Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Technical Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Anyload OCS Series
Summary of Contents for Anyload OCS Series
- Page 1 OCS Series Electronic Crane Scale User’s Guide OCSA3 & OCSA4 General Purpose Crane Scales OCSB3 & OCSB4 Compact Crane Scales OCSC3 & OCSC4 Enhanced Crane Scales OCSG1 & OCSG2 Heat Resistant Crane Scales OCSZ Heavy Duty Crane Scale...
-
Page 3: Table Of Contents
View Total Mode Idle Mode 2ND Mode Password Mode Total View Total Delete Last Total Clear Total Display Unit Switch Tare Set Resolution Switch Battery Check System Setup Resolution Auto Power-Off Timing Idle Timing ANYLOAD OCS Series Electronic Crane Scale User’s Guide... - Page 4 Display Brightness Display Frequency Anti-Motion Level Communication Setup Communication On/Off Baud Rate Scale Address Output Mode 7. Battery 8. Messages Illustration 9. Troubleshooting 10. Notes ANYLOAD OCS Series Electronic Crane Scale User’s Guide...
-
Page 5: Safety Guides
Easy to Use. Ultra‐red remote controlling design. Easy to operate on the scale or in distance. Complete Function. Division switch, unit conversion, automatic power saver, battery inspection, idle mode, tare set, etc. ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 6: Specifications
Scale will go through power‐on test, battery check and initialization. Condition Power‐on test is progressing when display flashes the following characters twice. If scale doesn’t pass the test, error message will display. ANYLOAD OCS Series Electronic Crane Scale User’s Guide... - Page 7 A UTO ‐Z ERO function is enabled. To learn more about Auto‐Zero function refer to Auto‐Zero Range in Scale’s Configuration function. After the scale is completely powered up and initialized, it is ready for weighing operations. ANYLOAD OCS Series Electronic Crane Scale User’s Guide...
-
Page 8: Zero
(when the scale is in G ROSS M ODE ). Function The scale will store the tare weight and will shift to N ET M ODE . All subsequent readings are deviated from the tare value. ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 9: Tare Out
Action To T ARE O UT the tared weight from the scale, press TARE key on on remote controller ( the scale shall be in N ET scale or M ODE ). ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 10: Hold
The scale will show the current weight reading. Condition To H OLD the scale, it must be stabled otherwise an error message will display NOTE: Scale can be unlocked anytime in HOLD mode. ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 11: Power Off
In this section, the user will learn how to operate the scale in a convenient and proper way either on scale or by its remote controller. Detailed operations are described in Quick Start section and Advanced Operation section. 10 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 12: Keys On Scale
Hold Wake Up Confirm Confirm Confirm Setup Resolution ↓ ↓ ↓ Total Wake Up Switch Clear ← ← ← Clear Wake Up Total Last Battery View Wake Up Check Total 11 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 13: Input Numerals
Most of the operations are accessible and be done via the dedicated remote controller. Some of the settings of the scale require password. Contact your local representatives or technical support for password the information 12 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 14: Scale's Mode
In G ROSS M ODE , the TARE indicator w i l l light off. The default weight reading is in G ROSS M ODE. NOTE: In Net Mode, Zero function is disabled 13 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 15: View Total Mode
To learn more about View Total, refer to View Total in Advanced Operations section. NOTE: Other functions are disabled in View Total Mode IDLE MODE Action No buttons or keys are required to enter the I DLE M ODE . 14 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 16: 2Nd Mode
To access the functions that are not shown in the remote controller, press this 2ND key. In 2 ND M ODE , pressing the 2ND key will show the message below and keep flashing until the user’s input key is entered. 15 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 17: Password Mode
Function Current weight reading will be accumulated into scale’s T OTAL accumulated weights. The screen will display the below message indicating that T OTAL is successfully calculated, added and saved. 16 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 18: View Total
The scale must not in H OLD mode otherwise an error message will display . The T OTAL must be greater than 0 (or 0.0 or 0.00, depending on the resolution) otherwise an error message will display. 17 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 19: Delete Last Total
The Last Total must be greater than 0 (or 0.0 or 0.00, depending on the resolution) or has not been deleted otherwise an error message will display. CLEAR Action To clear the overall Total, press and then on remote controller. 18 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 20: Display Unit Switch
(metric system), lb (imperial system) and U SER ‐ DEFINED U NIT . The screen flashes the unit to change and returns to W EIGHING M ODE 19 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... - Page 21 It will return to its default SYSYTEM UNIT set during calibration. In changing the SYSTEM unit, recalibration of the scale is required. Refer more to Technical Manual in changing SYSTEM UNIT and recalibration. 20 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide...
-
Page 22: Tare Set
The scale must be in G ROSS M ODE otherwise an error message will display The input tare weight must be greater than 0 (or 0.0 or 0.00, depending on the resolution) otherwise an error message will display 21 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 23: Resolution Switch
To balance between accuracy and measurement speed in high resolution mode, the A NTI ‐M OTION L EVEL can be changed to fit your measurement application. 22 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 24: Battery Check
System checks the battery and feedbacks with battery’s left charge. The screen flashes the battery charge in voltage like the image below. Please refer to Battery section for more information about battery. 23 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 25: System Setup
In S YSTEM S ETUP M ODE , user can change the scale’s system function to their desired setting like higher resolution, automatic power‐off delay, idle delay, the screen’s brightness, display frequency, anti-motion level, etc. The screen will display the welcome message shown below: 24 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 26: Resolution
“never”. When A UTO P OWER ‐O FF T IMING is set to “00” the scale is set to “never” meaning auto-off is disabled. The default A UTO P OWER ‐O FF T IMING is set to “15” minutes. 25 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 27: Idle Timing
D ISPLAY F REQUENCY sets the speed of the screen updates when the weight reading changes. There are 5 levels of Display Frequency, “0” to “4”. At level 4, the screen’s update rate changes slower while at level 0 it changes faster. 26 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 28: Anti-Motion Level
To confirm inputted value, press HOLD key on scale or on remote controller. To save and exit C OMMUNICATION S ETUP M ODE , press 2ND key on scale for on remote controller. 27 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 29: Communication On/Off
B AUD R ATE is the speed that scale outputs signal. There are 4 option baud rates: 1200bps, 2400bps, 4800bps, and 9600bps. By default, B AUD R ATE is set to 1200bps. 28 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 30: Scale Address
The default O UTPUT M ODE is set to “0” continuous way. To learn more about serial communication protocol, refer to Technical Manual 29 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 31: Battery
To obtain maximum service from your batteries, it should be stored between ‐20°C (‐4°F) and +50°C (122°F). Stored batteries should be recharged every three months. Battery is fully charged when the charging indicator status turned to red. 30 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 32: Messages Illustration
The scale is tared (in net mode). The resolution is 5 kg or lb. system setup SYSTEM SETUP welcome message auto power off AUTO POWER‐OFF TIMING idle IDLE TIMING brightness DISPLAY BRIGHTNESS display DISPLAY FREQUENCY 31 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 33: Troubleshooting
Battery cannot be Defective battery Replace the battery recharged Defective charging plug Replace the charging plug Short remote controlling Replace remote controller Remote controller distance batteries batteries may require replacement 32 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... -
Page 34: 10. Notes
10. Notes 33 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide... - Page 36 ANYLOAD Weigh & Measure Inc. Website: www.anyload.com Email: info@anyload.com Fax: +1 866 612 9088 North America Toll Free: 1-855-ANYLOAD (269 5623)
Need help?
Do you have a question about the OCS Series and is the answer not in the manual?
Questions and answers