Page 1
Please use this service manual with referring to the 修理の際は、必ず取扱説明書を参照の上、作業を行っ ● operating instructions without fail. てください。 ● Some illustrations using in this service manual are 本文中に使用しているイラストは、説明の都合上現物 ● slightly different from the actual set. と多少異なる場合があります。 Denon Brand Company, D&M Holdings lnc. X0385 V.04 DE/CDM 0810...
イヤーの整形をおこなってください。正しく整形されてい they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise ないとノイズ発生の原因となることがあります。 generation. 上面からみたワイヤー整形 Wire arrangement viewed from the top Back Panel side Front Panel side RCD-CX1...
"EEP Err2" : Amp-related checksum error "EEP Err2":Amp 関連チェックサムエラー "EEP Err3" : Last Line1,2 select checksum error "EEP Err3":最終 Line1,2 select チェックサムエラー b2 Communication result with B/E b2 B/E との通信結果 "BE OK" : normal "BE OK":正常 "BE Err" : Communication error "BE Err":通信不可 RCD-CX1...
Page 7
5.SACD MECHA ASSY" and "EXPLODED VIEW" SACD MECHA UNIT (Ref. No. of EXPLODED VIEW : 2-3) MAIN UNIT SUB ASSY Refer to "DISASSEMBLY 6.MAIN UNIT SUB ASSY" and "EXPLODED VIEW" MAIN UNIT SUB ASSY (Ref. No. of EXPLODED VIEW : 2-2) RCD-CX1...
Page 8
Picture A Front side The viewpoint of each photograph (photography direction) 各図の視点(撮影方向) Top view Picture C Picture D Picture B RCD-CX1...
(2) Disconnect the connector wire and FFC cable.(コネクタワイヤーと FFC ケーブルをはずす。 ) CY051 FFC CABLE Picture A Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in FRONT PANEL SUB ASSY. FRONT PANEL SUB ASSY の各基板のはずしかたは "EXPLODED VIEW" を参照してください。 RCD-CX1...
Page 10
→ SW POWER UNIT → SHIELD BRACKET → (1) Remove the screws. ( ねじをはずす。) TOP ANGLE Picture C (2) Disconnect the connector wires and boards.(コネクタワイヤーとコネクタボードをはずす。 ) CW021 CW021 Top view CW021 CW021 (3) Remove the screws.(ねじをはずす。 ) Top view RCD-CX1...
Proceeding ( 手順 ) : TOP PANEL SIDE PANEL → → TOP ANGLE → SW POWER UNIT → SHIELD BRACKET BACK PANEL ASSY → (1) Disconnect the connector wire.(コネクタワイヤーをはずす。 ) CORD HOLDER : Loose Top view CX022 CX023 FFC CABLE RCD-CX1...
Page 12
(2) Remove the screws.(ねじをはずす。 ) Picture B (3) Disconnect the connector wire.(コネクタワイヤーをはずす。 ) CW021 Top view Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in BACK PANEL ASSY. BACK PANEL ASSY の各基板のはずしかたは "EXPLODED VIEW" を参照してください。 RCD-CX1...
Page 13
FRONT PANEL SUB ASSY TOP PANEL BRACKET → → FRONT ANGLE → (1) Remove the screws. ( ねじをはずす。 ) Bottom view Top view (2) Disconnect the connector wire and FFC cable.(コネクタワイヤーと FFC ケーブルをはずす。 ) FFC CABLE CY051 Top view RCD-CX1...
Page 14
SW POWER UNIT → SHIELD BRACKET → FRONT PANEL SUB ASSY TOP PANEL BRACKET → → FRONT ANGLE SACD MECHA ASSY → → (1) Disconnect the connector wires. ( コネクタワイヤーをはずす。) FFC CABLE CY091 Top view CORD HOLDER : Loose RCD-CX1...
Page 15
FRONT PANEL SUB ASSY → TOP ANGLE BRACKET → FRONT ANGLE → SACD MECHA ASSY → MAIN UNIT SUB ASSY Please refer to "EXPLODED VIEW" for the disassembly method of MAIN UNIT SUB ASSY. MAIN UNIT SUB ASSY のはずしかたは "EXPLODED VIEW" を参照してください。 RCD-CX1...
Page 16
• Remove the 8U-210025 SW power unit and shield ・ 8U-210025 SW POWER UNIT、 SHIELD BRACKET を外す。 bracket. • Remove the four screws fixing the mechanism in place. ・ メカを固定しているネジ4本を外す。 メカ Mechanism 左の隙間 上の隙間 Ajusting the left gaps Ajusting the top gaps 下の隙間 右の隙間 RCD-CX1...
Page 17
Mount the 8U-210025 SW power unit and shield bracket. ください。 3. 最終確認 3. Final check 作業終了後、電源を ON にし TRAY の OPEN/CLOTH を1回 After completing the operations, turn on the power and open おこない、隙間の確認をおこなってください。 and close the tray once to check the gap. RCD-CX1...
Laser drive current (Iop) check HF 波形の確認(WAVE FORMS 参照) HF wave form check (Refer to WAVE FORMS) 現在値が初期値の Present value exceeds the ini- 1.5 倍になっている tial value by 1.5 times トラバースユニット交換 Traverse Unit replacing 交換後にレーザー電流値の記憶 Laser current (Iop) memorizing after replacement RCD-CX1...
Page 19
ニット ) の交換 (Traverse Unit) Iop( レーザー駆動電流)をチェックします。 Check the Iop (Laser drive current) 現在の Iop 値が初期値の 150%を越えている場合、トラ If the present Iop (current) value exceeds.+150% of the バースユニット(レーザーピックアップ)を交換してく initial value, replace the Traverse unit (Laser Pick-up) with ださい。 a new one. RCD-CX1...
Page 20
FL Display (The display part of 8 digits) T 2 ― ― 2 5 ボタンを押すと、"T21" 現在値を保存せず、 T 2 ― ― "T22" 現在値の表示へ戻ります。 2 5 button to display the current value “T22” (5) Press the without storing the current value “T21”. RCD-CX1...
Page 21
"nnnnn" is displayed as 0 so you can check. FL 管の表示 (8 桁の表示部 ) FL Display (The display part of 8 digits) T T ( −:消灯、Y:1: CD, 2: DVD、nnnnn:時間 [h]) ( − : Off, Y:1: CD, 2: DVD, nnnnn: Hour [h]) RCD-CX1...
Spring at this time. (Spring may be warped) SLIDE CAM side (3) トレイ左側に設けられた孔より、メカフレームの突起 (3) Check that the projection of Mecha Frame becomes po- 部が写真に示す位置になっていることを確認します。 sition of the photograph, from the hole at the left on the Tray. RCD-CX1...
Page 28
す。 under selection is performed from the beginning. (If the button is pushed, the address corresponding to the chosen mode 選択モードを変更せずに ボタンを押した場合も、選択中のモードを最初から実行します。 will be searched again.) The pause mode is set after tracing is completed. ボタンを押したら、選択しているモードに対応したアドレスを再度サーチします。) トレース終了時は、PAUSE 状態になります。 RCD-CX1...
Page 29
7th place : During ZZ selection, " * " displayed at 7th place. 7 桁目 : ZZ 選択中の場合、" * " を表示します。 When both Y and ZZ are set, " * " displayed at 4th and 7th places. Y と ZZ の両方確定時は、4 桁目と 7 桁目に " * " を表示しまする。 RCD-CX1...
Page 30
SDRAM for CPU's working error SDRAMERR SDRAMERR : SDRAM エラー SDRAM error DAC ERR DAC ERR : DAC1796 との通信エラー Communication error between DAC1796 2753 ERR 2753 ERR : CXD2753 との通信エラー Communication error between CXD2753 SUB ERR Communication error between sub microprocessor SUB ERR : サブマイコンとの通信エラー RCD-CX1...
Page 31
OPEN 表示 (It readjusts with heat run mode.) ↓ CLOSE 表示 OPEN display ↓ ↓ READING 表示 CLOSE display ↓ ↓ READING display FL 管の表示 (8 桁の表示部 ) ↓ FL Display (The display part of 8 digits) T T RCD-CX1...
Page 32
L0 層 TE 信号の AGC 値 (0x100 で 1 倍、0x200 で 2 倍。 Y/0x100 の比率計算) teagc0 L0 layer TE signal AGC value (1x for 0x100, 2x for 0x200. Y/0x100 ratio calculation.) TE の振幅が目標ターゲット 2.45V になる様に調整される。 Adjusted so that TE amplitude reaches target of 2.45V. RCD-CX1...
Page 33
L1 層 AS 信号の AGC 値 (0x100 で 1 倍、0x200 で 2 倍。 Y/0x100 の比率計算) asagc1 L1 layer AS signal AGC value (1x for 0x100, 2x for 0x200. Y/0x100 ratio calculation.) AS の振幅が目標ターゲット 2.45V になる様調整される。 Adjusted so that AS amplitude reaches target of 2.45V. RCD-CX1...
Page 34
HYBR DVD-VR DVvr SACD(Hybrid) HYBR DVD-VR DVvr Unknown NONE Mixed mode CD-ROM CDRD 不明 NONE Mixed mode CD-ROM CDRD SACD SACD SACD SACD (When there are multiple formats, the format played and identified with priority is displayed.) ( フォーマットが混在する場合、優先して再生、認識されるフォーマットを表示します。) RCD-CX1...
Page 35
DVD 1 層ディスクの場合、無効。 A display of PI uncorrectable number of the outer circumference of In the case of 1-layer DVD disc, it is invalid. CD 時は C2 訂正不可数。(x6) 2-layer and an address. CD : C2 uncorrectable error number (x6) RCD-CX1...
Page 45
Port P12 Port P13 (Note 3) (Note 3) (Note 3) (Note 3) Note 1: ROM size depends on microcomputer type. Note 2: RAM size depends on microcomputer type. Note 3: Ports P11 to P14 exist only in 128-pin version. RCD-CX1...
Page 46
P3_3/A11 MODEL_ID2 MODEL ID SETTING(2) P3_2/A10 DV_STB ON/STB OK from DV3.2 P3_1/A9 TU_POWER Tuner power control VCC2 P3_0/A8(/-/D7) FL_CS FLD CHIP SELECT P2_7/AN2_7/A7(/D7/D6) TU_DATA_OUT From tuner pack data P2_6/AN2_6/A6(/D6/D5) TU_CLK TUNER PACK SIRIAL CLOCK P2_5/AN2_5/A5(/D5/D4) TUNED For tuner pack RCD-CX1...
Page 47
(For bandwidth identification only for JP model Wide"L":To the TV band, Narrow"H":TV band none) P10_2/AN2 RDS presence switch P10_1/AN1 BE_PWR_MONI BACKEND POWER watch AVSS P10_0/AN0 MODEL_ID1 MODEL ID setting(1) VREF AVCC P9_7/*ADTRG/SIN4 RESERVED P9_6/ANEX1/SOUT4 FL_DA FL DATA OUT 100 P9_5/ANEX0/CLK4 FL_CLK FL CLICK OUT * = Negative logic RCD-CX1...
Page 49
PWM output of channel 2. PWMFB2 Feedback for inner loop of channel 2. For estimating the power dissipation in the zobel resister, this input is sensing the zobel voltage via a resistive network of channel 2. Feedback for global loop of channel 2. RCD-CX1...
Page 50
I nB1 BLOCK DIAGRAM Ach Tone Filter V+ GND V- Bias Control Logic In A1 In A2 Zero Cross Detection In A3 In A4 Out A TONE In B1 In B2 In B3 OutB TONE In B4 Bch Tone Filter RCD-CX1...
Indicates number of zeros after effective number. 2-digit effective number. Units: pF. 220pF (0 or 1) Indicates number of zeros after effective number. 2-digit effective number. Units: pF. When the dielectric strength is indicated in AC, "AC" is included after the dieelectric strength value. RCD-CX1...
EXPLODED VIEW WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。 RCD-CX1...
Page 81
EXPLODED VIEW OF SACD MECHANISM WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。 RCD-CX1...
CAM SPRING attachment area (0.9mg) Both ends side of boss contact area under BECA BASE-SLIDE CAM. (7.0mg each x 2) Grease : EM30L Only shaft area of gear axis (2.0mg each x 2) TRAY bottom MECHA BASE Greasing positions MECHA BASE bottom RCD-CX1...
Page 83
DAMPER 00D4210846005 O RING 00D4630976306 BOSS SPRING 2x3CBS-B 2x4CBS-B 2x6CFS-B 0RD4713003002 2.6x3CBS-B 2.6x5CFS-B 3x5CBS-B 2.6x5CBTS(S)-Z 00D4751190016 SLIT WASHER 1.7x3.2x0.5 00D4751157091 SLIT WASHER 3.1x5.4x0.5 00D4751190003 SLIT WASHER 3.1x12.0x0.5 00D4751161016 POLY WASHER 4.1x6.5x0.5 0RD4761003009 3E RING 2x6CBTS(P)-Z 00D9KC1H011 SCR-DAMPER 00D9KC2G083 DAMPER-IDLE RCD-CX1...
INST. MANUAL (E2) 541110058001D INST. MANUAL (E3) 00D5150918607 SERVICE STATION LIST S.S.LIST (EX) E2,E3 307010020009D RC-1109 BATTERY(R03X2) 00D2062150103 AC CORD WITH CONN. 00D2062215006 AC CORD-E1/10A/INLET 00D2062219002 AC CORD SET (E3) 00D2310089007 AM LOOP ANTENNA 00D3950028003 FM ANT ASS Y(F/WELT) JP,E3 RCD-CX1...
Page 86
Ref. No. Part No. Part Name Remarks Q'ty 00D3950026005 FM ANT. WIRE WARRANTY (HOME) GUARANTEE CARD (M) 998545000110D POS LABEL E2 POS LABEL UPC LABEL CONT.CARD(L)SUB ASSY E2,E3 00D5139111030 COLOR LABEL E2,E3 RCD-CX1...
さい。 8U-310008 DRIVE/SACD/DAC P.W.B. Unit : Component Side * Reference voltage of ⑬ , ⑯ ~ is GND_D1 ⑮ , and reference voltage of other point is VC16 ⑭ . *⑬、⑯∼ の基準電圧は GND_D1 ⑮で、他のポイントの基準電圧は VC16 ⑭です。 RCD-CX1...
NOTICE: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. RCD-CX1...
Page 93
SCHEMATIC DIAGRAMS (1/24) 8U-310008 DRIVE/SACD/DAC UNIT (1/3) RCD-CX1...
Page 94
SCHEMATIC DIAGRAMS (2/24) 8U-310008 DRIVE/SACD/DAC UNIT (2/3) RCD-CX1...
Page 95
SCHEMATIC DIAGRAMS (3/24) 8U-310008 DRIVE/SACD/DAC UNIT (3/3) RCD-CX1...
Page 96
SCHEMATIC DIAGRAMS (4/24) 8U-210024 SYS/DAMP/DISP UNIT (1/6) 8U-210024-2 DISP/KEY UNIT 8U-210024-3 VOL UNIT 8U-210024-4 P.SW/REMOTE UNIT 8U-210024-5 H/P UNIT for JP model RCD-CX1...
Page 97
8U-210024-2 SYS/DAMP/DISP UNIT (1/6) 8U-210024-2 DISP/KEY UNIT 8U-210024-3 VOL UNIT 8U-210024-4 P.SW/REMOTE UNIT 8U-210024-5 H/P UNIT for E3 model RCD-CX1...
Page 98
SCHEMATIC DIAGRAMS (6/24) 8U-210024-2 SYS/DAMP/DISP UNIT (1/6) 8U-210024-2 DISP/KEY UNIT 8U-210024-3 VOL UNIT 8U-210024-4 P.SW/REMOTE UNIT 8U-210024-5 H/P UNIT for E2 model RCD-CX1...
Page 99
SCHEMATIC DIAGRAMS (7/24) 8U-210024 SYS/DAMP/DISP UNIT (2/6) 8U-210024-1 M-COM BLOCK for JP model RCD-CX1...
Page 100
SCHEMATIC DIAGRAMS (8/24) 8U-210024 SYS/DAMP/DISP UNIT (2/6) 8U-210024-1 M-COM BLOCK for E3 model RCD-CX1...
Page 101
SCHEMATIC DIAGRAMS (9/24) 8U-210024 SYS/DAMP/DISP UNIT (2/6) 8U-210024-1 M-COM BLOCK for E2 model RCD-CX1...
Page 102
SCHEMATIC DIAGRAMS (10/24) 8U-210024 SYS/DAMP/DISP UNIT (3/6) 8U-210024-1 PHONO BLOCK for JP model RCD-CX1...
Page 109
SCHEMATIC DIAGRAMS (17/24) 8U-210024 SYS/DAMP/DISP UNIT (5/6) 8U-210024-1 DAMP.D/D CON. BLOCK for E3 model RCD-CX1...
Page 110
SCHEMATIC DIAGRAMS (18/24) 8U-210024 SYS/DAMP/DISP UNIT (5/6) 8U-210024-1 DAMP.D/D CON. BLOCK for E2 model RCD-CX1...
Page 111
SCHEMATIC DIAGRAMS (19/24) 8U-210024 SYS/DAMP/DISP UNIT (6/6) 8U-210024-6 SP TERMINAL UNIT 8U-210025 MONITOR UNIT for DV3.2 8U-210025-2 DV3.2 MONI JIG UNIT for JP model RCD-CX1...
Page 112
SCHEMATIC DIAGRAMS (20/24) 8U-210024 SYS/DAMP/DISP UNIT (6/6) 8U-210024-6 SP TERMINAL UNIT 8U-210025 DV3.2 MONITOR UNIT 8U-210025-2 DV3.2 MONI JIG UNIT for E3 model RCD-CX1...
Page 113
SCHEMATIC DIAGRAMS (21/24) 8U-210024 SYS/DAMP/DISP UNIT (6/6) 8U-210024-6 SP TERMINAL UNIT 8U-210025 MONITOR UNIT for DV3.2 8U-210025 DV3.2 MONI JIG UNIT for E2 model RCD-CX1...
Page 114
SCHEMATIC DIAGRAMS (22/24) 8U-210025 DV3.2 MONITOR UNIT for JP model RCD-CX1...
Page 115
SCHEMATIC DIAGRAMS (23/24) 8U-210025 DV3.2 MONITOR UNIT for E3 model RCD-CX1...
Page 116
SCHEMATIC DIAGRAMS (24/24) 8U-210025 DV3.2 MONITOR UNIT for E2 model RCD-CX1...