The IP Router can operate as a line and/or backbone coupler. In both cases, the LAN (IP) acts as a backbone. Figure 2: KNX IP Router as Line Coupler MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 5
Technical Manual IP-Router SCN-IP100.01 Figure 3: KNX IP Router as a backbone coupler Figure 4: KNX IP Router as a backbone and line coupler MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
The KNX IP Router can be used as an interface to KNX/EIB. KNX/EIB can be accessed from any point in the LAN. For this purpose, a second physical address must be assigned as described in the ETS Connection Manager section. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
DHCP server). Manual: In this case, the IP address, the subnet and the gateway IP address must be entered manually. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
IP ad-dress is required, it must lie within the range of 239.0.0.0 to 239.255.255.255. IP address: This is the IP address of the KNX IP Router. Figure 7: IP configuration 2 MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 9
It must be ensured that no numbers are assigned twice. IP address of the IP router: 192.168.1.31 Subnet of the IP router: 255.255.255.0 MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
IP. Broadcast telegrams: Block: No received broadcast telegrams are routed to IP. Route: All received broadcast telegrams are routed to IP. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
3.4 Routing (IP -> KNX) The following parameters can be set at the Routing KNX --> IP: Figure 9: Routing (IP --> KNX) MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 12
The received broadcast telegram is not resent to KNX/EIB in case of a fault. Enable: The received broadcast telegram is re-sent up to three times in case of a fault. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Figure 10: Communication Manager A dummy device may have to be added to the ETS project to reserve this address. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
All activities on the device should only be done by an electrical specialist. The county specific regulations and the applicable EIB-directives have to be observed. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 16
Line Coupler 2SU MDRC MDT technologies offers four KNX Interfaces to enable communication between PC and the KNX/EIB system. KNX USB Interface: The USB Interface enables the communication between the PC and the KNX/EIB system. The USB interface is galvanically isolated from the KNX/EIB bus.
Page 17
Enclosure IP 20 IP 20 IP 20 IP 20 Dimensions MDRC (Space Units) DIN EN ISO 9001 MDT technologies GmbH 51766 Engelskirchen Papiermühle 1 • • TAW Cert Tel.: + 49 - 2263 - 880 Fax: + 49 - 2263 - 4588 knx@mdt.de...