Do you have a question about the Platinum Blood Pressure Monitor and is the answer not in the manual?
Questions and answers
Dennis Paulazzo
January 25, 2025
Do you have a question about the Platinum Blood Pressure Monitor----
states to move but not in the manual?
2 comments:
Dennis Paulazzo
January 25, 2025
How do you move a decimal point to read correctly--- states to move but not
how in the manual?
Mr. Anderson
February 10, 2025
The term "move" in the Care Touch Platinum Blood Pressure Monitor manual refers to the process of progressing through different settings when configuring the device. For example, when setting the date, time, or measurement unit, users press the "set" button to confirm a selection and "mem" to adjust values before moving to the next option.
For more information, refer to the "How to set up your monitor" section in the quick guide, which explains the step-by-step process of setting up the device.
This answer is automatically generated
John W Boron
May 12, 2025
My sys is 26.5 and dia is 13.2. Why is it displaying tenths?
1 comments:
Mr. Anderson
May 20, 2025
The Care Touch Blood Pressure Monitor is displaying tenths for systolic 26.5 and diastolic 13.2 because it is set to display measurements in kilopascals (kPa) instead of millimeters of mercury (mmHg). In kPa, values are shown as decimal points, which can be confusing if you expect mmHg. You need to change the unit setting to mmHg for standard readings.
This answer is automatically generated
Karen
March 28, 2025
My CareTouch monitor will not turn on, new batteries and installed properly
1 comments:
Mr. Anderson
March 28, 2025
If your Care Touch Platinum Blood Pressure Monitor won't turn on even with new batteries installed properly, possible reasons include:
1. The batteries may be depleted or not inserted with correct polarity (+/-). 2. The battery contacts may be dirty or corroded. 3. The monitor may be damaged or malfunctioning. 4. The power button may not be pressed correctly or held long enough. 5. The device may have been exposed to strong electromagnetic fields or electrical interference.
If none of these apply, the unit may need service or replacement.
This answer is automatically generated
Denise Stinson
March 14, 2025
What does message mmHg indicate?
The cuff has new batteries; the date and time are correct. The start screen appears as normal, but the unit will not engage to complete blood pressure check
1 comments:
Mr. Anderson
May 14, 2025
The mmHg message indicates the measurement unit of blood pressure (millimeters of mercury), not an error. If the monitor will not engage to complete a blood pressure check, the issue may be due to low or incorrectly inserted batteries, or an improperly secured cuff.
This answer is automatically generated
Sharon Gallo
February 25, 2025
Does this show AFIB
1 comments:
Mr. Anderson
February 25, 2025
The Care Touch Platinum Blood Pressure Monitor detects irregular heartbeats and displays an irregular heartbeat (IHB) symbol if a pulse irregularity is detected. However, the manual states that this does not replace a cardiac examination. It does not specifically mention detecting atrial fibrillation (AFIB).
This answer is automatically generated
George A Mitchell
February 8, 2025
On my BP MOnitor when setting the various items the program marches through date and time and then there are three or four VERY SMALL ICONS which I cannot read and don't know what they are settings for...advise what I can or should do with those.
1 comments:
Mr. Anderson
February 11, 2025
The small icons on the Care Touch Platinum Blood Pressure Monitor during the setup process represent different settings and measurement indicators. These include:
- Year, Month, and Day: Used to set the date. - Time Format (12h or 24h), Hour, and Minute: Used to set the time. - Measurement Unit (mmHg or kPa): Allows selection between different pressure units. - Irregular Heartbeat Symbol: Appears if a pulse irregularity is detected during measurement.
These icons help guide the user through the setup and monitoring process.
This answer is automatically generated
ANTONETTE
January 23, 2025
WHY **** I GETTING DIGITAL READING
1 comments:
Mr. Anderson
February 10, 2025
The Care Touch Platinum Blood Pressure Monitor may not provide a digital reading for the following reasons:
1. Pulse Signal Not Detected – If the monitor does not detect a pulse signal, it will not display a reading. Try loosening clothing on the wrist, relaxing, and measuring again. 2. Incorrect Measurement – If the measurement is performed incorrectly, the monitor may not display a reading. Ensure proper positioning and follow the instructions carefully. 3. Calibration Error (EExx Error Code) – A calibration error could prevent the monitor from functioning correctly. If this occurs, contact customer service for assistance.
If the problem persists, consider reaching out to the retailer or customer service for support.
This answer is automatically generated
Elizabeth Hinkle
July 13, 2025
My wrist cuff will not inflate
RaeAnn
July 12, 2025
This CareTouch monitor does not have SET button. How do I reset date & time?
Suzanne
May 17, 2025
Replace batteries, how to open
Related Manuals for Care Touch Platinum Blood Pressure Monitor
CATALOGUE CATALOGUE INTRODUCTION ............... 2 General Description Safety Information Indications for use Measurement principle LCD Display Signal Monitor Components BEFORE YOU START ............5 Installing and Replacing the Batteries Setting Date, Time and Measurement Unit MEASUREMENT ............... 9 Tie the Cuff Start the Measurement DATA MANAGEMENT ............
CAUTION General Description This device is intended for adult use only. Thank you for selecting CARE TOUCH This device is intended for no-invasive measuring and monitoring of arterial blood Fully Automatic Wrist Blood Pressure Monitor (PSW01). pressure. It is not intended for use on extremities other than the wrist or for functions The monitor features blood pressure measurement, pulse rate measurement and other than obtaining a blood pressure measurement.
BEFORE YOU START BEFORE YOU START Setting Date, Time and Measurement Unit Installing and Replacing the Batteries It is important to set the clock before using your blood pressure • .Open the battery cover. monitor, so that a time stamp can be assigned to each record that is •...
BEFORE YOU START MEASUREMENT Tie the Cuff 4.Repeat steps 2 and 3 to confirm [MONTH] and [DAY]. .Remove all accessories (watch,bracelet,etc) from your wrist.If your physician has diagnosed you with poor circulation in your wrist,use the other one. 2. Roll or push up your sleeve to expose the skin. 3.
MEASUREMENT DATA MANAGEMENT Recall the Records Start the Measurement When the monitor is off, press “MEM” button to 1.When the monitor is off, show the latest measurement press the START/STOP to turn on record. the monitor, and it will finish the whole measurement.
DATA MANAGEMENT INFORMATION FOR USER Tips for Measurement Delete the Records If you did not get the correct measurement, you can delete all Measurements may be inaccurate if taken in the following results by following steps below. circumstances. In the memory mode, hold pressing “MEM”...
Please note that the device does not replace a cardiac • Please report to CARE TOUCH if any unexpected operation or events occur. examination, but serves to detect pulse irregularities at an early stage.
ABOUT BLOOD PRESSURE TROUBLESHOOTING Why does my blood pressure This section includes a list of error messages and frequently asked questions for problems you may encounter with your wrist fluctuate throughout the blood pressure monitor. If the products not operating as you day? think it should, check here before arranging for servicing.
EMC GUIDANCE Table 2 Guidance and MANUFACTURER’s declaration – electromagnetic EMC GUIDANCE IMMUNITY – for all ME EQUIPMENT and ME SYSTEMS 1) * This product needs special precautions regarding EMC and needs to be Guidance and manufacturer’s declaration – electromagnetic immunity installed and put into service according to the EMC information provided, and The device is intended for use in the electromagnetic environment specified below.
Page 13
Table 6 Recommended separation distances between portable and mobile Table 4 Guidance and MANUFACTURER’s declaration – electromagnetic IMMUNITY – RF communications equipment and the ME EQUIPMENT or ME SYSTEM – for ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING for ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING Guidance and manufacturer’s declaration –...
Need help?
Do you have a question about the Platinum Blood Pressure Monitor and is the answer not in the manual?
Questions and answers
Do you have a question about the Platinum Blood Pressure Monitor---- states to move but not in the manual?
How do you move a decimal point to read correctly--- states to move but not how in the manual?
The term "move" in the Care Touch Platinum Blood Pressure Monitor manual refers to the process of progressing through different settings when configuring the device. For example, when setting the date, time, or measurement unit, users press the "set" button to confirm a selection and "mem" to adjust values before moving to the next option.
For more information, refer to the "How to set up your monitor" section in the quick guide, which explains the step-by-step process of setting up the device.
This answer is automatically generated
My sys is 26.5 and dia is 13.2. Why is it displaying tenths?
The Care Touch Blood Pressure Monitor is displaying tenths for systolic 26.5 and diastolic 13.2 because it is set to display measurements in kilopascals (kPa) instead of millimeters of mercury (mmHg). In kPa, values are shown as decimal points, which can be confusing if you expect mmHg. You need to change the unit setting to mmHg for standard readings.
This answer is automatically generated
My CareTouch monitor will not turn on, new batteries and installed properly
If your Care Touch Platinum Blood Pressure Monitor won't turn on even with new batteries installed properly, possible reasons include:
1. The batteries may be depleted or not inserted with correct polarity (+/-).
2. The battery contacts may be dirty or corroded.
3. The monitor may be damaged or malfunctioning.
4. The power button may not be pressed correctly or held long enough.
5. The device may have been exposed to strong electromagnetic fields or electrical interference.
If none of these apply, the unit may need service or replacement.
This answer is automatically generated
What does message mmHg indicate? The cuff has new batteries; the date and time are correct. The start screen appears as normal, but the unit will not engage to complete blood pressure check
The mmHg message indicates the measurement unit of blood pressure (millimeters of mercury), not an error. If the monitor will not engage to complete a blood pressure check, the issue may be due to low or incorrectly inserted batteries, or an improperly secured cuff.
This answer is automatically generated
Does this show AFIB
The Care Touch Platinum Blood Pressure Monitor detects irregular heartbeats and displays an irregular heartbeat (IHB) symbol if a pulse irregularity is detected. However, the manual states that this does not replace a cardiac examination. It does not specifically mention detecting atrial fibrillation (AFIB).
This answer is automatically generated
On my BP MOnitor when setting the various items the program marches through date and time and then there are three or four VERY SMALL ICONS which I cannot read and don't know what they are settings for...advise what I can or should do with those.
The small icons on the Care Touch Platinum Blood Pressure Monitor during the setup process represent different settings and measurement indicators. These include:
- Year, Month, and Day: Used to set the date.
- Time Format (12h or 24h), Hour, and Minute: Used to set the time.
- Measurement Unit (mmHg or kPa): Allows selection between different pressure units.
- Irregular Heartbeat Symbol: Appears if a pulse irregularity is detected during measurement.
These icons help guide the user through the setup and monitoring process.
This answer is automatically generated
WHY **** I GETTING DIGITAL READING
The Care Touch Platinum Blood Pressure Monitor may not provide a digital reading for the following reasons:
1. Pulse Signal Not Detected – If the monitor does not detect a pulse signal, it will not display a reading. Try loosening clothing on the wrist, relaxing, and measuring again.
2. Incorrect Measurement – If the measurement is performed incorrectly, the monitor may not display a reading. Ensure proper positioning and follow the instructions carefully.
3. Calibration Error (EExx Error Code) – A calibration error could prevent the monitor from functioning correctly. If this occurs, contact customer service for assistance.
If the problem persists, consider reaching out to the retailer or customer service for support.
This answer is automatically generated
My wrist cuff will not inflate
This CareTouch monitor does not have SET button. How do I reset date & time?
Replace batteries, how to open