Table of Contents
Related Manuals for RivieraPool Vitara
Summary of Contents for RivieraPool Vitara
- Page 1 Technical Information WP 10 B 09/2009 instructions for installation and Use P O R T A B L E S P A S V i TA R A , V i A n O , S i E n n A , S i E n n A X L , P E n TA r e fa b r i c at e d w i m m i n g o o l S...
-
Page 2: Table Of Contents
Content 1. Preconditions Subsoil/Foundation Page ....................................................Power supply Page .......................................................... Fresh water Page ..........................................................Waste water Page ..........................................................Delivery Page ............................................................... noise insulation Page ......................................................2. Start up and use installing the whirlpool Page ................................................. initial activation/Switching the power supply on and off Page ....................... -
Page 3: Preconditions
Preconditions 1. Preconditions 1.1 Subsoil / Foundation The foundation should be level, firm and have the same dimensions as the whirlpool (see specifications for measurements). The entire base of the whirlpool must lie absolutely flat on the ground so that its weight is properly supported. -
Page 4: Start Up And Use
Start up and use 2. Start up and use Installing the whirlpool The whirlpool should be installed on a firm and level foundation. The surface upon which the pool is to be placed should be checked to make sure it is perfectly flat. Similarly, a check should be carried out with a spirit level to ensure that the whirlpool is standing even. -
Page 5: Operation Of Pools
Start up and use 2.8 Start up and use 2.8.1 Jet 1 (jet nozzles) Massage pump Jet 1 will be switched on and off by pressing the Jet 1 but- ton. Should the pump not be switched off manually it will automatically start again after 15 minutes. -
Page 6: Cascade
Start up and use All models except the Penta P are equipped with a cascade. 2.8.4 Cascade The water cascade is fed by the filter pump and only operates when the filter pump runs. The filtration time is programmed from 08:00hrs until 22:00hrs and 18:00hrs 22:00hrs. -
Page 7: Operating Mode
Start up and use 2.8.7 Operating mode Mode/Prog: This control button is used to switch between the three operat- ing modes – STAnDARD, ECOnOMY and SLEEP. To program the mode, press the „Mod/Prog“ button, then press „Cool“ to switch through to the desired mode (LCD light flashes to acknowledge), and finally „Mode/Prog“... -
Page 8: Care And Maintenance
Care and maintenance 3. Care and maintenance Water maintenance Thorough water maintenance forms the basis for a hygienic whirlpool. Clean and clear water is visually appealing and contributes considerably to the overall feeling of well being. inadequate water maintenance can have an adverse effect on one’s health. -
Page 9: Ph-Value
Care and maintenance The pH-value in the whirlpool should be between 7.2 and 7.4. This is the 3.1.3 pH value ideal level for a disinfectant to work most efficiently and the water feels soft to the skin and is not corrosive. The strong addition of air when the massage jets are in use means that there can very quickly be a big increase in the pH value. -
Page 10: Cleaning And Maintenance Of The Wooden Surfaces
Care and maintenance ATTENTION! Please do not use any solvent-containing cleaners as they might affect the acrylic surface. Dull surfaces can be polished up so that they shine even after years. A special surface polish called „Poolfinish“ is available for just this purpose. This is applied with a soft cotton cloth and polished with gentle circular movements. -
Page 11: Instructions For Bathing
Instructions for bathing 4. Instructions for bathing Water temperatures in whirlpools are significantly higher than those for instance of whirlpools. This is so, because it is through the combination of heat and the movement of the water that the desired feeling of relaxation can be achieved. -
Page 12: Diagnostic Messages / Regular Reminders
Diagnostic Messages / Regular Reminders 5. Diagnostic Messages / Regular Reminders Diagnostic Meaning Action required message No message displayed The power supply to the The operator console remains switched off until the power is restored. The whirlwhirlwhirlpool controls is disconnected. whirlpool controls settings are stored for up to 30 days with the assistance of Temperature not known. - Page 13 Diagnosemeldungen Diagnostic Meaning Action required message Temperature not recognised. After the pump has been switched on for 2 minutes, the temperature is displayed. Current temperature not in sleep or save mode. In sleep or save mode and outside a filter cycle, the pump stays switched off, potentially for a number of hours.
- Page 14 Notes...
- Page 15 Notes...
- Page 16 www.pools.de One of the leading German manufacturers of prefabricated swimming pools, swimming pool technology.
Need help?
Do you have a question about the Vitara and is the answer not in the manual?
Questions and answers