Download Print this page
Kyosho INFERNO MP777 Instruction Manual
Kyosho INFERNO MP777 Instruction Manual

Kyosho INFERNO MP777 Instruction Manual

1:8 scale rc racing buggy
Hide thumbs Also See for INFERNO MP777:

Advertisement

Before beginning assembly, please read these instructions thoroughly.
INSTRUCTION MANUAL
インファーノ MP777
1:8
INFERNO MP777
RADIO PREPARATION
BEFORE YOU BEGIN
ASSEMBLY
EXPLODED VIEW
-
!
.
,
*
© 2004 KYOSHO CORPORATION/禁無断転
,
.21 ;
REQUIRED FOR OPERATION
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS
OPERATING YOUR MODEL SAFELY
SPARE PARTS & OPTIONAL PARTS
ンパーツリスト
,
.
. *SPECIFICATIONS ARE SUBJECT TO BE CHANGED WITHOUT NOTICE.
© 2004-2007, HobbyCenter.Ru
,
UNDER SAFETY PRECAUTIONS
!
This radio control model is not a toy!
●First-time builders should seek the advice of experienced modellers before
beginning assembly and if they do not fully understand any part of the
construction.
●Assemble this kit only in places out of children's reach!
●Take enough safety precautions prior to operating this model.
!
 You are responsible for this model's assembly and safe operation!
●Always keep this instruction manual ready at hand for quick
 reference, even after completing the assembly.
.
.
R
THE FINEST RADIO CONTROL MODELS
.
.
目 次 INDEX
2 ~ 3
3
4
5 ~ 6
7 ~ 26
27
28 ~ 30
31 ~ 34
No. 31777

Advertisement

loading
Need help?

Need help?

Do you have a question about the INFERNO MP777 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Kyosho INFERNO MP777

  • Page 1  You are responsible for this model's assembly and safe operation! ●Always keep this instruction manual ready at hand for quick  reference, even after completing the assembly. No. 31777 . *SPECIFICATIONS ARE SUBJECT TO BE CHANGED WITHOUT NOTICE. © 2004-2007, HobbyCenter.Ru © 2004 KYOSHO CORPORATION/禁無断転...
  • Page 2 Paint ■ー    Plug Heater Glow Fuel プ Kyosho,  Fuel Pump ●For painting the body, use Kyosho paints for models! B P M o d e F u e l E n g i n e ニト ロ No.2230 No.73403 No.96422...
  • Page 3 Sharp Hobby Rubber Cement ゴム系接着剤 TOOLS INCLUDED ■   Instant Glue Hex Wrench (1.5mm, 2mm, 2.5mm, 3mm) Box Wrench KYOSHOー KYOSHO Special Glue No.96154 Grease No.1829 Grease No.695101 KNIFE EDGE REAMER ROUND CUTTER & SANDER Cross Wrench No need to pre-drill!
  • Page 4 (2)2) BEFORE YOU BEGIN (2) 1:1, This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. 種類...
  • Page 5 ARRANGEMENT OF PLASTIC PARTS ON RUNNERS (1) ランナー付 プラパーツ配置図 (1) No.1 Shaded parts are not used. No.4 Use the parts within the dotted lines as tunning options. Shaded parts are not used. No.5 裏面 Reverse 裏面 Reverse © 2004-2007, HobbyCenter.Ru...
  • Page 6 ARRANGEMENT OF PLASTIC PARTS ON RUNNERS (2) No.5 No.6 No.9 Shaded parts are not used. 159 160 © 2004-2007, HobbyCenter.Ru...
  • Page 7 フギヤ No.2 Gear Differential (For front and rear) 4x4mm 平らな面 Flat surface (For center) 4 x 4mm セットビス 4 2.6 x 14mm Set Screw Shaft (Black) 5 6mm 7 8 x 16mm ベアリング O-ring Ball Bearing For front and rear 10 4 x 10mm Shim For center...
  • Page 8 No.2, No.4, Rear Gearbox No.5, No.10 4 x 20mm TP F/H Screw 4x20mm 4 x 25mm TP F/H Screw 13 x 16mm Thick Thin) Shim 17 , 18 7 8 x 16mm ベアリング Ball Bearing 4x25mm 17 , 18 Adjust the backlash with the shims.
  • Page 9 No.5, No.10 3x15mm Wing Stay Note the types of screws ! 4x15mm 3x15mm 3 x 15mm TPビス TP Screw 4 x 15mm 4 x 20mm ス 4x20mm TP Screw Screw 4x15mm 4x20mm No.4, No.5 Ò R Ó marked. < > 右側用...
  • Page 10 No.5, Rear Suspension No.10 45 5 x 35mm Set Screw . 14.5mm approx. 14.5mm 44 7.8mm 43 7.8mm ボールエンド ボールエンド Ball End Ball End No.4, No.10 Rear Suspension ナイロンナット Nylon Nut 3x25mm 46 7.8mm ツバ付ボール Ball Note the direction. 3 x 25mm Cap Screw 取付穴...
  • Page 11 No.9, No.10 Chassis 4 x 20mm TP F/H Screw 4x20mm 4x20mm No.4, No.9, Chassis 3x18mm No.10 3 x 10mm F/H Screw 3 x 18mm キャップビス Cap Screw Long Torque Rod Ball 55 6.8mm Ball End (L) 56 6.8mm Ball 3x10mm Front Gearbox No.6, No.10 4x20mm(F/H)
  • Page 12 No.5, No.6, No.10 Front Gearbox 5 x 4mm Set Screw Tighten the set screw to the flat spot. 4 x 15mm TPサラビス 5x4mm TP F/H Screw 4 x 20mm TPサラビス TP F/H Screw 4x15mm ÒLÓを使用。 Use the "L" marked piece. 4x15mm "...
  • Page 13 No.5, No.6, No.10 Front Suspension For left side. For right side. 4x12mm E2.5 Left Note the direction. E2.5 4 x 12mm Right Set Screw 上 Note the direction. 74 3 x 38mm Shaft E2.5 E-ring (Silver) Bottom 下 For adjusting the ground clearance. 41 4 x 74mm シャフト...
  • Page 14 No.6 No.10 Front Suspension 3x10mm 3x15mm 3 x 3mm Set Screw 3x3mm 3 x 4mm Set Screw 3 x 10mm Set Screw 3x3mm 3 x 15mm ビス Screw 2.6 x 5mm F/H Screw 5.8mm Ball 48 5.8mm 3x4mm Ball End (S) 2.5mm Diameter 2.5mm 2.6x5mm...
  • Page 15 Center Gearbox No.8 . 7mm approx. 7mm Brake Caliper Brake Pad (Black) 12mm Center Differential Disk Plate Bolt (長い) (Long) Center Gearbox (短い) No.4, No.6, No.9, No.10 (Short) 4 x 15mm TP F/H Screw 3x8mm 3 x 8mm TP F/H Screw 3x8mm 4x15mm センターギヤボックス...
  • Page 16 No.7, No.10 Steering 4x10mm Note the direction. 4 x 10mm F/H Screw Steering Collar Flanged Nut 104 6 x 10mm Ball Bearing 3x10mm 4x10mm 3 x 10mm Steering Pin 3x10mm Washer 3x10mm 4x10mm No.7, No.10 105. Steering Remove these screws and retighten after installing 3 x 10mm...
  • Page 17 No.3 Engine Engine Assemble the following parts with pulling the crankshaft. Engine taper collet included in the kit. Tapered Coret The short side of must be in the groove of Pilot Nut 114. 115 3 x 5 x 0.2mm Shim No.3 Engine Engine...
  • Page 18 No.3, No.10 Engine Insert a sheet of paper before installing. Front 4 x 6mm 4x10mm F/H Screw 4x10mm 4 x 10mm Flanged Cap Screw 4x6mm 4x6mm No.9, No.10 Muffler 4 x 4mm Set Screw 3 x 6mm F/H Screw Manifold 4x4mm Muffler Bend so it fits into the muffler.
  • Page 19 3 x 15mm 3x15mm Fuel Tank TP Screw 3x15mm No.8, No.9, 3 x 10mm No.10 TP F/H Screw O-ring P3 132 - Cut the Silicone Tube, depending on Engine and Muffler. 3x10mm Note the direction for O-ring. Note the types of screws ! 2x8mm 2x8mm 2x20mm...
  • Page 20 No.9, No.10 Radio Hook Pin Receiver Antenna Better to fill some sponge between radio box and receiver as well as battery. Battery No.10 Radio 3 x 12mm TP F/H Screw 3x12mm 3x12mm Part bags used. Must be purchased separately! © 2004-2007, HobbyCenter.Ru...
  • Page 21 No.9, No.10 Radio 3x12mm 3x12mm 3x10mm 3x15mm 3x10mm Steering Servo Throttle Servo (For transponder.) Note the types of screws ! 3 x 10mm Cords 3 x 15mm TP F/H Screw TP Screw 3 x 12mm 3 x 10mm Screw TP Screw Connect as per radio.
  • Page 22 2.6mm 150 151. Servo Horn Radio Note the directions of 2x6mm No.7, No.9, No.10 2.6x6x1mm Adjust the height with 2.6x6x1mm collar. NOVA Rossi: 2.6x6x2mm .約19mm With O.S. and NOVA Rossi engines : Adjust the height with 2.6x6x2mm collar. approx. 19mm 2.6x6x3mm Picco: Adjust the height with 2.6x6x3mm collar.
  • Page 23 Engine Rainy Weather No.3, No.10 After putting the cover on, loosen the screw, fit in the plastic washer and screw in the 3 x 10mm screw again. TP F/H Screw Soak inner sponge with oil. No.1948 Air Cleaner Oil 3x10mm 3x15mm 3x10mm Fuel Filter...
  • Page 24 Shock Oil Shock No.1 Fill in until shock oil nearly overflows. Check if piston moves smoothly. Then, gently move the piston up and down to get rid of air bubbles. Pull down the piston. )– No.1 (Short) — For Front Shock )–...
  • Page 25 Clean the tire rims with thinner beforehand. Wheels Apply instant glue little by little in the below order. Slide the tires into these slots in the wheels. Apply rubber cement and install in tires. No.4, No.6, No.10 Wheels < > <...
  • Page 26 Kyosho. Paint the body shell from the inside using Kyosho’s spray colors. Apply decals to any spots you like. Decals Cut off shaded portion. Drill holes with the specified diameter.
  • Page 27 意 OPERATING YOUR MODEL SAFELY 取扱いの注 WARNING: Do NOT operate the model in the following places and situations: (Non-observance may lead to accidents!) Always check the dry batteries in the radio! When the dry batteries get weaker, transmission and reception of the radio decrease.
  • Page 28: Exploded View

    IF308 Rear Shoch 92213 W0142 IF309 IFW140-07 W0141V IF115 W0142 IF306 IF325 W0141V W0202 IF137B IF137B 1296 IF137B IF325 IF325 IF318 92831 92511 1296 IFH001W Front Shoch IF116 IF318 92511 © 2004 KYOSHO CORPORATION / INFERNO MP777 © 2004-2007, HobbyCenter.Ru...
  • Page 29 < > EXPLODED VIEW ( 1 ) デフギヤ Gear Differential IF102 IF39 IF39 ORG06 IF101 ORG06 IF102 BRG0120 BRG0120 IF102 IF103 IF106 BS107 < フロント/リヤ > IF102 < Front / Rear > IF101 IF102 IF39 IF39 ORG06 IF104 ORG06 IF102 BRG0120 IF102 BRG0120...
  • Page 30 < > EXPLODED VIEW ( 1 ) < > Gear Differential IF102 IF39 IF39 ORG06 IF101 ORG06 IF102 BRG0120 BRG0120 IF102 IF103 IF106 BS107 < > IF102 < Front / Rear > IF101 IF102 IF39 IF39 ORG06 IF104 ORG06 IF102 BRG0120 IF102 BRG0120...
  • Page 31 SPARE PARTS ★ FOR JAPANESE MARKET ONLY. 品番 発送 品番 発送 ★定価 ★定価 ★ ★ Part Names Quantity Part Names Quantity (税込) 手数料 (税込) 手数料 ト 90 x 2 57 x 1 55 x 2 BS45 IF118 Front Center Shaft 一律...
  • Page 32 SPARE PARTS ペツ ★ FOR JAPANESE MARKET ONLY. 品番 ★定価 発送 品番 ★定価 発送 ★ ★ Part Names Quantity Part Names Quantity (税込) 手数料 (税込) 手数料 (MP777 ー 128 129 135 136 137 111 x 10 IF325 1050 W0141V Receiver Box Set (MP777) 3mm Tapered Washer 140 146 170 一律...
  • Page 33 OPTIONAL PARTS オ プションパーツ ★ FOR JAPANESE MARKET ONLY. 品番 内 ) 発送 品番 内 ) 発送 ★定価 ★定価 ★ ★ Part Names Quantity Part Names Quantity (税込) 手数料 (税込) 手数料 BSW71 と交換 .201 202 1890 1050 IFW304 Color Nylon Wing (Blue) SP Steering Plate 201 202 instead of...
  • Page 34 SCREW・NUT etc. ビス・ナット類 ● FOR JAPANESE MARKET ONLY. 品番 (mm) 品番 (mm) 品番 径 Size (mm) QUANTITY Size (mm) QUANTITY QUANTITY ★210 ★210 ★210 Round Head Screw (税込) (税込) (税込) Round Head Self-Tapping Screw 1101 2x6・2x8・2x10・2x15 5 each 1132 2x4・2x6・2x8・2x10 5 each 1171 2mm・2.6mm...