 — English
 Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
 Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion, or risk
of injury.
 Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 265°F may cause explosion.
 Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage
the battery and increase the risk of fire.
SERVICE
 Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
 Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
 Hold power tool by insulated gripping surfaces, when
performing an operation where the nail may contact
hidden wiring. Nails contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
 Know your power tool. Read operator's manual care-
fully. Learn its applications and limitations, as well as
the specific potential hazards related to this power
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
 Always wear eye protection with side shields marked
to comply with ANSI Z87.1. Everyday glasses have only
impact resistant lenses. They are not safety glasses. Fol-
lowing this rule will reduce the risk of serious personal
injury.
 Eye protection which conforms to ANSI specifications
and provides protection against flying particles both
from the FRONT and SIDE should ALWAYS be worn
by the operator and others in the work area when
loading, operating or servicing this tool. Eye protection
is required to guard against flying fasteners and debris,
which could cause severe eye injury.