Advertisement
Quick Links
Visit our website at
www.HDWELD.co.kr
www.hyundaiwelding.com
HEAD OFFICE : ILSONG BLDG. 16th fl.157-37,
SAMSUNG-DONG, KANGNAM-KU, SEOUL, KOREA
TEL : (+82-2)6230-6062 5 FAX: (+82-2)522-2030
FACTORY
: 9-2, SAEUM-DONG, ICHEON-SI, GYEONGGI-DO, KOREA
TEL : (+82-31)636-3100 FAX: (+82-31)636-3957
～
Advertisement
Related Manuals for HYUNDAI WELDING HiEGW 600W
Summary of Contents for HYUNDAI WELDING HiEGW 600W
- Page 1 Visit our website at www.HDWELD.co.kr www.hyundaiwelding.com HEAD OFFICE : ILSONG BLDG. 16th fl.157-37, SAMSUNG-DONG, KANGNAM-KU, SEOUL, KOREA TEL : (+82-2)6230-6062 5 FAX: (+82-2)522-2030 ～ FACTORY : 9-2, SAEUM-DONG, ICHEON-SI, GYEONGGI-DO, KOREA TEL : (+82-31)636-3100 FAX: (+82-31)636-3957...
- Page 11 Φ Use this welding power source at or under the rated duty cycle Exceeding the rated duty cycle limitation may result in damage to the welding machine. • The duty cycle is the percentage of a ten minute period that a welding power source can be operated at a given output without causing overheating and damaging the unit.
- Page 15 2. Welding cables, the coverings of which are not capable of withstanding a conductor temperature of 85 , will be damaged if the coupling devices are used at the rating given above at an ambient air temperature of 40 .
- Page 16 Connection observes and handle wiring in below. 1) Connect the power cable for base metal between the "Base metal (-)" terminal and the base metal. 2) Attach the power cable for wire feeder to the "Wire feeder (+)" output terminal. 3) Insert the control cable for wire feeder into the socket for wire feeder.
- Page 18 Φ...
- Page 19 • Connecting Input Power must meet all National and Local Codes - have only qualified persons make this connecting. • Before connecting input power, See rating label on unit and check input voltage available at site.
- Page 21 TORCH SW DELAY 5s MAGNETIC SW POST GAS(0.2s) SOLENOID VALVE NO LOAD VOLTAGE DELAY VOLTAGE OUTPUT VOLTAGE (0.4s) SLOW DOWN WIRE FEEDER WELDING CURRENT WELDING CRATER STOPS AFTER FAN COOLING DELAY 3 min DETECT WELDING CURRENT 0.2s TORCH SW DELAY 5s MAGNETIC SW POST GAS(0.2s) SOLENOID VALVE...
- Page 26 TROUBLE CAUSE MEASUREMENT WHEN POWER 'ON', 1. POWER DOES NOT 1. CHECK INPUT VOLTAGE ON POWER LAMP, SUPPLY. MAGNETIC CONTACTOR. COOLING FAN DOES (3PHASE, 220V,380V,440V,415V) NOT WORK 2. POWER S/W IS BAD 2. CHECK POWER S/W, IF NOT GOOD, REPLACE IT WITH GOOD. 3.
- Page 27 TROUBLE CAUSE MEASUREMENT WHEN GAS S/W OR 1. NO GAS IN BOMBE 1. FILL UP GAS TORCH S/W IS 'ON', 2. VALVE OPENNING IS NOT 2. OPEN VALVE ENOUGH PRESSURE ENOUGH. WEAK. 3. GAS LEAKS. 3. REPAIR GAS PATHWAY. 4. GAS PATHWAY IS BLOCKED 4.
- Page 28 TROUBLE CAUSE MEASUREMENT 6. W/F MOTOR IS BAD 6. REPLACE MOTOR INCAPABLE OF 1. VR(VARIABLE RESISTOR) 1. REPLACE VR CONTROLLING WIRE VOLUNE ON W/F IS BAD FEEDING SPEED. 2. CONTROL CABLE IS BAD 2. REPAIR CABLE 3. PCB IS BAD 3.
- Page 29 TROUBLE CAUSE MEASUREMENT HEATING REGULATOR 1. AUX.TR IS BAD 1. VOLTAGE BETWEEN NO.81 & VOLTAGE IS NOT 82 OF AUX.TR IS NOT DETECTED DETECTED. 110VAC, REPLACE AUX.TR 2. FUSE(F3) IS BROKEN 2. REPLACE FUSE(250V, 3A) BLOW HOLE OCCURS. 1. GAS IS NOT OUT 1.
- Page 35 220V 결선도 440V 결선도 220V 결선도 440V 결선도 220V 결선도 440V 결선도 380V 결선도 380V 결선도 380V 결선도...
Need help?
Do you have a question about the HiEGW 600W and is the answer not in the manual?
Questions and answers