Related Manuals for AquaSure AS-PR50S
Summary of Contents for AquaSure AS-PR50S
- Page 1 PREMIER SERIES DRINKING WATER SYSTEM OWNER’S MANUAL FOR MODEL NO. AS-PR50S AS-PR75A AS-PR100P www.AquasureUSA.com 818 N Mountain Ave #203c, Upland, CA 91786 800.661.0680 | sales@aquasureusa.com...
-
Page 3: Table Of Contents
Replacing Stage 1 & 2 Pre-Filters Replacing Stage 3 & 4 RO membrane and Post Carbon Filter SYSTEM TROUBLESHOOTING LIMITED PRODUCT WARRANTY You can also visit online for system installation tutorial. http://www.aquasureusa.com/aquasure-ro-installation-guide-feed-water-adapter/ Manual Ver 1.0 - 05/2018 AQUASURE PREMIER SERIES... -
Page 4: Inspection & Preparation
WELCOME Thank you for choosing Aquasure. Before you start using your Aquasure drinking water system, take a few minutes to become familiar with the basics. Filter replacement Be sure to change your Aquasure water filters according to the recommended filter replacement schedule. This helps keep your Aquasure drinking water system running in top condition. - Page 5 Dia. A Instruction continues on the next page AQUASURE PREMIER SERIES...
-
Page 6: System Operation Parameters And Installation Checklist
II. System Operation Parameters and Installation checklist IMPORTANT! The following conditions for the feed water supply must be met or warranty will be void and manufacturer assumes no responsibility for damage to system or property. Water Temperature Parameters • Maximum: 105º F (40.6º C) •... -
Page 7: Feed Water Adapter With 3/8" Or 1/2" Connection Setup
Install the 3/8” to 1/2 inlet converter to the adapter by rotating counter-clockwise until tightened. Dia. B Rotate clockwise to tighten Please make sure there are O-rings inside the connector 3/8” Connection Rotate counter-clockwise to tighten 1/2” Connection Instruction continues on the next page AQUASURE PREMIER SERIES... -
Page 8: Quick Connect / Compression Fitting Installation Instruction
IV. Quick Connect / Compression Fitting Installation Instruction Note: This systems is equipped with quick connect fittings. These user-friendly fittings provide superior performance and leak-free seal if installed correctly. Quick Connect Tubing Installation Dia. C-1 CORRECT • Inspect Tubing (See Diagram C-1) - The system comes with pre-cut tubing that is cut cleanly and squarely to ensure proper connection. -
Page 9: Drinking Water Faucet Mounting Hole Preparation
Switch to 7/16” (11 mm) drill bit and operate the drill slowly and carefully— Especially when the drill bit is about to penetrate the metal. Otherwise, damage to sink may occur. Use lubricating oil to keep the drill bit cool while drilling. Instruction continues on the next page AQUASURE PREMIER SERIES... - Page 10 Drilling Stainless Steel • Use a hole punch and hammer to mark the location of where you want to install the faucet. Keep your taps short and control until a dent is visible, this will help keep your drill bit seated when start drilling.
- Page 11 AQUASURE PREMIER SERIES...
-
Page 12: Installing The System
INSTALLING THE SYSTEM WARNING! Do not proceed with the installation until you have gone over the System Operation Parameters and Installation Checklist section on page 4 of this owners manual and comply with all the conditions listed in that section. Failure to comply may result in property damage and your system warranty will be voided due to non-compliance with the operation parameters. - Page 13 Note: If the hole in the copper tube is not adequately pierced, this may prevent sufficient cold water supply to flow to the system and reduce the system performance. In this event, open and close the self-piercing valve several times to ensure an adequate pierced tube. Dia. D-3 Instruction continues on the next page AQUASURE PREMIER SERIES...
-
Page 14: Step 2. Drain Saddle Installation
STEP 2. Drain Saddle Installation Locate the optimal placement on the drain pipe to install the drain saddle. (See Diagram E-1) Note: The drain saddle should be installed above the trap and on the vertical or horizontal tail piece. To reduce potential drainage noise, it is ideal to mount the drain saddle as low as possible on the vertical pipe above the trap or on the horizontal tail piece. -
Page 15: Step 3. Tank Ball Valve Installation
CAUTION! Do Not over tighten the adapter to avoid breaking and leak. Attached the faucet adapter to the shank. Counter Faucet Base Black Washer Lock Washer Faucet Shank Chrome Nut Faucet Adapter Pure Water Line Instruction continues on the next page AQUASURE PREMIER SERIES... -
Page 16: Step 5. Mounting Or Placement Of The System
STEP 5. Mounting or Placement of the System WARNING! If mounting the system is not an option, please make sure system is installed in a space with secure footing. Improper placement of the system may cause the system to tip over and break due to the added weight of the water. -
Page 17: Step 6. Connecting The System
Note: if you purchase the optional extra-output kit, please follow to supplied installation instruction first before moving on to the next step. Dia. I-1 Kitchen Counter Drain Pipe Cold water Line Supply Water Valve Instruction continues on the next page AQUASURE PREMIER SERIES... -
Page 18: Step 7. System Startup
STEP 7. System Startup WARNING! Immediately shut off the cold water supply valve or main water supply valve if there are leaks. Check the leak area and see if there’s a loose connection or if more Teflon tape is needed to prevent leaks from happening. - Page 19 You have finished installing your very own drinking water system. Don’t forget to register your system to get additional 2 years of limited warranty. Simply scan the QR code using your mobile phone, or go directly to our website http://www.aquasureusa.com/warranty-registration to begin the online registration process. AQUASURE PREMIER SERIES...
-
Page 20: System Maintenance
SYSTEM MAINTENANCE Note: The system requires very little maintenance as long as the filter cartridges are regularly replaced at the recommended time frame. Please only use genuine Aquasure replacement filter at http://www.aquasureusa.com/water-filter/drinking-water/premier Filter Replacement Time Frame • Pre-Stage Filters: Replace every 6 to 12 months (Private well water source may need to replace pre-filters sooner than 12 months due to heavy sediments and other particulates.) -
Page 21: Replacing Stage 1 & 2 Pre-Filters
Repeat the same process for stage 2. Turn ON cold water supply and Tank Ball Valve. Check for leaks. Secure the FLOWLOK tray by screwing the locking screw behind the filters. Instruction continues on the next page AQUASURE PREMIER SERIES... -
Page 22: Replacing Stage 3 & 4 Ro Membrane And Post Carbon Filter
III. Replacing Stage 3 & 4 RO membrane and Post Carbon Filter Turn OFF cold water supply from the feed Twist the RO-Membrane and Post-Stage water adapter to the system. Taste Refining Filter quarter turn to the right to unseat the filters from the system. Turn on the dispensing faucet to empty out the tank and store all the product water in a Replace the system with new RO-Membrane... - Page 23 AQUASURE PREMIER SERIES...
-
Page 24: System Troubleshooting
SYSTEM TROUBLESHOOTING IMPORTANT! Please shut off cold water supply valve to the system if the system is malfunctioning or leaking and contact our support department immediately! For any system troubleshooting, feel free to contact our support department at 1-800-661-0680 during our business hour of Monday - Friday from 8:30 am ~ 5:30 pm PDT. - Page 25 New carbon post-filter has not been rinsed Drain holding tank twice to rinse new carbon post- completely filter The incoming feed water TDS has increased An increase in feed water TDS will also give an increase in product water TDS AQUASURE PREMIER SERIES...
- Page 26 6. Faucet leaks or drips CAUSE: CORRECTION: Water leaks from faucet spouts Adjust the faucet by turning the tee bar located under the handle to provide a small amount of free play in the handle when shut off. Should this not work, repair or replace the faucet.
- Page 27 System is feeding multiple outlets or an outlet It is normal in this situation as system needs to that demands water constantly. constantly produce water to supply the multiple outlets. AQUASURE PREMIER SERIES...
- Page 28 Disclaimer of warranties. Except as expressly warranted in writing by, the goods sold by AQUASURE are purchased by the buyer “as is. ” AQUASURE does not warrant that the goods are of merchantable quality or that they can be used for any particular purpose. Except as expressly warranted in writing by AQUASURE, AQUASURE makes no representation or warranty of any kind with respect to the products.
-
Page 29: Limited Product Warranty
Aquasure cannot verify or guarantee the integrity or authenticity of the Product. Limitation of liability. In no event shall AQUASURE be liable to the purchaser or any other entity for more than the invoice price received by AQUASURE for any non-conforming products. AQUASURE shall not be liable to... - Page 30 The products described in this document are hereby offered for sale to be established goods sent from 3rd party marketplace. by Aquasure any of its subsidiaries and its authorized distributors. This offer and its (c) Unless provided otherwise, delivery of the goods shall be made when the Seller has acceptance by any customer (the “Buyer”) shall be governed by all of the following...
- Page 31 PROFESSIONAL; AND (III) INSTALLED AND OPERATED IN ACCORDANCE WITH item sold hereunder. The foregoing in this provision shall constitute the Seller’s sole PUBLISHED AQUASURE DRINKING WATER SYSTEM SPECIFICATIONS. and exclusive liability and the Buyer’s sole and exclusive remedy for infringement of (c) All costs and expenses, including freight charges, customs duties, and insurance Intellectual Property Rights.
- Page 32 www.AquasureUSA.com | 818 N Mountain Ave #203c, Upland, CA 91786 | 800.661.0680 | sales@aquasureusa.com...
Need help?
Do you have a question about the AS-PR50S and is the answer not in the manual?
Questions and answers