Table of Contents
Advertisement
Quick Links
INSTRUCTIONS FOR
160L 230V
Cement Mixer
Stock No.17776
Part No.CM170
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS PRODUCT.
GENERAL INFORMATION
These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools policy
of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper CM170
Summary of Contents for Draper CM170
- Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS 2.1 CONTENTS Page content Page TITLE PAGE INTRODUCTION ....................2 REVISION HISTORY................... 2 UNDERSTANDING THIS MANUAL ..............2 COPYRIGHT NOTICE ..................2 CONTENTS CONTENTS ......................3 GUARANTEE GUARANTEE ..................... 4 INTRODUCTION SCOPE........................ 5 SPECIFICATION ....................5 HANDLING & STORAGE ................... 5 HEALTH &... -
Page 4: Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period. -
Page 5: Introduction
4.1 SCOPE Professional standard electric concrete mixer for small to medium building projects. Light and portable and offering a good working height. 4.2 SPECIFICATION Stock no..........................17776 Part no........................... CM170 Voltage ........................230V~50Hz Drum capacity........................160L Drum opening ........................ 390mm DrumSpeed ........................30rpm Sound level ....................... -
Page 6: Health & Safety Information
IMPORTANT: Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you. - Page 7 HEALTH & SAFETY INFORMATION 20. CHECK DAMAGED PARTS: Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and any other conditions that may affect its operation.
-
Page 8: Caution: Risk Of Electric Shock. Do Not Open
HEALTH & SAFETY INFORMATION 5.5 CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. Caution: Risk of electric shock. Do not open. This appliance is supplied with a moulded 3 pin mains plug for your safety. The value of the fuse fitted is marked on the pin face of the plug. -
Page 9: Technical Description
TECHNICAL DESCRIPTION 6.1 IDENTIFICATION Back support Support legs Front support Wheels Mixing blades Drive gear shield Mixing drum Tilt bracket Handles Safety pin Panel board Mains lead Motor housing Switch ON/OFF... -
Page 10: Unpacking & Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Helpline (the telephone number appears on the Title page) and do not attempt to use the tool. -
Page 11: Preparing The Cement Mixer
PREPARING THE CEMENT MIXER NOTE: Remove the plug from the socket before carrying out adjustment, servicing or maintenance. 8.1 STAND - FIGS. 1-3 Sort the 4 support legs into two pairs with matching drill holes. Attach one pair of legs to the fixing tube on opposite sides, fix with the M8 x100mm bolts, then fix remaining legs. -
Page 12: Assembly Of Drum
PREPARING THE CEMENT MIXER 8.3 ASSEMBLY OF DRUM - FIGS. 5-7 Install the mixer blades to the base of the lower drum with the M8 x 35mm bolt, nut and washer FIG.5 Install rubber seal, then connect both halves of drum together using 8x round head M8 x 15mm bolts, nuts and washers FIG.6 Attach the mixing blades to the front of the... -
Page 13: Assembly Of Frame
PREPARING THE CEMENT MIXER 8.4 ASSEMBLY OF FRAME - FIGS. 8-10 Bolt the front and back frames together with 2x M8 x 75mm bolts and nuts FIG.8 Attach the panel board to the front support with 4x M8 x 70mm bolts and nuts. FIG.9 Install the shield to the panel board using 2x M8 x... -
Page 14: Installing Motor
PREPARING THE CEMENT MIXER 8.6 INSTALLING MOTOR - FIG. 12-13 Attach motor to the support using 3x M8x20mm bolts with nuts. Two bolts one either side of the drive shaft. FIG.12 The third bolt as seen from beneath. FIG.13 8.7 INSTALLING WHEELS - FIG. 14 Attach wheels with bolts 2x M8x15mm and washers. -
Page 15: Attach Tilt Bracket
PREPARING THE CEMENT MIXER 8.8 ATTACH TILT BRACKET - FIG. 15 FIG.15 Remove the tilt bracket from the stand and offer it up to the axle bracket on the cement mixer. Connect with pivot pins , then slide split pins through to secure in place. -
Page 16: Attach Stand And Raise
PREPARING THE CEMENT MIXER 8.10 ATTACH STAND AND RAISE FIG.18 - FIGS. 18 - 21 NOTE: The tilt mechanism needs to be locked in position with the chained safety pin before attempting to lift the cement mixer. Tip the cement mixer over onto it’s face. (ii) Attach the support legs into the tilt bracket... -
Page 17: Operating Instructions
OPERATING INSTRUCTIONS 9.1 HOW TO USE To switch ON push the green button, to switch OFF push the red button. See ‘Electrical Safety’ for more details of the switch. The most important thing to remember when using the mixer is that the drum must be rotating BEFORE loading and should continue to rotate until unloaded. -
Page 18: Explanation Of Symbols
10. EXPLANATION OF SYMBOLS 10.1 EXPLANATION OF SYMBOLS WEEE Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish Warning! Wear goggles. Warning! Wear dust mask. Class II construction (Double insulated). Warning! Read instruction manuals before operating and servicing this equipment. -
Page 19: Disposal
11. DISPOSAL 11.1 DISPOSAL - At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. - Contact your local authority for details of collection schemes in your area. In all circumstances: •... - Page 20 - Sales Desk: (023) 8049 4333 - General Enquiries: (023) 8026 6355 - Service/Warranty Repair Agent For aftersales servicing or warranty repairs, please contact the Draper Tools Helpline for details of an agent in your local area. YOUR DRAPER STOCKIST KCMC0716...
Need help?
Do you have a question about the CM170 and is the answer not in the manual?
Questions and answers