Related Manuals for Kurt MX350 MaxLock
Summary of Contents for Kurt MX350 MaxLock
- Page 1 MX350 MaxLock Operating Instructions Manual Manual de instrucciones de operación ENGLISH...
-
Page 2: Table Of Contents
Table of Contents Introduction .........................3 Set-up Instructions ....................4-5 Operating Instructions ..................6-7 MX350 Drawings ....................8-9 MX350 Parts List....................10-11 MX350 Mechanical Drawing................11 Replacement of 5/8 - 11 Threaded Rod ............12 WARNING: Indicates a potential danger that requires correct action to avoid personal injury. -
Page 3: Introduction
Introduction Thank you for purchasing a Kurt vise. You have just purchased one of the best machine vises in the industry. Our new MX350 MaxLock 5-axis vise is a welcomed product in our industry. The outstanding accuracy of this product is second to none. Backed by a IRONCLAD lifetime warranty, this product will last a lifetime when used and maintained properly. -
Page 4: Set-Up Instructions
Set-up Instructions The MX350 will come packaged and assembled in a ready to use state. Check your list of parts with the items you have received with your MX350 5-axis vise. You should have items 1 thru 23. These are the items provided with the standard MX350 vise. - Page 5 Your new Kurt MX350 5-axis vise is ready for operation. Be sure to use caution when clamping your parts and DO NOT exceed the recommended maximum torque value of 40lbs of torque Fig.1 Fig.2 Set this distance at approximately 3/8 inch less than the thickness of your part.
-
Page 6: Operating Instructions
Operating Instructions For proper vise operation insert the handle on the hex end of the vise. Rotate clockwise to clamp and counterclockwise to unclamp your vise. This handle combined with the correct amount of torque will provide you with all the clamping force you will need to machine your parts. A high quality calibrated torque wrench can be used if needed. - Page 7 Fig.3 Fig.4 ENGLISH | Operating Instructions...
- Page 8 ENGLISH | MX350 Drawings...
-
Page 9: Mx350 Drawings
ENGLISH | MX350 Drawings... -
Page 10: Mx350 Parts List
MX350 Parts List ITEM# PART# DESCRIPTION QTY. MX350-1 T-SLOT BASE MX350-2 MOVABLE MX350-3 MX350-6 STATIONARY MX350-293 DRIVE, SCREW MX350-236 HARD JAW PLATE MX350-252 RETAINER, LOCKING MX350-5- 5/8-11 THREADED ROD MODIFIED MX350-248 CUSTOM CHIP GUARD MX350-42 THRUST WASHER MX350-41 THRUST BEARING MX350-97 THREAD SEAL WIPER MX350-211... -
Page 11: Mx350 Mechanical Drawing
D40-68 O-RING #024 D40XI-10-SA HANDLE ASSEMBLY MX350-111 KURT / 5 AXIS STICKER MX350-313R WEBSITE STICKER MX350-314F MAXLOCK STICKER 07-0230 DRIVE SCREW MX350-102 SERIAL TAG MX350-176 LOCATOR BOLT MX350 Mechanical Drawing ENGLISH | MX350 Mechanical Drawing... -
Page 12: Replacement Of 5/8 - 11 Threaded Rod
Replacement of 5/8 - 11 Threaded Rod When reassebling the hex drive (drive screw) to threaded rod, thread (2) 5/8 - 11 nuts onto the new threaded rod. 1/4 - 20 tapped hole should extend about 1 - 1/2” beyond nuts. Tighten jam nuts on threaded rod. - Page 13 Maintenance Log/Notes: ENGLISH | Maintenance Log/Notes...
- Page 14 Maintenance Log/Notes: ENGLISH | Maintenance Log/Notes...
- Page 15 Thank you for your purchase! If you have any feedback or questions. Please contact us at: workholding@kurt.com 1-877-226-7823 Like, Tweet, and Subscribe to us!
- Page 16 The sole obligation of Kurt Manufacturing Company, Inc. (Kurt) and the purchaser’s SOLE AND EXCLUSIVE REMEDY hereunder, shall be limited to the replacement or repair of any Kurt product or part (by an authorized Kurt technician) which are returned to Kurt Manufacturing Company’s place of business, transportation, shipping and postal charges prepaid, and there determined by Kurt Manufacturing Company to be covered by the warranty contained herein.