Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
ZUS
Wireless Smart Backup Camera
170-Degree Rear View with No Wiring or Drilling Needed
User Manual
& Warranty
P1
2
3
4
6
12
12
12
12
13
15
Advertisement
Table of Contents
Related Manuals for Nonda ZUS
Summary of Contents for Nonda ZUS
-
Page 1: Table Of Contents
Wireless Smart Backup Camera 170-Degree Rear View with No Wiring or Drilling Needed User Manual & Warranty Quick Start Introduction Getting Started Installation Specifications App Features & Guide Important Safety Instructions Compatibility Warranty Regulatory Compliance... -
Page 2: Quick Start
Quick Start Camera Infrared Night Vision charging and wireless connection status Screw Battery Easy Installation 18650... -
Page 3: Introduction
Introduction The ZUS Wireless Smart Backup Camera is easy to install and built to fit your license plate. Install in just 10 minutes and get 170-degree field of view right on your smartphone. At a Glance M6 Locking Nut x 2... -
Page 4: Getting Started
Getting Started Charge the Device Connect the charging cord to the The front LED will turn RED when Backup Camera. Then, plug the charging. charging cord into a USB car charger or your car's built-in USB port. GREEN Once the battery is fully charged, the Disconnect the charging cable. - Page 5 Search for “ZUS” on the Apple App Store or Google Play. After downloading the app to your mobile phone, open the ZUS app and click on “add a Smart Backup Camera”. Long press 3 seconds Long press the button for 3 seconds to activate the camera.
-
Page 6: Installation
Installation 1. Standard Installation Unscrew the bottom two screws from your license plate. - Page 7 Align the top two holes of the mounting plate to the bottom two holes of your license plate. Screw on the M6 long screws and tighten them with the provided hex wrench. Place your ZUS Smart Backup Camera on the mounting plate and tighten the screws at both ends.
- Page 8 M6 Self-taping Screw for drilling purposes. Continue the rest of the installation process as described in the Standard Installation. Place your ZUS Smart Backup Camera on the mounting plate and tighten the screws at both ends.
- Page 9 3. Non-standard Installation Scenario 2 If your car does not have these two screw holes and you are NOT willing to drill holes on your car, please do the following. Take off your license plate. Place the provided hex nuts at the back of the license plate.
- Page 10 Insert the rubber underneath the license plate. Place your ZUS Smart Backup Camera on the mounting plate and tighten the screws at the both ends.
- Page 11 Troubleshooting Procedures If you cannot connect the device on the ZUS App, please follow check in the following sequence for troubleshooting. 1. Have you turned on your mobile’s bluetooth? 2. Have you turned on your mobile’s wi-fi? 3. Have you been connected to the correct wi-fi: ZUS_BACKUP_CAM? If the above troubleshooting procedures don’t work, please contact our...
-
Page 12: Specifications
Specifications Features Specifications Size 1.29 x 10.74 x 1.14 in / 33 x 273 x 29 mm 8.48 oz / 240.4 g Weight 2x 18650 (2400mAh) Batteries Camera Panasonic 34120，16M Lens 170 HD wide-angle lens Bluetooth Bluetooth 4.0 Operating Temperature -40 -60C (TBD) Storage Temperature -40 - 80 C... -
Page 13: Warranty
If a hardware defect in the Product arises and a valid claim is received within the Warranty Period, nonda will, at its sole option and subject to applicable laws: (a) repair the Product at no charge with a new or refurbished component or (b) replace the Product with a new or refurbished Product upon return of the defective Product. - Page 14 By sending the Device, consumer agrees to transfer ownership to nonda. nonda may not return the original device to consumer. If the claim is justified based on this Warranty, nonda shall bear the cost of shipping the repaired or replacement device to the Consumer.
-
Page 15: Regulatory Compliance
Regulatory Compliance FCC Compliance Statement FCC ID: 2AFZB-ZUMABKSAV NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. - Page 16 NCC Statement Administrative Regulations on Low Power Radio Waves Radiated Devices warning: Article 12 Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices.
- Page 17 Developed by nonda in California. Assembled in China. No NDA Inc., 320 Mountain View Avenue, Mountain View, CA 94041, USA. No NDA Inc., Günther-Wagner-Allee 13, 30177 Hannover, Germany. www.nonda.co | TM and © 2017 No NDA Inc. All rights reserved.