Table of Contents
Advertisement
Quick Links
Technical documentation
Wheel sensor Signal Converter
Pos: 2 /MO DULE /0 0 _ Int ro/Allg emein es/0 1 _ Fu ßzeil e_ 0 2 @ 4 \mod _ 1 4 2 44 1 65 1 47 9 5_ 29 0 1 .d ocx @ 5 2 2 8 4 @ @ 1
Tel. +43 (0) 7711 2920-0 | Fax +43 (0) 7711 2920-25
Name
Prepared:
Susanna Schachinger
Checked:
Released:
© Frauscher Sensortechnik GmbH – All rights reserved. The reprinting, reproduction, storage on or in any data media or in any retrieval system, even if only in the form of extracts,
or the transfer to third parties, is only permitted with the express written consent of Frauscher Sensortechnik GmbH.
Pos: 3 /MO DULE /0 0 _ Int ro/Allg emein es/0 2 _ Imp ressu m_ Mein u n g_ oh n e "DE Orig in al" _ 0 1 @ 3 \mod _ 1 4 17 8 69 7 86 8 86 _ 29 01 .d ocx @ 4 3 3 0 9 @ @ 1
D4586-0.2
WSC001
Frauscher Sensortechnik GmbH
Gewerbestraße 1 | 4774 St. Marienkirchen | Austria
office@frauscher.com | www.frauscher.com
Signature
Date
2016-07-12
Technical documentation
Wheel sensor Signal Converter
WSC001
Classified
D4586-0.2
EN
1 / 62
Advertisement
Table of Contents
Related Manuals for Frauscher Sensortechnik GmbH WSC001
Summary of Contents for Frauscher Sensortechnik GmbH WSC001
- Page 1 1 / 62 © Frauscher Sensortechnik GmbH – All rights reserved. The reprinting, reproduction, storage on or in any data media or in any retrieval system, even if only in the form of extracts, or the transfer to third parties, is only permitted with the express written consent of Frauscher Sensortechnik GmbH.
- Page 2 Masthead Copyright 2016 by Frauscher Sensortechnik GmbH – Austria The content of this documentation may not be reproduced in any form, either partially or as a whole, nor disclosed to third parties without prior written consent of Frauscher. All trademarks or registered trademarks mentioned herein are property of their respective owners.
-
Page 3: Table Of Contents
Interface “optocoupler output 1 and 2” ................23 3.1.4.1 Interface “optocoupler output 3 and 4” ................23 3.1.4.2 Basic conditions for the installation ..........24 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 3 - © 2016 by Frauscher Sensortechnik GmbH – Austria... - Page 4 Traversing in direction 2 ....................44 6.4.3 Behaviour in case of wire break ..................45 6.4.4 Behaviour in case of overcurrent ................... 46 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 4 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
- Page 5 Pos: 7 /MO DULE /Neu t rale u n d St eu ermod u le/---------------- ---- Seit en u mb ru ch ----------- --------- @ 0 \mod _ 13 8 99 5 44 6 24 31 _ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 5 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
-
Page 6: Review List
Pos: 1 5 /MODU LE /Neu t rale u n d St eu ermod u le/-------------------- Seit en u mbru ch -------- --------- --- @ 0 \mod _ 1 3 89 9 54 4 62 43 1 _0 .d ocx @ 1 1 0 2 5 @ @ 1 The stated or a higher version is valid. D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 6 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 7: List Of Standards
Pos: 2 8 /MODU LE /Neu t rale u n d St eu ermod u le/-------------------- Seit en u mbru ch -------- --------- --- @ 0 \mod _ 1 3 89 9 54 4 62 43 1 _0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 7 - © 2016 by Frauscher Sensortechnik GmbH – Austria... - Page 8 === E n d e d er List e fü r Te xt mark e In h alt = == D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 8 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
-
Page 9: About This Documentation
This documentation provides information of the product features and the required information for the configuration and installation of the Wheel sensor Signal Converter WSC001. Pos: 3 4 /MODU LE /0 1 _ Üb er d iese D oku men t at ion /Darst ellu n g skon ven t ion en /### Darst ellu n g skon ven t ion en ## # _ 0 1 @ 1 \mod _ 1 3 9 3 4 21 0 98 41 3 _2 9 01 .d ocx @ 1 4 1 8 8 @ 2 @ 1 1.1 Typographical conventions... -
Page 10: Units Of Measurement
Pos: 5 2 /MODU LE /Neu t rale u n d St eu ermod u le/-------------------- Seit en u mbru ch -------- --------- --- @ 0 \mod _ 1 3 89 9 54 4 62 43 1 _0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 10 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 11: Abbreviations
Pos: 7 6 /MODU LE /0 1 _ Üb er d iese D oku men t at ion /Ab kü rzu n g en /Ri2_ 0 1 @ 4 \mod _ 1 43 99 8 32 7 18 3 2_ 2 90 1 .d ocx @ 6 5 5 3 5 @ @ 4 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 11 - © 2016 by Frauscher Sensortechnik GmbH – Austria... - Page 12 Pos: 8 9 /MODU LE /Neu t rale u n d St eu ermod u le/-------------------- Seit en u mbru ch -------- --------- --- @ 0 \mod _ 1 3 89 9 54 4 62 43 1 _0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 12 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
-
Page 13: Terms And Definitions
Pos: 1 0 0 /MODULE /0 1 _ Üb er d iese Do ku men t at ion /Beg riffsb e st immu n g en /Üb erst romp eg el_ 0 1 @ 1 \mod _ 13 9 35 7 99 6 04 9 2_ 2 90 1 .d ocx @ 1 5 3 7 8 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 13 - © 2016 by Frauscher Sensortechnik GmbH – Austria... - Page 14 Pos: 1 0 8 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 14 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
-
Page 15: Target Group
Pos: 1 2 0 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 15 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 16: Safety-Conscious Working
Pos: 1 2 9 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 16 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 17: Structure And Function
Pos: 1 3 2 /MODULE /5 0 _ Komp on en t en d oku s/WSC/0 3 -2_ E rkläru n g Gleisp lan _ 0 1 @ 6 \mod _ 1 46 6 58 4 48 4 36 3 _2 90 1 .d ocx @ 8 6 4 4 7 @ @ 4 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 17 - © 2016 by Frauscher Sensortechnik GmbH – Austria... - Page 18 The required information and prerequisites for the application of the wheel sensor RSR110-001 are described in the documentation D4232 “Application guide wheel sensor RSR110”. D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 18 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
- Page 19 Pos: 1 3 4 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 19 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
-
Page 20: Interfaces
Pos: 1 3 7 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 20 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 21: Diagnostic Interface "Serial Interface
The permissible supply voltage is 10 to 36 V DC. The current consumption of the WSC varies depending on the connected wheel sensor(s). D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 21 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 22: Interfaces "Optocoupler Outputs
The interfaces “optocoupler outputs” consist of the interface “optocoupler output 1 and 2” and the interface “optocoupler output 3 and 4”. D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 22 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 23: Interface "Optocoupler Output 1 And 2
Pos: 1 4 4 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 23 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 24: Basic Conditions For The Installation
Pos: 1 4 9 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 24 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 25: Configuration
≤ 1 mm or another small tool with a fine tip. • When delivered the DIP-switches are set to “OFF”. D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 25 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 26: Dip-Switches Of The Wsc
If the normal status is configured with “open”, the 4-edges direction pulse is not output in case failures and/or errors occur (e.g. wire break, overcurrent). D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 26 - © 2016 by Frauscher Sensortechnik GmbH – Austria... - Page 27 It is recommended to use this configuration with 1 wheel sensors RSR110-002. Table 5.2: Configuration of system outputs and/or direction outputs D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 27 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
-
Page 28: Configuration Of The Normal Status Of All Optocoupler Outputs
It is not possible to configure the normal status of the error output. The normal status of the error output is closed. D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 28 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 29: Configuration Of The Output Extension Time
In case a configuration without system outputs is chosen, the DIP-switches with the DIP-no. 4 and 5 must be set to “OFF”. D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 29 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 30: Configuration Of The Direction Pulse Length
Pos: 1 5 3 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 30 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 31: Signal Diagrams
“Sys” and “Ri” are inverted to the respective signals in the following diagram. Figure 6.1: Traversing in direction 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 31 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 32: Traversing In Direction 2
“Sys” and “Ri” are inverted to the respective signals in the following diagram. Figure 6.2: Traversing in direction 2 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 32 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 33: Behaviour In Case Of Wire Break
If the configuration “open in normal status” is selected, then in case of wire break, the system and/or direction outputs remain in the open status. Figure 6.3: Behaviour in case of wire break D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 33 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 34: Behaviour In Case Of Overcurrent
If the configuration “open in normal status” is selected, then in case of overcurrent, the system and/or direction outputs remain in the open status. Figure 6.4: Behaviour in case of overcurrent D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 34 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 35: Configuration Of 2 Direction Outputs And 1 Error Output
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.5: Traversing in direction 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 35 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 36: Traversing In Direction 2
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.6: Traversing in direction 2 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 36 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 37: Behaviour In Case Of Wire Break
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.7: Behaviour in case of wire break D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 37 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 38: Behaviour In Case Of Overcurrent
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.8: Behaviour in case of overcurrent D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 38 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 39: Configuration Of 2 System Outputs And 1 Error Output
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.9: Traversing in direction 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 39 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 40: Traversing In Direction 2
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.10: Traversing in direction 2 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 40 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 41: Behaviour In Case Of Wire Break
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.11: Behaviour in case of wire break D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 41 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 42: Behaviour In Case Of Overcurrent
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.12: Behaviour in case of overcurrent D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 42 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 43: Configuration Of 1 System Output And 1 Error Output
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.13: Traversing in direction 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 43 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 44: Traversing In Direction 2
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.14: Traversing in direction 2 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 44 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 45: Behaviour In Case Of Wire Break
It is not possible to configure the normal status of the error output, therefor the signal for the error output is identical to the displayed signal at the error output. Figure 6.15: Behaviour in case of wire break D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 45 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 46: Behaviour In Case Of Overcurrent
Pos: 1 5 5 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 46 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 47: Installation
If boards without packaging are handed from one person to another, hands of the participants must be touched to balance potential before handover. D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 47 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 48: Wiring Of The Wsc
Pos: 1 5 9 /MODULE /5 0 _ Komp on en t en d oku s/WSC/0 7 -2_ ### In st all at ion # ##_ 0 1 @ 5 \mod _ 1 4 5 0 18 9 82 3 62 1 _2 9 01 .d ocx @ 7 1 9 6 6 @ 2 @ 4 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 48 - © 2016 by Frauscher Sensortechnik GmbH – Austria... - Page 49 Sys2- (white wire) Figure 7.5: Interfaces of the WSC for Figure 7.6: Wires of the wheel sensor cable the wiring D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 49 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
- Page 50 2” OUT1- OUT2+ OUT2- “optocoupler output 3 OUT3+ and 4” OUT3- OUT4+ OUT4- Table 7.1: Pin assignment of the WSC D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 50 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
-
Page 51: Mounting And Dismounting Of The Wsc
Figure 7.7: Mounting of the WSC on the top- Figure 7.8: Mounting of the WSC on the top-hat rail, step 2 hat rail, step 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 51 - © 2016 by Frauscher Sensortechnik GmbH – Austria... - Page 52 Pos: 1 6 0 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 52 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
-
Page 53: Commissioning
AMB001. When combined with a conventional voltmeter, the AMB serves to provide automatic adjustment of the wheel sensor RSR110-001 and the wheel sensor RSR110-002. D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 53 - © 2016 by Frauscher Sensortechnik GmbH – Austria... - Page 54 Pos: 1 6 5 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 54 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
-
Page 55: Maintenance
• check cable connecting terminals for correct fitting • a check of measurement A D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 55 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 56: Check Of The Sensor Current Of The Wheel Sensor
“wheel sensor” (see following figures) and then insert the other side of the black (or blue) test lead into the jack “COM” of the multimeter. D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 56 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 57: Check Of The Occupancy Detection Capability
(see documentation D2860 “Brief instruction testing plate PB200 GS03”). • For this the associated outputs of the WSC must switch correctly. D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 57 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 58: Repair
(rail claw mounting, rail web mounting, etc.) • the rail profile (large e.g. UIC60, small e.g. VST36) D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 58 - © 2016 by Frauscher Sensortechnik GmbH – Austria... -
Page 59: Led Indications On The Wsc
Table 10.2: LED “PWR” off In case the LED “PWR” is illuminated, this indicates an operating status: illuminated time Figure 10.2: LED “PWR” illuminated D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 59 - © 2016 by Frauscher Sensortechnik GmbH – Austria... - Page 60 Table 10.5: LED “Sys1” and/or “Sys2” illuminated D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 60 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
- Page 61 Pos: 1 7 8 /MODULE /Neu t ral e u n d St eu ermod u le/------------------ -- Seit en u mb ru ch ---- ---------- ------ @ 0 \mod _ 1 38 9 95 4 46 24 3 1_ 0 .d ocx @ 1 1 0 2 5 @ @ 1 D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 61 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
-
Page 62: Removal From Service
=== E n d e d er List e fü r Te xt mark e K ap it el1 = == D4586-0.2 Classified Technical documentation Wheel sensor Signal Converter WSC001 - 62 - © 2016 by Frauscher Sensortechnik GmbH – Austria...
Need help?
Do you have a question about the WSC001 and is the answer not in the manual?
Questions and answers