Advertisement
Quick Links
User Manual
Model HA2401-XI-325X
FCC ID: MYF-XI-325X
IC: 2837A- XI-325X
Interference Statement
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Warning: Changes or modifications not expressively approved by the party responsible
for compliance could void the user's authority to operate the equipment.
The term "IC:" before the radio certification number only signifies that Industry Canada
technical specifications were met.
NOTE: This system must be installed by experienced professional installers who are
familiar with radio frequency (RF) equipment operation as well as local building and
safety codes. Failure to do so may void the Product Warranty, as well as expose the end-
user to legal and/or financial liabilities.
Information to the user
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy. If not
installed and used in accordance with the instructions, it may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Advertisement
Related Manuals for HyperLink Technologies HA2401-XI-325X
Summary of Contents for HyperLink Technologies HA2401-XI-325X
- Page 1 User Manual Model HA2401-XI-325X FCC ID: MYF-XI-325X IC: 2837A- XI-325X Interference Statement This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 2 Any changes or modifications of equipment not expressly approved by the manufacturer could void the user’s authority to operate the equipment and the company’s warranty. NOTE: Certain high gain antennas are intended for point-to-point or point-to- multipoint applications only. These antennas are clearly identified in the table contained in this manual.
- Page 3 Failure to do so may void the Product Warranty, as well as expose the end-user to legal and/or financial liabilities. Hyperlink Technologies, its agents, resellers or distributors, are not liable for injury, damage, or violation of government regulations that may arise from failing to comply with the guidelines described in this document.
-
Page 4: Configuring The Wireless Router
Configuring the Wireless Router Connect to Unit with a cross-over cable to your PC or through a Switch (HUB) with straight cables. Apply power to the Router unit. Check the diagnostic lights to ensure proper connection. You should now be ready to configure the Router. Launch the Network Configurator Utility Click on File, Open Remote Config Click on Scan to locate the Device... - Page 5 Setting the Password The default password is “public”. Once you have accessed the security settings change the password. Click OK to accept changes. Select – This device is in my local subnet Click OK. Once the screen pops up that Configuration has been Read- Click OK...
- Page 6 Configure Router Parameters Click on Setup – General Setup or Click Setup Tab on the right of Window and General Setup For Basic Bridging, the default parameters should be OK: Enable Bridging, Enable Watchdog Reboot Timer (unit will reboot if there is not activity for long period of time) and MAC Authentication (security) Click on OK to accept these parameters.
- Page 7 Interface Setup Click on Setup – Interface Setup or the Tab on the right – Interface Setup. The Ethernet port by default is select as Remote and Enable. Click on Setup 2 (802.11b radio interface) Select the function of unit – One must be Base Station (does the polling) and second unit must be Satellite Station (responds to polling).
- Page 8 Click on Advanced, Select a network ID and the maximum modulation rate you want the radio to operate (higher speeds of 11 Mbps require better signal q uality.) Click on OK to accept changes Configure the Operating Frequency Click on Frequency, Select a Channel. Select an authorized frequency channel based upon the specific antenna used from the table in Appendix B.
- Page 9 Security Settings You could Click next on Security and select encryption at this time (Not required for basic configuration, implies 15-20% lower performance). Click on OK to accept changes and return to Main Menu. Click on Setup – System Access setup (or the Tab), select same Pass Phrase for all the units on your system.
- Page 10 Saving the Configuration Settings Please save your configuration changes, File , Save Config Accept Yes to Save to the Unit with the IP you have assigned, it would take few seconds and Unit will Reboot.
-
Page 13: Safety Notice
Installation Guide for this system. For further information contact: Hyperlink Technologies Technical Support Dept. 1201 Clint Moore Road Boca Raton, FL 33487 Email: support@hyperlinktech.com...
Need help?
Do you have a question about the HA2401-XI-325X and is the answer not in the manual?
Questions and answers