1. Manuals
  2. Brands
  3. Iqua Manuals
  4. Automobile Accessories
  5. Snake II
  6. Product specification

Iqua Snake II Product Specification

Headrest handsfree
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Headrest Handsfree

Product Specification

Change history
Version
Date
0.1
07.07.2005
0.2
7.9.2005
0.3
17.10.2005
0.4
25.11.2005
Iqua
"Snake II"
Version 0.4
Modified by
RZh
Document started
Valter Rönnholm
Keypress length for entering Pairing-mode
changed from "5 seconds" to "3 seconds" (in
order to avoid confusing behaviour e.g. when
pressing for 4 seconds).
"Voice dial activation" changed from "2s press"
to "short press" (in order to differentiate from
"power off" 3s).
Pairing PIN code changed from "1234" to "0000".
Bluetooth name changed from "Iqua Snake II" to
"Iqua Snake 2".
Valter Rönnholm
Resetting functionality removed altogether (as
agreed on 13.10.
huangzhiming
The battery type is Li-Polymer battery and the
fully charged time.
Comment

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Snake II and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Iqua Snake II

Summary of Contents for Iqua Snake II

  • Page 1: Product Specification

    “Voice dial activation” changed from “2s press” to “short press” (in order to differentiate from “power off” 3s). Pairing PIN code changed from “1234” to “0000”. Bluetooth name changed from “Iqua Snake II” to “Iqua Snake 2”. 17.10.2005 Valter Rönnholm Resetting functionality removed altogether (as agreed on 13.10.
  • Page 2 Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

  • Page 3: Product Introduction

    Snake II’s neck part has a flexible mechanism, which make it possible to adjust it to user’s height. The neck-part is bendable upwards by 90 degrees and downwards by 90 degrees.

  • Page 4: User Interface

    There are two LEDs (Red and Blue) with light guide to indicate different operational states. LEDs can light continuously or blink/flash. User controls operations of Snake II with two Push Buttons by pressing them one at a time or both at the same time with different durations. The two push buttons are located on the upside of Snake.

  • Page 5: Battery Charging

    During pairing, the LED flashing continues for approximately 10 minutes or until the Snake II is connected to a compatible phone. If the Snake II can not be connected to the phone during this time, it beeps shortly three times with red LED blinks then the device is switched off automatically.

  • Page 6: Reject Incoming Call

    Switch Between Handsfree and Phone mode You can transfer calls between the Snake II and mobile phone. 1. To transfer an active call from Snake II to the mobile phone, press and hold the POWER/CALL -button for 3 seconds. 2. To transfer an active call from your mobile phone to Snake, press shortly the POWER/CALL -button.

  • Page 7: Indicator Lights

    • Pairing state – blue/red light flashing alternatively, the flashing continues for approximately 10 minutes or until the headset is connected to a compatible phone. If the Snake II can not be connected to the phone during this time it is automatically switched off.
  • Page 8 Hinge joint Attachment fixture & screws: (fastening even with coin) Charging plug Personal Earpiece jack...

Table of Contents