Related Manuals for Machfu MACH-3
Summary of Contents for Machfu MACH-3
- Page 1 Simplifying IoT from edge to enterprise MACH-3 Installation and Configuration Manual January 31, 2019 Revision 5.0...
- Page 2 WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright 2018 Machfu Inc. All rights reserved. Machfu and other trademarks are trademarks of Machfu Inc. Other trademarks may be trademarks of their respective owners. Simplifying IoT from edge to enterprise...
-
Page 3: Table Of Contents
MACH-3 Installation and Configuration Manual Table of Contents Table of Contents Overview ....................2 SYSTEM VIEWS ..............................2 1.1.1 Front Panel View ............................2 1.1.2 Right Side SIM Door View ...........................3 1.1.3 Bottom View ..............................3 Installing your MACH-3 Gateway .............4 PROFESSIONAL INSTALLATION INSTRUCTIONS ..................5 2.1.1... - Page 4 Table of Contents MACH-3 Installation and Configuration Manual WIRELESS INTERFACES ..........................14 3.3.1 Wi-Fi Client ..............................15 3.3.2 Wi-Fi Access Point............................15 3.3.3 Cellular ................................16 WIRED INTERFACES ............................17 3.4.1 Ethernet ..............................17 3.4.2 Serial ................................18 NETWORK ................................19 3.5.1 Bridge ................................. 20 3.5.2 VPN ................................20 3.5.3...
- Page 5 MACH-3 Installation and Configuration Manual Revision History Revision History Revision Description Date Initial release 1/4/2017 Revision 1/5/2018 Revision 8/1/2018 Revision 10/3/2018 Revision 1/31/2019 Simplifying IoT from edge to enterprise...
-
Page 6: Overview
1 Overview MACH-3 Installation and Configuration Manual 1. Overview The MACH-3 Gateway is an Industrial Internet- electric grid, oil & gas, manufacturing, and of-Things (IIoT) device. It is deployed on other applications. The MACH-3 Gateway has the MACH-3 Edge network, enabling you to... -
Page 7: Right Side Sim Door View
MACH-3 Installation and Configuration Manual 1 Overview 1.1.2 Right Side SIM Door View 1.66” 3.39” 1.1.3 Bottom View 6-32 mounting screw (x4) 1.22” Maximum length 1.25” 0.97” 3.35” Simplifying IoT from edge to enterprise... -
Page 8: Installing Your Mach-3 Gateway
If the WARNING: symbol indicates hot surface MACH-3 Gateway is to be installed in a wet or adjacent hot surface that can cause a burn. environment, depending on the location and Allow equipment to cool or use protective gloves environment, it must be installed in a panel when handling to reduce risk of a burn. -
Page 9: Professional Installation Instructions
2.2.3.1 Mounting Instructions Remove the two center screws from the base plate of the Machfu gateway. 2.1.2 Installation Location (marked with a red circle in the picture The product shall be installed at a location below.) -
Page 10: Setting Up Mach-3 Gateway
2 Installing your MACH-3 Gateway MACH-3 Installation and Configuration Manual 2.3 Setting up MACH-3 Gateway Connect an Ethernet RJ45 cable to The gateway power connector is a Ethernet 1 as shown in Figure 1: Front Molex Microfit 3.0 four pin connector Panel View. - Page 11 MACH-3 Installation and Configuration Manual Unscrew and remove the SIM door. Slide SIM card into holder through Replace and screw in the SIM door. opening and push until latch clicks. To remove push again until latch disengages, and slide SIM card out.
-
Page 12: Gateway Configuration
3.1.3 Navigation The MACH Gateway Configuration Tool is used The Mach Gateway Configuration Interface to configure MACH-3 Gateway products. This contains six main tabs, seen in the navigation User Guide describes how the tool can be bar on the left side of the interface. Each tab... -
Page 13: Dashboard
MACH-3 Installation and Configuration Manual 3 Gateway Configuration SETTINGS handles the user and SYSTEM handles system password management of the MACH upgrade, device reboot, remote Gateway. Page 26 provides details on support setting and applications the SETTINGS configuration pages. management. Page 29 provides details on the SYSTEM configuration pages. -
Page 14: Gps
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.2.2 GPS • Location – Latitude/Longitude of the Gateway. • Altitude – Altitude of the Gateway. • GPS Time – UTC time as received by GPS. • Satellites (In Use) – Number of GPS satellites in use by the Gateway. -
Page 15: Vpn
MACH-3 Installation and Configuration Manual 3 Gateway Configuration 3.2.4 VPN • Type – Type of VPN connection. • IP Address – IP address of VPN connection. • VPN UP/DOWN – Indicates if VPN connection is UP or DOWN. • VPN Server – IP address of VPN server. -
Page 16: Ethernet 2
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.2.6 Ethernet 2 • Status – Indicates if the Ethernet connection is Enabled or Disabled. • Link UP/DOWN – Indicates if the Ethernet link is UP or DOWN. • Link Speed – Data rate on the Ethernet 2 (eth1) Interface. -
Page 17: Wi-Fi Access Point
MACH-3 Installation and Configuration Manual 3 Gateway Configuration 3.2.8 Wi-Fi Access Point • Status – Indicates if the Wi-Fi Access Point is Enabled or Disabled. • SSID – Specifies the wireless network name or SSID (Service Set Identifier) used to identify the WLAN. -
Page 18: Wireless Interfaces
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.3 Wireless Interfaces The wireless interface configurations are used to configure the Wi-Fi and Cellular radios on the MACH Gateway. 3.3.1 Wi-Fi Client In the Client mode, the following configurations are seen •... -
Page 19: Wi-Fi Access Point
MACH-3 Installation and Configuration Manual 3 Gateway Configuration 3.3.2 Wi-Fi Access Point In the Access Point mode, the following configuration panel is seen. • Set the ‘Enable’ button to use the Wi-Fi in the access point mode • SSID – Specify the wireless network name or SSID (Service Set Identifier) used to identify the WLAN •... -
Page 20: Cellular
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.3.3 Cellular In the Cellular section, the following information is seen. • IMSI – The International Mobile Subscriber Identity (IMSI) identifies the user of the cellular network. • ICCID – The Integrated Circuit Card Identifier (ICCID) is a 19-digit identification number for SIM. -
Page 21: Wired Interfaces
MACH-3 Installation and Configuration Manual 3 Gateway Configuration 3.4 Wired Interfaces The MACH Gateway has two wired interfaces: Ethernet and Serial. However, the Ethernet has two ports: Ethernet 1 (eth0) and Ethernet 2 (eth1). To configure Ethernet or Serial interface, click the WIRED Tab on the left panel. -
Page 22: Serial
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.4.1.1 IP Addressing 3.4.1.7 Auto Negotiate If the Gateway has a static IP address, A procedure used by Ethernet in which two select ‘STATIC IP’ and enter the address in connected networking devices determine the IP address dialog box. -
Page 23: Network
MACH-3 Installation and Configuration Manual 3 Gateway Configuration 3.4.2.1 Protocol receiver. Set the FLOW CONTROL switch to The protocol selected for the serial ‘NONE’ to disable the handshaking method connection can be TCP/UDP. Set the or set it to ‘RTS/CTS’ to enable hardware PROTOCOL switch to ‘TCP’... -
Page 24: Bridge
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.5.1 Bridge VPN can be configured through Ethernet or Cellular. In the bridge mode, any broadcast that comes on the Wi-Fi, Ethernet 1 (eth0) or Ethernet 2 (eth1) ports are automatically sent over through the other 2 ports. - Page 25 MACH-3 Installation and Configuration Manual 3 Gateway Configuration • Type the peer tunnel ID in the L2TP PEER TUNNEL ID dialog box. The number can also be incremented and decremented by 1. • Type the peer session ID in the L2TP PEER SESSION ID dialog box.
-
Page 26: Open Vpn
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.5.3 Open VPN • Select authentication type as ‘RSA’ in the AUTHENTICATION TYPE dropdown list. Configure Open VPN on the MACH Gateway by setting the VPN switch to ‘OPENVPN’. The • Select ‘AES-128-CBC’ for 128-bit AES OpenVPN configuration panel is displayed: encryption or ‘AES-256-CBC’... - Page 27 MACH-3 Installation and Configuration Manual 3 Gateway Configuration 3.5.4.1 Table Columns/Fields • ACTIONS – It contains icons for deleting a rule/row or moving it upward or downward in the table. • # – It shows the ordering of the rows.
-
Page 28: Source Network Address Translation
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.5.4.4 Delete Existing Rule 3.5.4.5 Update Rules/Table An existing rule can be deleted by clicking The table is updated or refreshed whenever the trash icon in the ‘ACTIONS’ column. a change in the table is committed to However, the ‘SUBMIT’... -
Page 29: Routes
MACH-3 Installation and Configuration Manual 3 Gateway Configuration • DESTINATION ADDRESS 3.5.6.1 Table Columns/Fields • ACTIONS – It contains icons for deleting • ADDRESS – In display mode, a rule/row or moving it upward or it shows the IP address of the downward in the table. -
Page 30: Settings
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.6 SETTINGS The Settings tab has two sections on the left panel: ‘Profile’ and ‘Users & Roles’. 3.6.1 Profile 3.6.2 Users & Roles This section is only visible for users with administrative (admin) role. It allows the admin user to view all other users of the MACH Gateway, add new users, delete existing users and reset users’... - Page 31 MACH-3 Installation and Configuration Manual 3 Gateway Configuration • 3.6.2.2 Add/Register New User Click the ‘Add’ button to register the new To register/add a new user to the Gateway, user or click the ‘Cancel’ button to cancel follow the steps below.
-
Page 32: Reset User's Password
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.6.3 Reset User’s Password 3.6.2.3 Delete User To delete an existing user, follow the steps o reset the password of a user, follow the below. steps below. • Click on the trash icon in the ‘ACTION’... -
Page 33: System
MACH-3 Installation and Configuration Manual 3 Gateway Configuration 3.6.3.1 Show All Roles The ‘Roles’ table has two columns/fields: • ROLES – It displays the acceptable roles for the MACH Gateway. • USERS – It displays users of the MACH Gateway based on their assigned role. -
Page 34: System Upgrade
3 Gateway Configuration MACH-3 Installation and Configuration Manual 3.7.1 System Upgrade This page allows the user with the roles ‘admin’, ‘oem’ or ‘customer’ to perform the system image update. The following steps show how to update the system image of a MACH Gateway. - Page 35 MACH-3 Installation and Configuration Manual 3 Gateway Configuration • A pop-up dialog appears and it informs the user if the chosen action is successful or not. • Click the ‘Reboot’ button to confirm the action or click the ‘Cancel’ button to cancel the reboot action.
-
Page 36: Applications
STATUS – This indicates if the application/service is running (ENABLED) or not (DISABLED). • ENABLE – This contains a checkbox that allows the user to start or stop ‘Machfu Apps’. The checkbox is disabled for ‘System Apps’. This column appears only for users with ‘admin’ role. -
Page 37: Start/Stop App
MACH-3 Installation and Configuration Manual 3 Gateway Configuration 3.7.3.3 Delete/Uninstall App 3.7.4 Start/Stop App To delete a ‘Machfu app’, follow the o start(enable) or stop(disable) an app, instructions below: follow the steps below: • • Click the icon in the ‘ACTION’ field. - Page 38 3 Gateway Configuration MACH-3 Installation and Configuration Manual • The table refreshes automatically to show that the updated status of app. Simplifying IoT from edge to enterprise...
-
Page 39: Regulatory Notices
MACH-3 Installation and Configuration Manual 4 Regulatory Notices 4. Regulatory interference, including interference that may cause undesired operation of the device. Notices Industry Canada Statement FCC Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to This equipment has been tested and found... - Page 40 4 Regulatory Notices MACH-3 Installation and Configuration Manual Industry Canada Radiation Exposure Statement This radio transmitter with model: Mach3 Gateway has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
-
Page 41: Appendix
NOTE: Modifications to the device or use of unauthorized antennae as not expressly approved by Machfu is the sole responsibility of the user, configurator or operator, who must reassess the equipment in accordance to all applicable international Safety, EMC, and RF standards. -
Page 42: Contacting Machfu
MACH-3 Installation and Configuration Manual 5.3 Contacting Machfu For technical assistance or customer service issues please contact support@machfu.com. Simplifying IoT from edge to enterprise...