Related Manuals for Cambridge Elevating Elmira
Summary of Contents for Cambridge Elevating Elmira
- Page 1 Residential Elevator Design Guide All Models - Elmira, Heritage & Cambrian 1261 Industrial Rd • Cambridge, ON • N3H 4W3 • (p) 1.800.265.3579 • (p) 519.653.4222 • (fl 519.653.9927 www.CambridgeElevating.com...
-
Page 2: Table Of Contents
Machine Room Details – Controller / Pump Details Cambrian Landing Frame Details - Elevation Cambrian Landing Frame Details - Layout Drawings - Elmira Model Cab/Hoistway Size Layout 14-15 Drawings - Heritage Model Cab/Hoistway Size Layout Drawings - Cambrian Model Cab/Hoistway Size Layout Elevator Specifications for ASME A17.1 Part V Compliance... -
Page 3: Introduction
1. Determine the customer’s intended use. 2. Determine the customer’s desired convenience level with respect to model type: Elmira – swing landing door with manual (or automatic) accordion cab gate Heritage – swing landing door with automatic sliding cab door panels ... -
Page 4: Provisions By Others
Provisions By Others Provide one permanent 220/1/60 (30 amps) & one 110/1/60 (15 amps) power source to the designated machine room location. Both electrical disconnects are provided by the elevator manufacturer. Provide appropriate sleeves for both the electrical conduit and hydraulic line from the drive unit to the hoistway. -
Page 5: Description Of Elevator Equipment
Nominal speed: 40 feet per minute Fully automatic operation Elmira minimum pit depth: 8” Automatic timed cab lighting Elmira minimum overhead clearance: 96” Stainless steel car operating panel (COP), Heritage/Cambrian minimum pit depth: 12”... -
Page 6: Hoistway Construction - General Notes
Hoistway Construction – General Notes A load-bearing wall is required to sustain rail reactions; please see Rail Wall Construction – Wood Stud Wall (next page) for detail. Hoistway must be in accordance with ASME A17.1/CSA B44-13, AND all local codes and regulations. ... -
Page 7: Hoistway Construction - Wood Stud Wall
1261 INDUSTRIAL RD THIS DRAWING AND THE INFORMATION IT CONTAINS ARE PROPRIETARY TO ABILITY TO SUPPORT THE ELEVATOR CAMBRIDGE ELEVATING INC. THIS DOCUMENT MUST NOT BE DUPLICATED, CAMBRIDGE, ONTARIO OR ITS CONTENTS USED OR DISCLOSED (IN WHOLE OR IN PART) WITHOUT LOADS AND/OR REACTIONS THE WRITTEN PERMISSION FROM CAMBRIDGE ELEVATING INC. -
Page 9: Pit Details
STANDARDS AND CODES 1261 INDUSTRIAL RD THIS DRAWING AND THE INFORMATION IT CONTAINS ARE PROPRIETARY TO CAMBRIDGE ELEVATING INC. THIS DOCUMENT MUST NOT BE DUPLICATED, CAMBRIDGE, ONTARIO OR ITS CONTENTS USED OR DISCLOSED (IN WHOLE OR IN PART) WITHOUT THE WRITTEN PERMISSION FROM CAMBRIDGE ELEVATING INC. -
Page 10: Machine Room Details - General Layout
Machine Room Details – General Layout Machine room must be in accordance with all codes and regulations. A 220 VAC, 60 Hz, 30 Amp single phase power source in the machine room to be provided. A 115 VAC, 60 Hz, 15 Amp single phase power source in the machine room to be provided. ... -
Page 11: Machine Room Details - Controller / Pump Details
13" 1261 INDUSTRIAL RD THIS DRAWING AND THE INFORMATION IT CONTAINS ARE PROPRIETARY TO CAMBRIDGE ELEVATING INC. THIS DOCUMENT MUST NOT BE DUPLICATED, CAMBRIDGE, ONTARIO OR ITS CONTENTS USED OR DISCLOSED (IN WHOLE OR IN PART) WITHOUT THE WRITTEN PERMISSION FROM CAMBRIDGE ELEVATING INC. -
Page 12: Cambrian Landing Frame Details - Elevation
Cambrian Landing Frame Details – Elevation It is the recommendation of Cambridge Elevating to leave door walls wide open for installation. Landing door jambs and header fit within rough stud opening. Landing door operating mechanism, door frames and sill hang in hoistway attached to inside wall of hoistway using brackets. -
Page 13: Cambrian Landing Frame Details - Layout
Cambrian Landing Frame Details – Layout It is the recommendation of Cambridge Elevating to leave door walls wide open for installation. www.CambridgeElevating.com August 2017... -
Page 14: Drawings - Elmira Model Cab/Hoistway Size Layout
Elmira Model Cab / Hoistway Size Layout Cab Size Hoistway Size Centerlines Landing Rail Width x Depth Door Wall 36” x 48” 54” x 54.25” 31” 26.75” 36” x 54” 54” x 60.25” 31” 28.25” 36” x 60” 54” x 66.25”... - Page 15 Elmira Model Cab / Hoistway Size Layout Cab Size Hoistway Size Centerlines Rail Landing Wall Width x Depth Door 44” x 42” 54” x 56.25” 31” 27” 48” x 42” 58” x 56.25” 35” 29” 54” x 48” 64” x 62.25”...
-
Page 16: Drawings - Heritage Model Cab/Hoistway Size Layout
Heritage Model Cab / Hoistway Size Layout Cab Size Hoistway Size Centerlines Landing Rail Width x Depth Door Wall 44” x 48” 62” x 57.75” 38.75” 27.75” (2 panel doors) 36” x 48” 54” x 56.875” 32.75” 28.0625” (3 panel doors) 36”... -
Page 17: Drawings - Cambrian Model Cab/Hoistway Size Layout
Cambrian Model Cab / Hoistway Size Layout Cab Size Hoistway Size Centerlines Landing Rail Width x Depth Door Wall 44” x 48” 62” x 61.75” 38.75” 31.75” (2 panel doors) 36” x 48” 54” x 63.25” 32.75” 33” (3 panel doors) 36”... -
Page 18: Elevator Specifications For Asme A17.1 Part V Compliance
2.3.1 General Contractor to provide one 220 VAC, 60 Hz, 30 Amp single phase power source in the machine room. 230 VAC disconnect provided by Cambridge Elevating. 2.3.2 General Contractor to provide one 120VAC, 60 Hz, 15 Amp power source and disconnect in the machine room. 120 VAC disconnect provided by Cambridge Elevating. www.CambridgeElevating.com August 2017... - Page 19 Approval drawings shall show a complete layout of elevator equipment, including plan and elevation views. PART 4 – PRODUCT 4.1 Equipment Manufacturer The elevator shall be manufactured by Cambridge Elevating Inc. 4.2 Components The elevator will have the following components. 4.2.1 Cab 4.2.1.1 Car sizes (please visit our full drawings pages at (http://cambridgeelevating.com/tools)
- Page 20 4.2.1.5 Hand Rail Brushed stainless steel handrail mounted to cab wall (shipped loose in unfinished cabs) in solid flat bar or cylindrical. (Standard handrail is 36” x 1½” straight ends, flat) 4.2.2 Hydraulic Power Unit and Motor Power unit to consist of 20 U.S. gallon enclosed metal tank, 4.0hp or 5.0hp submersible induction motor and pump.
- Page 21 4.2.9 Safety Devices The elevator will have the following safety devices: 4.2.9.1 208/230 VAC lockable disconnect for power unit 4.2.9.2 Final limit 4.2.9.3 Slack rope safety switch 4.2.9.4 Pit stop switch 4.2.9.5 Car top stop switch 4.2.9.6 Line rupture valve 4.2.9.7 Low pressure switch 4.2.9.8 Automatic re-leveling 4.2.9.9 Emergency battery lowering...